wiring diagram CHRYSLER CARAVAN 2005 Workshop Manual

The blower motor relay terminals are connected to
the vehicle electrical system through a receptacle in
the Integrated Power Module (IPM). The inputs and
outputs of the blower motor relay include:
²The common feed terminal (30) receives a bat-
tery current input from the battery through a B(+)
circuit at all times.
²The coil ground terminal (85) receives a ground
input through the front/rear blower motor relay con-
trol circuit only when the FCM electronically pulls
the control circuit to ground.
²The coil battery terminal (86) receives a battery
current input from the battery through a B(+) circuit
at all times.
²The normally open terminal (87) provides a bat-
tery current output to the blower motor resistor
(manual heater-A/C control) or blower power module
(automatic heater-A/C control) through a fuse in the
IPM on the fused front blower motor relay output cir-
cuit only when the blower motor relay coil is ener-
gized.
²The normally closed terminal (87A) is not con-
nected to any circuit in this application, but provides
a battery current output only when the blower motor
relay coil is de-energized.
Refer to the appropriate wiring information for
diagnosis and testing of the micro-relay and for com-
plete HVAC wiring diagrams.
REMOVAL
(1) Disconnect and isolate the negative battery
cable.
(2) Remove the cover from the integrated power
module (IPM) (Fig. 13).
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the IPM for front blower
motor relay identification and location.
(3) Remove the front blower motor relay from the
IPM
INSTALLATION
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the integrated power module
(IPM) for front blower motor relay identification and
location.
(1) Position the front blower motor relay to the
proper receptacle in the IPM.
(2) Align the front blower motor relay terminals
with the terminal cavities in the IPM receptacle.
(3) Push down firmly on the front blower motor
relay until the terminals are fully seated in the ter-
minal cavities.
(4) Install the cover onto the IPM.(5) Reconnect the negative battery cable.
BLOWER MOTOR RESISTOR
BLOCK
DESCRIPTION
A blower motor resistor is used on this model when
it is equipped with the manual heater-A/C system.
Models equipped with the optional Automatic Tem-
perature Control (ATC) system use a blower power
module, instead of the blower motor resistor block
(Refer to 24 - HEATING & AIR CONDITIONING/
CONTROLS/POWER MODULE - DESCRIPTION).
The blower motor resistor block is mounted to the
rear of the HVAC housing, directly behind the glove
box opening in the instrument panel. The resistor
block consists of a molded plastic mounting plate
with two integral connector receptacles. Concealed
behind the mounting plate are four coiled resistor
wires contained within a protective stamped steel
cage. The blower motor resistor block is accessed for
service by removing the glove box from the instru-
ment panel.
OPERATION
The blower motor resistor block is connected to the
vehicle electrical system through a dedicated take
out and connector of the instrument panel wire har-
ness. A second connector receptacle receives the pig-
tail wire connector from the blower motor. The
blower motor resistor has multiple resistor wires,
Fig. 13 Front Blower Motor Relay
1 - INTEGRATED POWER MODULE (IPM)
2 - FRONT BLOWER MOTOR RELAY
2 - FRONT CONTROL MODULE (FCM)
24 - 24 CONTROLS - FRONTRS
BLOWER MOTOR RELAY (Continued)

each of which will reduce the current flow through
the blower motor to change the blower motor speed.
The blower motor switch in the manual heater-A/C
system directs the ground path for the blower motor
through the correct resistor wire to obtain the
selected speed.
With the blower motor switch in the lowest speed
position, the ground path for the motor is applied
through all of the resistor wires. Each higher speed
selected with the blower motor switch applies the
blower motor ground path through fewer of the resis-
tor wires, increasing the blower motor speed.
The blower motor resistor cannot be adjusted or
repaired and, if faulty or damaged, it must be
replaced.
DIAGNOSIS AND TESTING
FRONT BLOWER MOTOR RESISTOR BLOCK
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, refer to the
appropriate wiring information. The wiring informa-
tion includes wiring diagrams, proper wire and con-
nector repair procedures, further details on wire
harness routing and retention, as well as pin-out and
location views for the various wire harness connec-
tors, splices and grounds.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the glove box from the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
GLOVE BOX - REMOVAL).
(3) Disconnect the two wire harness connectors
from the blower motor resistor block.
(4) Check for continuity between each of the
blower motor switch input terminals of the resistor
and the resistor output terminal. In each case there
should be continuity. If OK, repair the wire harness
circuits between the blower motor switch and the
blower motor resistor, blower motor or blower motorrelay as required. If not OK, replace the faulty
blower motor resistor block.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
WARNING: THE BLOWER MOTOR RESISTOR
BLOCK MAY GET VERY HOT DURING NORMAL
OPERATION. IF THE BLOWER MOTOR WAS
TURNED ON PRIOR TO SERVICING THE BLOWER
MOTOR RESISTOR BLOCK, WAIT FIVE MINUTES
TO ALLOW THE BLOWER MOTOR RESISTORS TO
COOL BEFORE PERFORMING DIAGNOSIS OR SER-
VICE. FAILURE TO TAKE THIS PRECAUTION CAN
RESULT IN PERSONAL INJURY.
CAUTION: Do not operate the blower motor with the
blower motor resistor removed from the circuit.
Failure to take this precaution can result in vehicle
damage.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the glove box from the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
GLOVE BOX - REMOVAL).
(3) Disconnect the two wire harness connectors
from the blower motor resistor block (Fig. 14).
(4) Remove the two screws that secure the blower
motor resistor block to the HVAC housing.
(5) Remove the resistor block from the HVAC
housing.
INSTALLATION
(1) Position the blower motor resistor block into
the HVAC housing.
(2) Install the two screws that secure the blower
motor resistor block to the HVAC housing. Tighten
the screws to 2 N´m (17 in. lbs.).
(3) Connect the two wire connectors to the resistor
block.
RSCONTROLS - FRONT24-25
BLOWER MOTOR RESISTOR BLOCK (Continued)

²The normally open terminal (87) provides a bat-
tery current output to the blower motor resistor
(manual heater-A/C control) or blower power module
(ATC heater-A/C control) through a fuse in the IPM
on the fused rear blower motor relay output circuit
only when the blower motor relay coil is energized.
²The normally closed terminal (87A) is not con-
nected to any circuit in this application, but provides
a battery current output only when the rear blower
motor relay coil is de-energized.
Refer to the appropriate wiring information for
diagnosis and testing of the micro-relay and for com-
plete HVAC wiring diagrams.
REMOVAL
(1) Disconnect and isolate the negative battery
cable.
(2) Remove the cover from the integrated power
module (IPM) (Fig. 5).
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the IPM for rear blower
motor relay identification and location.
(3) Remove the rear blower motor relay from the
IPM.
INSTALLATION
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the integrated power module
(IPM) for rear blower motor relay identification and
location.
(1) Position the rear blower motor relay to the
proper receptacle in the IPM.
(2) Align the rear blower motor relay terminals
with the terminal cavities in the IPM receptacle.
(3) Push down firmly on the rear blower motor
relay until the terminals are fully seated in the ter-
minal cavities.
(4) Install the cover onto the IPM.
(5) Reconnect the negative battery cable.
BLOWER MOTOR RESISTOR
BLOCK
DESCRIPTION
A rear blower motor resistor is used on this model
when it is equipped with the manual heater-A/C sys-
tem. Models equipped with the optional Automatic
Temperature Control (ATC) system use a rear blower
motor power module, instead of the blower motor
resistor block (Refer to 24 - HEATING & AIR CON-
DITIONING/CONTROLS/POWER MODULE -
DESCRIPTION). The rear blower motor resistor
block is mounted to the rear HVAC housing, directly
above the expansion valve. The resistor block con-
sists of a molded plastic mounting plate with an inte-
gral connector receptacle. Concealed behind the
mounting plate is an electrical circuit board with two
resistors and a thermal fuse. The rear blower motor
resistor block is accessed for service by removing the
right quarter and D-pillar trim panels.
OPERATION
The rear blower motor resistor block is connected
to the vehicle electrical system through a dedicated
take out and connector of the rear HVAC wire har-
ness. The blower motor resistor has an electrical cir-
cuit board with two resistors, each of which will
reduce the current flow through the blower motor to
change the blower motor speed. The blower motor
switch in the manual heater-A/C system directs the
ground path for the rear blower motor through the
correct resistor to obtain the selected speed.
Fig. 5 Rear Blower Motor Relay
1 - INTEGRATED POWER MODULE (IPM)
2 - REAR BLOWER MOTOR RELAY
3 - FRONT CONTROL MODULE (FCM)
RSCONTROLS - REAR24-37
BLOWER MOTOR RELAY (Continued)

With the blower motor switch in the lowest speed
position, the ground path for the motor is applied
through both resistors. Each higher speed selected
with the blower motor switch applies the blower
motor ground path through fewer of the resistors,
increasing the blower motor speed. When the blower
motor switch is in the highest speed position, the
blower motor resistors are bypassed and the blower
motor receives a direct path to ground through the
blower motor switch.
The rear blower motor resistor block cannot be
adjusted or repaired and, if faulty or damaged, it
must be replaced.
DIAGNOSIS AND TESTING
REAR BLOWER MOTOR RESISTOR BLOCK
For circuit descriptions and diagrams, refer to the
appropriate wiring information. The wiring informa-
tion includes wiring diagrams, proper wire and con-
nector repair procedures, further details on wire
harness routing and retention, as well as pin-out and
location views for the various wire harness connec-
tors, splices and grounds.
(1) Disconnect and isolate the battery negative
cable.
(2) Disconnect the rear HVAC wire harness con-
nector from the rear blower motor resistor.
(3) Check for continuity between each of the
blower motor switch input terminals of the blower
motor resistor and the resistor output terminal. In
each case there should be continuity. If OK, repair
the wire harness circuits between the blower motor
switch and the blower motor resistor, blower motor or
blower motor relay as required. If not OK, replace
the faulty blower motor resistor block.
REMOVAL
WARNING: THE REAR BLOWER MOTOR RESISTOR
BLOCK MAY GET VERY HOT DURING NORMAL
OPERATION. IF THE BLOWER MOTOR WAS
TURNED ON PRIOR TO SERVICING THE BLOWER
MOTOR RESISTOR BLOCK, WAIT FIVE MINUTES
TO ALLOW THE BLOWER MOTOR RESISTORS TO
COOL BEFORE PERFORMING DIAGNOSIS OR SER-
VICE. FAILURE TO TAKE THIS PRECAUTION CAN
RESULT IN PERSONAL INJURY.CAUTION: Do not operate the blower motor with the
blower motor resistor block removed from the cir-
cuit. Failure to take this precaution can result in
vehicle damage.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the right quarter trim panel and right
D-pillar trim panel from the quarter inner panel
(Refer to 23 - BODY/INTERIOR/QUARTER TRIM
PANEL - REMOVAL).
(3) Disconnect the rear HVAC wire harness con-
nector from the blower motor resistor block (Fig. 6).
(4) Remove the two screws that secure the blower
motor resistor block to the rear HVAC housing.
(5) Remove the rear blower motor resistor block
from the rear HVAC housing.
Fig. 6 Rear Blower Motor Resistor Block
1 - REAR HVAC HOUSING
2 - D-PILLAR
3 - BLOWER PIGTAIL WIRE
4 - CONNECTOR
5 - EXPANSION VALVE
6 - SCREW (2)
7 - BLOWER MOTOR RESISTOR BLOCK
24 - 38 CONTROLS - REARRS
BLOWER MOTOR RESISTOR BLOCK (Continued)

whenever the ignition switch is in the On position
and the A/C-heater control power is turned on.
The blower motor receives battery current when-
ever the front blower motor relay is energized. The
front blower motor relay output circuit is protected
by a fuse in the Integrated Power Module (IPM)
located in the engine compartment near the battery.
In the manual heater-A/C system, the blower motor
speed is controlled by regulating the path to ground
through the blower control switch and the blower
motor resistor. In the ATC system, the blower motor
speed is controlled by an electronic blower motor
power module, which uses a pulse width modulated
input from the ATC module and feedback from the
blower motor to regulate the blower motor ground
path it provides. The blower motor and wheel are
used to control the velocity of air moving through the
HVAC housing by spinning the blower wheel within
the housing at the selected speed or, in the ATC sys-
tem, at the selected or programmed speed.
DIAGNOSIS AND TESTING
FRONT BLOWER MOTOR
BLOWER MOTOR INOPERATIVE
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, refer to the
appropriate wiring information. The wiring informa-
tion includes wiring, diagrams, proper wire and con-
nector repair procedures, further details on wire
harness routing and retention, as well as pin-out and
location views for the various wire harness connec-
tors, splices and grounds.BLOWER MOTOR ELECTRICAL DIAGNOSIS
(1) Check the fuse (Fuse 10 - 40 ampere) in the
Integrated Power Module (IPM). If OK, go to Step 2.
If not OK, repair the shorted circuit or component as
required and replace the faulty fuse.
(2) Turn the ignition switch to the On position. Be
certain that the A/C-heater control power is turned
on. Check for battery voltage at the fuse (Fuse 10 -
40 ampere) in the IPM. If OK, go to Step 3. If not
OK, check the front blower motor relay.
(3) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the front HVAC wire harness connector
for the front blower motor resistor block (Manual
Temperature Control) or the front blower motor
power module (Automatic Temperature Control) from
the resistor or module connector receptacle. Recon-
nect the battery negative cable. Turn the ignition
switch to the On position. Be certain that the A/C-
heater control power is turned on. Check for battery
voltage at the fused front blower motor relay output
circuit cavity of the front HVAC wire harness connec-
tor for the front blower motor resistor block (MTC) or
the front blower motor power module (ATC). If OK,
go to Step 4. If not OK, repair the open fused front
blower motor relay output circuit to the IPM as
required.
(4) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the front blower motor pigtail wire con-
nector from the connector receptacle of the front
blower motor resistor block (MTC) or the front
blower motor power module (ATC). Use jumper wires
to connect a battery and ground feeds to the blower
motor pigtail wire connector. The blower motor
should operate. If OK with MTC, proceed to diagno-
sis of the front blower motor resistor block (Refer to
24 - HEATING & AIR CONDITIONING/CONTROLS
- FRONT/BLOWER MOTOR RESISTOR - DIAGNO-
SIS AND TESTING). If OK with ATC, use a DRBIII
scan tool to diagnose the front blower motor power
module. Refer to Body Diagnostic information. If not
OK with MTC or ATC, replace the faulty front blower
motor.
BLOWER MOTOR NOISE OR VIBRATION
Refer to the Blower Motor Noise/Vibration Diagno-
sis chart for basic checks of the blower motor when a
vibration or noise is present (Fig. 7).
24 - 46 DISTRIBUTION - FRONTRS
BLOWER MOTOR (Continued)

DIAGNOSIS AND TESTING
REAR BLOWER MOTOR
BLOWER MOTOR INOPERATIVE
For circuit descriptions and diagrams, refer to the
appropriate wiring information. The wiring informa-
tion includes wiring, diagrams, proper wire and con-
nector repair procedures, further details on wire
harness routing and retention, as well as pin-out and
location views for the various wire harness connec-
tors, splices and grounds.
BLOWER MOTOR ELECTRICAL DIAGNOSIS
(1) Check the fuse (Fuse 12 - 25 ampere) in the
Integrated Power Module (IPM). If OK, go to Step 2.
If not OK, repair the shorted circuit or component as
required and replace the faulty fuse.
(2) Turn the ignition switch to the On position. Be
certain that the rear A/C-heater control power is
turned on. Check for battery voltage at the fuse
(Fuse 12 - 25 ampere) in the IPM. If OK, go to Step
3. If not OK, check the rear blower motor relay.
(3) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the rear HVAC wire harness connector
from the rear blower motor resistor block (Manual
Temperature Control) or the rear blower motor power
module (Automatic Temperature Control). Reconnect
the battery negative cable. Turn the ignition switch
to the On position. Be certain that the rear A/C-
heater control power is turned on. Check for battery
voltage at the fused rear blower motor relay output
circuit cavity of the rear HVAC wire harness connec-
tor for the rear blower motor resistor block (MTC) or
the rear blower motor power module (ATC). If OK, go
to Step 4. If not OK, repair the open fused front
blower motor relay output circuit to the IPM as
required.
(4) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.Disconnect the rear blower motor pigtail wire connec-
tor from the rear HVAC wire harness (MTC) or the
rear blower power module (ATC). Use jumper wires
to connect a battery and ground feeds to the blower
motor pigtail wire connector. The rear blower motor
should operate. If OK with MTC, proceed to diagno-
sis of the rear blower motor resistor block (Refer to
24 - HEATING & AIR CONDITIONING/CONTROLS
- REAR/BLOWER MOTOR RESISTOR - DIAGNOSIS
AND TESTING). If OK with ATC, use a DRBIII scan
tool to diagnose the rear blower motor power module.
Refer to the appropriate diagnostic information. If
not OK with MTC or ATC, replace the faulty rear
blower motor.
BLOWER MOTOR NOISE OR VIBRATION
Refer to the Blower Motor Noise/Vibration Diagno-
sis chart for basic checks of the blower motor when a
vibration or noise is present (Fig. 3).
REMOVAL
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
WARNING) and (Refer to 24 - HEATING & AIR CON-
DITIONING/PLUMBING - CAUTION).
(1) Remove the rear HVAC housing from the vehi-
cle (Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION/HVAC HOUSING - REMOVAL).
(2) Disconnect the rear blower motor pigtail wire
connector.
NOTE: With the Manual Temperature Control sys-
tem, the blower motor pigtail wire is connected to a
take out and connector of the rear HVAC wire har-
ness. With the Automatic Temperature Control sys-
tem , the blower pigtail wire is connected to a
receptacle on the blower motor power module.
24 - 58 DISTRIBUTION - REARRS
BLOWER MOTOR (Continued)

DEFOGGER RELAY - DESCRIPTION,REAR WINDOW ....................... 8G-3
DEFOGGER RELAY - INSTALLATION, REAR WINDOW ....................... 8G-4
DEFOGGER RELAY - OPERATION, REAR WINDOW ............................ 8G-3
DEFOGGER RELAY - REMOVAL, REAR WINDOW ............................ 8G-4
DEFOGGER SWITCH - DESCRIPTION, REAR WINDOW ....................... 8G-4
DEFOGGER SWITCH - OPERATION, REAR WINDOW ............................ 8G-4
DEFROSTER DUCT - INSTALLATION ......24-50
DEFROSTER DUCT - REMOVAL ..........24-49
DEMAGNETIZING, STANDARD PROCEDURE - COMPASS ...............8M-5
DEMISTER DUCTS - INSTALLATION, INSTRUMENT PANEL .................. 24-54
DEMISTER DUCTS - REMOVAL, INSTRUMENT PANEL .................. 24-54
DEMISTER OUTLETS, INSTALLATION - FRONT ............................. 24-45
DEMISTER OUTLETS, REMOVAL - FRONT . 24-44
DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER AN
AIRBAG ............................. 8O-7
DETECTION ASSY - INSTALLATION, NATURAL VAC LEAK .................. 25-14
DETECTION ASSY - REMOVAL, NATURAL VAC LEAK .......................... 25-14
DETECTION PUMP - INSTALLATION, LEAK .............................. 25-15
DETECTION PUMP - REMOVAL, LEAK ......25-15
DEVICES - STANDARD PROCEDURE, ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE ........................8W -01-8
DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING - ON-BOARD .................8F-22
DIAGNOSTIC TROUBLE CODES - STANDARD PROCEDURE, OBTAINING .....8E-15
DIAGRAMS - 4XTE TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS .................. 21-199,21-54
DIAGRAMS - DESCRIPTION, HOW TO USE WIRING ......................8W -01-1
DIAGRAMS - SPECIAL TOOLS, SCHEMATICS ........................ 21-68
DIESEL - DESCRIPTION ...............19-52
DIESEL - INSTALLATION ...............19-53
DIESEL - REMOVAL ................... 19-52
DIESEL ENGINE - DESCRIPTION, FUEL REQUIREMENTS .......................0-6
DIESEL ENGINES - DESCRIPTION, ENGINE OIL ...........................0-6
DIESEL ENGINES - EXPORT - DESCRIPTION ........................ 0-21
DIESEL ENGINES, INSTALLATION - 2.5L/2.8L ........................... 24-78
DIESEL ENGINES, REMOVAL - 2.5L/2.8L . . 24-77
DIFFERENTIAL BEARING PRELOAD - ADJUSTMENT ...................... 21-228
DIFFERENTIAL BEARING PRELOAD MEASUREMENT AND ADJUSTMENT,
ADJUSTMENTS ...................... 21-79
DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME ........13-11
DIMENSIONS - SPECIFICATIONS, BODY OPENING .......................... 23-180
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-6
DIODE - INSTALLATION ............8W-01-14
DIODE - REMOVAL ................8W -01-14
DISABLED INDICATOR - DESCRIPTION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - INSTALLATION, PASSENGER AIRBAG .................8O-34
DISABLED INDICATOR - OPERATION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - REMOVAL, PASSENGER AIRBAG .................8O-34
DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE, TRANSMISSION COOLER
LINE QUICK CONNECT FITTING ...........7-38
DISC BRAKE CALIPER - INSTALLATION, REAR ............................... 5-30
DISC BRAKE CALIPER - REMOVAL, REAR ............................... 5-28
DISC BRAKE CALIPER ADAPTER - INSTALLATION, FRONT .................5-31DISC BRAKE CALIPER ADAPTER -
REMOVAL, FRONT ..................... 5-31
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-27
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-24
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION ...............5-32
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL .................. 5-31
DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION, FRONT .................5-27
DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL, FRONT ..................... 5-24
DISC BRAKE SHOES - CLEANING .....5-16,5-18
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18
DISC BRAKE SHOES - INSTALLATION, REAR ............................... 5-19
DISC BRAKE SHOES - REMOVAL, REAR ....5-17
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-16
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-15
DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION, FRONT .................5-17
DISC BRAKE SHOES (TRW BRAKES) - REMOVAL, FRONT ..................... 5-15
DISC BRAKES (EXPORT) - DESCRIPTION . . . 5-13
DISC BRAKES (FRONT) - DESCRIPTION ....5-11
DISC BRAKES (FRONT) - OPERATION ......5-13
DISC BRAKES (REAR) - DESCRIPTION .....5-13
DISC BRAKES (REAR) - OPERATION ......5-14
DISCHARGE (ESD) SENSITIVE DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC ...................8W -01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-80
DISCHARGE LINE - REMOVAL, A/C .......24-79
DISPLAY - DESCRIPTION, PARK ASSIST . . . 8B-3
DISPLAY - INSTALLATION, PARK ASSIST . . . 8B-4
DISPLAY - OPERATION, PARK ASSIST .....8B-3
DISPLAY - REMOVAL, PARK ASSIST ......8B-4
DISPLAY TEST MODE, OPERATION - DRB III T STATE .......................... 25-10
DISSASEMBLY, REMOVAL ..............24-51
DISTRIBUTION DUCT - INSTALLATION ....24-57
DISTRIBUTION DUCT - REMOVAL ........24-57
DISTRIBUTION DUCTS - INSTALLATION, FLOOR ............................. 24-50
DISTRIBUTION DUCTS - REMOVAL, FLOOR ............................. 24-50
DISTRIBUTION SYSTEM - DESCRIPTION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEM - OPERATION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEMS, SPECIAL TOOLS - POWER ...................8W -97-1
DOES NOT FILL - DIAGNOSIS AND TESTING, VEHICLE ................... 25-17
DOME/CARGO LAMP - INSTALLATION ....8L-22
DOME/CARGO LAMP - REMOVAL ........8L-22
DOOR - INSTALLATION ................23-15
DOOR - INSTALLATION, FUEL FILL .......23-52
DOOR - INSTALLATION, SLIDING ........23-29
DOOR - REMOVAL .................... 23-15
DOOR - REMOVAL, FUEL FILL ..........23-52
DOOR - REMOVAL, SLIDING ............23-29
DOOR ACTUATOR - DESCRIPTION, BLEND ........................ 24-22,24-34
DOOR ACTUATOR - DESCRIPTION, MODE ............................. 24-29
DOOR ACTUATOR - DESCRIPTION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - INSTALLATION, BLEND ........................ 24-22,24-35
DOOR ACTUATOR - INSTALLATION, MODE ............................. 24-30
DOOR ACTUATOR - INSTALLATION, RECIRCULATION ..................... 24-32
DOOR ACTUATOR - OPERATION, BLEND . . 24-22,
24-35
DOOR ACTUATOR - OPERATION, MODE . . . 24-29
DOOR ACTUATOR - OPERATION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - REAR - DESCRIPTION, MODE .................24-39DOOR ACTUATOR - REAR -
INSTALLATION, MODE .................24-40
DOOR ACTUATOR - REAR - OPERATION, MODE ............................. 24-39
DOOR ACTUATOR - REAR - REMOVAL, MODE ............................. 24-39
DOOR ACTUATOR - REMOVAL, BLEND . . . 24-22, 24-35
DOOR ACTUATOR - REMOVAL, MODE ....24-29
DOOR ACTUATOR - REMOVAL, RECIRCULATION ..................... 24-32
DOOR ADJUSTMENT, STANDARD PROCEDURE - POWER SLIDING .........8N-49
DOOR ADJUSTMENTS, ADJUSTMENTS - SLIDING ............................ 23-30
DOOR BLOCKER LATCH - INSTALLATION, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH - REMOVAL, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL FILL .............23-53
DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL FILL .................23-53
DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL FILL .............23-54
DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL FILL .................23-54
DOOR CONTROL MODULE - DESCRIPTION, SLIDING ...............8E-18
DOOR CONTROL MODULE - OPERATION, SLIDING ............................ 8E-18
DOOR CONTROL MODULE, DIAGNOSIS AND TESTING - SLIDING ...............8E-18
DOOR CYLINDER LOCK SWITCH - EXPORT - DESCRIPTION ...............8N-22
DOOR CYLINDER LOCK SWITCH - EXPORT - OPERATION ................8N-22
DOOR CYLINDER LOCK SWITCH, EXPORT ............................ 8N-22
DOOR GLASS - INSTALLATION ..........23-17
DOOR GLASS - INSTALLATION, SLIDING . 23-163
DOOR GLASS - REMOVAL .............23-16
DOOR GLASS - REMOVAL, SLIDING .....23-163
DOOR GLASS RUN WEATHERSTRIP - INSTALLATION, FRONT ...............23-166
DOOR GLASS RUN WEATHERSTRIP - REMOVAL, FRONT ................... 23-166
DOOR INNER BELT MOLDING - INSTALLATION, FRONT ...............23-168
DOOR INNER BELT MOLDING - REMOVAL, FRONT ................... 23-168
DOOR LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING .........8N-48
DOOR LOCK MOTOR - INSTALLATION, SLIDING ........................... 8N-25
DOOR LOCK MOTOR - REMOVAL, SLIDING ........................... 8N-25
DOOR LOCK MOTOR, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR LOCK SWITCH, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR MOTOR - DESCRIPTION, SLIDING . . 8N-51
DOOR MOTOR - INSTALLATION, SLIDING . 8N-51
DOOR MOTOR - OPERATION, SLIDING . . . 8N-51
DOOR MOTOR - REMOVAL, SLIDING .....8N-51
DOOR OUTER BELT MOLDING - INSTALLATION, FRONT ...............23-167
DOOR OUTER BELT MOLDING - REMOVAL, FRONT ................... 23-167
DOOR SILL PLATE - INSTALLATION, SLIDING ............................ 23-99
DOOR SILL PLATE - REMOVAL, SLIDING . . 23-98
DOOR SILL TRIM PLATE - INSTALLATION ....................... 23-89
DOOR SILL TRIM PLATE - REMOVAL .....23-89
DOOR STOP BUMPER BEZEL - INSTALLATION, SLIDING ...............23-25
DOOR STOP BUMPER BEZEL - REMOVAL, SLIDING .................. 23-25
DOOR SYSTEM - DESCRIPTION, POWER SLIDING ........................... 8N-40
DOOR SYSTEM - OPERATION, POWER SLIDING ........................... 8N-41
DOOR SYSTEM, DIAGNOSIS AND TESTING - POWER SLIDING ............8N-42
DOOR WEATHERSTRIP - INSTALLATION, FRONT ............................ 23-168
10 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

TO CYLINDER BORE FITTING -STANDARD PROCEDURE, PISTON ........9-44
TO FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP ...........7-28
TO GROUND - STANDARD PROCEDURE, TESTING FOR A SHORT .............8W-01-9
TO GROUND ON FUSES POWERING SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS - DESCRIPTION, HOW ................8W -01-1
TONE WHEEL - INSPECTION .............5-94
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-91
TOOLS - 2.4L ENGINE, SPECIAL ..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL .......9-98
TOOLS - 41TE AUTOMATIC TRANSAXLE, SPECIAL .......................... 21-213
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10
TOOLS - BATTERY SYSTEM SPECIAL TOOLS, SPECIAL ...................... 8F-7
TOOLS - BODY, SPECIAL ...............23-13
TOOLS - COOLING SYSTEM, SPECIAL ......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL .....11-4
TOOLS - FRONT SUSPENSION, SPECIAL ....2-3
TOOLS - FUEL, SPECIAL ...........14-27,14-4
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-7
TOOLS - POWER DISTRIBUTION SYSTEMS, SPECIAL ................8W -97-1
TOOLS - POWER STEERING GEAR, SPECIAL ........................... 19-34
TOOLS - POWER STEERING PUMP, SPECIAL ........................... 19-44
TOOLS - POWER STEERING, SPECIAL .....19-9
TOOLS - REAR SUSPENSION, SPECIAL ....2-28
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, SCHEMATICS AND DIAGRAMS - SPECIAL ........................... 21-68
TOOLS, SPECIAL TOOLS - BATTERY SYSTEM SPECIAL ..................... 8F-7
TOOLS, SPECIFICATIONS - SPECIAL ......8F-24
TOP COVER - INSTALLATION, INSTRUMENT PANEL .................. 23-72
TOP COVER - REMOVAL, INSTRUMENT PANEL ............................. 23-72
TOP PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL .................. 23-77
TOP PAD ASSEMBLY - REMOVAL, INSTRUMENT PANEL .................. 23-77
TORQUES, SPECIFICATIONS ............8F-36
TOUCH-UP - DESCRIPTION, PAINTED ....23-101
TOWING - STANDARD PROCEDURE .......0-26
TPM - CAUTION, SENSOR ..............22-11
TPM - DESCRIPTION, SENSOR ..........22-10
TPM - INSTALLATION, SENSOR .........22-11
TPM - OPERATION, SENSOR ............22-10
TPM - REMOVAL, SENSOR .............22-11
TRACK - DESCRIPTION, POWER SEAT ....8N-37
TRACK - INSTALLATION, BENCH SEAT . . . 23-148
TRACK - OPERATION, POWER SEAT .....8N-38
TRACK & RACK - DESCRIPTION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - INSTALLATION, LOWER DRIVE UNIT .................. 8N-58
TRACK & RACK - OPERATION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - REMOVAL, LOWER DRIVE UNIT ........................ 8N-57
TRACK - REAR COVER - INSTALLATION, FRONT SEAT ....................... 23-128
TRACK - REAR COVER - REMOVAL, FRONT SEAT ....................... 23-128
TRACK - REMOVAL, BENCH SEAT .......23-148
TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT SEAT ..........23-128
TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT SEAT ..............23-126
TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT SEAT ..........23-125
TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT SEAT ..............23-124
TRACK BAR - DESCRIPTION .............2-45
TRACK BAR - INSTALLATION ............2-46
TRACK BAR - OPERATION ...............2-46
TRACK BAR - REMOVAL ................2-46
TRACK, DIAGNOSIS AND TESTING - POWER SEAT ....................... 8N-38
TRACK MANUAL ADJUSTER - INSTALLATION, FRONT SEAT ..........23-126TRACK MANUAL ADJUSTER - REMOVAL,
FRONT SEAT ....................... 23-125
TRACK POWER ADJUSTER - INSTALLATION, FRONT SEAT ..........23-124
TRACK POWER ADJUSTER - REMOVAL, FRONT SEAT ....................... 23-124
TRACK REAR COVER - OCS - INSTALLATION, FRONT SEAT ..........23-129
TRACK REAR COVER - OCS - REMOVAL, FRONT SEAT ....................... 23-129
TRACTION CONTROL SWITCH - DIAGNOSIS AND TESTING ..............5-94
TRACTION CONTROL SWITCH - INSTALLATION ........................ 5-95
TRACTION CONTROL SWITCH - REMOVAL ........................... 5-95
TRACTION CONTROL SYSTEM - DESCRIPTION ........................ 5-88
TRACTION CONTROL SYSTEM - OPERATION .......................... 5-89
TRANSAXLE - DESCRIPTION, 40TE AUTOMATIC .......................... 21-2
TRANSAXLE - DESCRIPTION, 41TE AUTOMATIC ........................ 21-147
TRANSAXLE - OPERATION, 40TE AUTOMATIC .......................... 21-4
TRANSAXLE - OPERATION, 41TE AUTOMATIC ........................ 21-149
TRANSAXLE - SPECIFICATIONS, 41TE . . . 21-211, 21-66
TRANSAXLE FLUID - DESCRIPTION, AUTOMATIC/MANUAL ...................0-4
TRANSAXLE GENERAL DIAGNOSIS - DIAGNOSIS AND TESTING, 4XTE .....21-149,21-5
TRANSAXLE HYDRAULIC SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE . . . 21-199, 21-54
TRANSAXLE, SPECIAL TOOLS - 41TE AUTOMATIC ........................ 21-213
TRANSDUCER - DESCRIPTION, A/C PRESSURE ......................... 24-20
TRANSDUCER - OPERATION, A/C PRESSURE ......................... 24-20
TRANSDUCER, DIAGNOSIS AND TESTING - A/C PRESSURE .............24-21
TRANSFER UNIT FLUID - DESCRIPTION, AWD POWER ..........................0-6
TRANSMISSION CONTROL RELAY - DESCRIPTION ................ 21-130,21-281
TRANSMISSION CONTROL RELAY - OPERATION .................. 21-130,21-281
TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/
ASSEMBLY - STANDARD PROCEDURE .....7-38
TRANSMISSION OIL COOLER - DESCRIPTION ........................ 7-39
TRANSMISSION OIL COOLER - INSPECTION ......................... 7-39
TRANSMISSION OIL COOLER LINES - INSTALLATION ........................ 7-40
TRANSMISSION OIL COOLER LINES - REMOVAL ........................... 7-39
TRANSMISSION RANGE SENSOR - DESCRIPTION ................ 21-130,21-281
TRANSMISSION RANGE SENSOR - INSTALLATION ................ 21-131,21-282
TRANSMISSION RANGE SENSOR - OPERATION .................. 21-131,21-282
TRANSMISSION RANGE SENSOR - REMOVAL ................... 21-131,21-282
TRANSMITTER - DESCRIPTION, UNIVERSAL ........................ 8M-11
TRANSMITTER CODES, STANDARD PROCEDURE - ERASING ..............8M-12
TRANSMITTER CODES, STANDARD PROCEDURE - SETTING ...............8M-12
TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS ENTRY ............8N-24
TRANSMITTER, DIAGNOSIS AND TESTING - UNIVERSAL ...............8M-11
TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ENTRY ..................... 8N-24
TRANSMITTER RANGE - SPECIFICATIONS ..................... 8N-24
TRANSPONDER KEY - DESCRIPTION ......8Q-6
TRANSPONDER KEY - OPERATION ........8Q-6TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE ...............8Q-6
TRANSVERSE BRACKET - DESCRIPTION . . 8N-19
TRANSVERSE BRACKET - INSTALLATION . . 8N-19
TRANSVERSE BRACKET - OPERATION ....8N-19
TRANSVERSE BRACKET - REMOVAL .....8N-19
TRAY - DESCRIPTION, BATTERY .........8F-19
TRAY - INSTALLATION, BATTERY ........8F-20
TRAY - INSTALLATION, FLOOR CONSOLE BASE .............................. 23-89
TRAY - REMOVAL, BATTERY ............8F-19
TRAY - REMOVAL, FLOOR CONSOLE BASE .............................. 23-89
TREAD WEAR INDICATORS - DIAGNOSIS AND TESTING ....................... 22-16
TRIM - INSTALLATION, A-PILLAR ........23-79
TRIM - INSTALLATION, A-PILLAR LOWER EXTENSION .................. 23-79
TRIM - INSTALLATION, B-PILLAR LOWER ............................ 23-80
TRIM - INSTALLATION, B-PILLAR UPPER . . 23-80
TRIM - INSTALLATION, COWL ..........23-88
TRIM - INSTALLATION, C-PILLAR ........23-88
TRIM - INSTALLATION, REAR HEADER ....23-96
TRIM - REMOVAL, A-PILLAR ...........23-79
TRIM - REMOVAL, A-PILLAR LOWER EXTENSION ......................... 23-79
TRIM - REMOVAL, B-PILLAR LOWER .....23-79
TRIM - REMOVAL, B-PILLAR UPPER .......23-80
TRIM - REMOVAL, COWL ..............23-88
TRIM - REMOVAL, C-PILLAR ...........23-88
TRIM - REMOVAL, REAR HEADER .......23-96
TRIM BOLSTER - INSTALLATION, QUARTER .......................... 23-95
TRIM BOLSTER - REMOVAL, QUARTER . . . 23-95
TRIM CARE, CLEANING - WHEEL AND WHEEL ............................ 22-19
TRIM PANEL - INSTALLATION .....23-20,23-34,
23-43
TRIM PANEL - INSTALLATION, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - INSTALLATION, LEFT QUARTER .......................... 23-94
TRIM PANEL - INSTALLATION, RIGHT D-PILLAR ........................... 23-98
TRIM PANEL - INSTALLATION, RIGHT QUARTER .......................... 23-97
TRIM PANEL - REMOVAL ....23-20,23-34,23-43
TRIM PANEL - REMOVAL, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - REMOVAL, LEFT QUARTER .......................... 23-94
TRIM PANEL - REMOVAL, RIGHT D-PILLAR ........................... 23-97
TRIM PANEL - REMOVAL, RIGHT QUARTER .......................... 23-97
TRIM PLATE - INSTALLATION, DOOR SILL ............................... 23-89
TRIM PLATE - REMOVAL, DOOR SILL ....23-89
TRIM RING AND COVER - FOLD-IN- FLOOR - INSTALLATION, CARPET ........23-84
TRIM RING AND COVER - FOLD-IN- FLOOR - REMOVAL, CARPET ...........23-84
TRIP DEFINITION, DESCRIPTION .........25-1
TROUBLE CODES - STANDARD PROCEDURE, OBTAINING DIAGNOSTIC . . . 8E-15
TUB CARPET INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR ....23-98
TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR ........23-98
TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR ..........23-96
TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR .............23-95
TUBE - 2.4L - DESCRIPTION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - INSTALLATION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - REMOVAL, WATER PUMP INLET ............................... 7-36
TUBE - 3.3/3.8L - INSTALLATION, WATER PUMP INLET ......................... 7-37
TUBE - 3.3/3.8L - REMOVAL, WATER PUMP INLET ......................... 7-37
TUBE - INSTALLATION, DRAIN .........23-172
TUBE - INSTALLATION, EXHAUST .......24-116
TUBE - INSTALLATION, FUEL TANK FILLER ............................. 14-17
RS INDEX33
Description Group-Page Description Group-Page Description Group-Page

TUBE - REMOVAL, DRAIN.............23-172
TUBE - REMOVAL, EXHAUST ..........24-116
TUBE - REMOVAL, FUEL TANK FILLER ....14-16
TUBES AND HOSES - DESCRIPTION, BRAKE .............................. 5-14
TUBES AND HOSES - INSPECTION, BRAKE .............................. 5-14
TUBES AND HOSES - OPERATION, BRAKE .............................. 5-14
TUBES, INSTALLATION - FRONT HEATER CORE .............................. 24-85
TUBES, INSTALLATION - UNDERBODY HEATER ........................... 24-112
TUBES, REMOVAL - FRONT HEATER CORE .............................. 24-84
TUBES, REMOVAL - UNDERBODY HEATER ........................... 24-109
TUBING AND FITTINGS, STANDARD PROCEDURE - HANDLING ..............24-69
TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE KEY
LOCK .............................. 23-90
TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK ............23-90
TURN SIGNAL SYSTEM - DESCRIPTION . . . 8L-17
TURN SIGNAL SYSTEM - OPERATION ....8L-17
UNDER SEAT STORAGE BIN - INSTALLATION ...................... 23-149
UNDER SEAT STORAGE BIN - REMOVAL . 23-149
UNDER SEAT STORAGE BIN GUIDE - INSTALLATION ...................... 23-150
UNDER SEAT STORAGE BIN GUIDE - REMOVAL ......................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - INSTALLATION .................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - REMOVAL ........................ 23-150
UNDERBODY HEATER TUBES, INSTALLATION ...................... 24-112
UNDERBODY HEATER TUBES, REMOVAL . 24-109
UNDERBODY LINES - DESCRIPTION .....24-108
UNDERBODY LINES - OPERATION ......24-108
UNDERBODY REFRIGERANT LINES, INSTALLATION ...................... 24-112
UNDERBODY REFRIGERANT LINES, REMOVAL ......................... 24-110
UNIT - DESCRIPTION, LOWER DRIVE ....8N-53
UNIT - EXPORT - INSTALLATION, HEADLAMP ......................... 8L-17
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-17
UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - INSTALLATION, HEADLAMP .......8L-15
UNIT - INSTALLATION, HEATER ........24-122
UNIT - INSTALLATION, LOWER DRIVE ....8N-54
UNIT - INSTALLATION, TAIL LAMP .......8L-19
UNIT - OPERATION, LOWER DRIVE ......8N-53
UNIT - REMOVAL, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - REMOVAL, HEADLAMP ..........8L-15
UNIT - REMOVAL, HEATER ............24-121
UNIT - REMOVAL, LOWER DRIVE .......8N-53
UNIT - REMOVAL, TAIL LAMP ...........8L-19
UNIT / SENSOR - DESCRIPTION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - INSTALLATION, FUEL LEVEL SENDING ...................... 14-6
UNIT / SENSOR - OPERATION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - REMOVAL, FUEL LEVEL SENDING ...................... 14-5
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG
LAMP ............................... 8L-9
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP ....8L-15
UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP .........8L-9
UNIT ALIGNMENT - STANDARD PROCEDURE, HEADLAMP ..............8L-14
UNIT FLUID - DESCRIPTION, AWD POWER TRANSFER .....................0-6
UNIT TRACK & RACK - DESCRIPTION, LOWER DRIVE ...................... 8N-57
UNIT TRACK & RACK - INSTALLATION, LOWER DRIVE ...................... 8N-58
UNIT TRACK & RACK - OPERATION, LOWER DRIVE ...................... 8N-57UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE ...................... 8N-57
UNIVERSAL TRANSMITTER - DESCRIPTION ....................... 8M-11
UNIVERSAL TRANSMITTER, DIAGNOSIS AND TESTING ....................... 8M-11
UPPER - INSPECTION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, SHROUD .......19-22
UPPER - REMOVAL, INTAKE MANIFOLD ....9-60
UPPER - REMOVAL, SHROUD ...........19-22
UPPER HINGE - INSTALLATION .........23-36
UPPER HINGE - REMOVAL .............23-36
UPPER INTAKE MANIFOLD - INSTALLATION ....................... 9-149
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-148
UPPER RADIATOR CROSSMEMBER - INSTALLATION ....................... 23-56
UPPER RADIATOR CROSSMEMBER - REMOVAL .......................... 23-56
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-80
UPPER TRIM - REMOVAL, B-PILLAR .....23-80
UPSTREAM 1/1 - 2.4L - INSTALLATION . . . 14-38
UPSTREAM 1/1 - 2.4L - REMOVAL .......14-37
UPSTREAM 1/1 - 3.3/3.8L - INSTALLATION ....................... 14-39
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL ....14-38
USE WIRING DIAGRAMS - DESCRIPTION, HOW TO .............8W-01-1
USING PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING
CLEARANCE ..................... 9-12,9-86
VAC LEAK DETECTION ASSY - INSTALLATION, NATURAL ..............25-14
VAC LEAK DETECTION ASSY - REMOVAL, NATURAL .................. 25-14
VACUUM PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD ........9-148
VACUUM RESERVOIR - DESCRIPTION .....8P-6
VACUUM RESERVOIR - INSTALLATION ....8P-6
VACUUM RESERVOIR - OPERATION .......8P-6
VACUUM RESERVOIR - REMOVAL ........8P-6
VALVE - DESCRIPTION ................25-23
VALVE - DESCRIPTION, A/C EXPANSION . 24-100
VALVE - DESCRIPTION, EXPANSION ......24-81
VALVE - DESCRIPTION, PCV ............25-18
VALVE - INSTALLATION, OIL PRESSURE RELIEF ............................. 9-144
VALVE - OPERATION ..................25-23
VALVE - OPERATION, A/C EXPANSION . . . 24-100
VALVE - OPERATION, EXPANSION .......24-81
VALVE - OPERATION, PCV ..............25-18
VALVE - REMOVAL, OIL PRESSURE RELIEF ............................. 9-143
VALVE BODY - ASSEMBLY ......21-139,21-291
VALVE BODY - DESCRIPTION ....21-132,21-283
VALVE BODY - DISASSEMBLY ....21-135,21-286
VALVE BODY - INSTALLATION ....21-144,21-295
VALVE BODY - OPERATION ......21-132,21-283
VALVE BODY - REMOVAL .......21-133,21-284
VALVE CORE - DESCRIPTION, SERVICE PORT.............................. 24-95
VALVE CORE - INSTALLATION, SERVICE PORT.............................. 24-95
VALVE CORE - REMOVAL, SERVICE PORT.............................. 24-95
VALVE, DESCRIPTION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE, DIAGNOSIS AND TESTING - FRONT A/C EXPANSION ...............24-82
VALVE, DIAGNOSIS AND TESTING - REAR A/C EXPANSION ...............24-101
VALVE (HEIGHT SENSING) - DESCRIPTION, PROPORTIONING .........5-53
VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING, PROPORTIONING .........5-54
VALVE (HEIGHT SENSING) - INSTALLATION, PROPORTIONING .........5-55
VALVE (HEIGHT SENSING) - OPERATION, PROPORTIONING ..................... 5-53
VALVE (HEIGHT SENSING) - REMOVAL, PROPORTIONING ..................... 5-55
VALVE, OPERATION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE SEATS - STANDARD PROCEDURE, REFACING VALVES ................... 9-107VALVE SPRINGS - DESCRIPTION
........9-109
VALVE SPRINGS - OPERATION ..........9-109
VALVE STEM SEALS - DESCRIPTION .....9-114
VALVE STEM SEALS - INSTALLATION .....9-115
VALVE STEM SEALS - REMOVAL ........9-115
VALVE TIMING VERIFICATION - STANDARD PROCEDURE ...............9-155
VALVES - OPERATION, HYDRAULIC CIRCUITS ............................ 5-95
VALVES & SEATS - CLEANING, INTAKE/EXHAUST ................ 9-108,9-33
VALVES & SEATS - DESCRIPTION, INTAKE/EXHAUST ................ 9-107,9-33
VALVES & SEATS - INSPECTION, INTAKE/EXHAUST .................... 9-108
VALVES & SEATS - INSTALLATION, INTAKE/EXHAUST .................... 9-109
VALVES & SEATS - OPERATION, INTAKE/EXHAUST .................... 9-107
VALVES & SEATS - REMOVAL, INTAKE/EXHAUST .................... 9-108
VALVES AND VALVE SEATS - STANDARD PROCEDURE, REFACING ...............9-107
VANITY LAMP - INSTALLATION .........8L-24
VANITY LAMP - REMOVAL .............8L-24
VAPOR CANISTER - DESCRIPTION .......25-19
VAPOR CANISTER - OPERATION .........25-19
VARIABLE BRAKE PROPORTIONING - DESCRIPTION, ELECTRONIC .............5-88
VARIABLE BRAKE PROPORTIONING - OPERATION, ELECTRONIC ................5-89
VARIATION ADJUSTMENT, STANDARD PROCEDURE - COMPASS ...............8M-5
VEHICLE DOES NOT FILL - DIAGNOSIS AND TESTING ....................... 25-17
VEHICLE EMISSION CONTROL INFORMATION LABEL, DESCRIPTION ......25-1
VEHICLE IDENTIFICATION - DESCRIPTION ........................ 23-1
VEHICLE INFO CENTER - DESCRIPTION, ELECTRONIC ........................ 8M-7
VEHICLE INFO CENTER - OPERATION, ELECTRONIC ........................ 8M-7
VEHICLE INFORMATION CENTER, DIAGNOSIS AND TESTING -
ELECTRONIC ........................ 8M-8
VEHICLE INFORMATION CENTER PROGRAMMING, STANDARD
PROCEDURE - ELECTRONIC ............8M-8
VEHICLE THEFT SECURITY - DESCRIPTION ........................ 8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
VENT WINDOW MOTOR, DIAGNOSIS AND TESTING ....................... 8N-62
VERIFICATION - STANDARD PROCEDURE, VALVE TIMING ...........9-155
VIBRATION - DIAGNOSIS AND TESTING, TIRE AND WHEEL ..................... 22-1
VIBRATION DAMPER - INSTALLATION ....9-132,
9-49
VIBRATION DAMPER - REMOVAL ....9-132,9-48
VIDEO SCREEN - DESCRIPTION .........8A-20
VIDEO SCREEN - INSTALLATION ........8A-20
VIDEO SCREEN - OPERATION ...........8A-20
VIDEO SCREEN - REMOVAL ............8A-20
VIEW MIRROR - INSTALLATION, REAR . . . 23-97
VIEW MIRROR - INSTALLATION, SIDE ....23-60
VIEW MIRROR - REMOVAL, REAR .......23-97
VIEW MIRROR - REMOVAL, SIDE ........23-60
VISOR - INSTALLATION, SUN ...........23-99
VISOR - REMOVAL, SUN ...............23-99
VISOR SUPPORT - INSTALLATION, SUN . . . 23-99
VISOR SUPPORT - REMOVAL, SUN ......23-99
VOLT SUPPLY - PCM OUTPUT - OPERATION, 5 ....................... 8E-15
VOLTAGE DROP - STANDARD PROCEDURE, TESTING FOR A .......8W-01-10
VOLTAGE POTENTIAL - STANDARD PROCEDURE, TESTING OF ...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION ....8F-30
VOLTAGE REGULATOR - OPERATION .....8F-30
VOLTAGE TEST, STANDARD PROCEDURE - OPEN-CIRCUIT ..................... 8F-13
VTSS/SKIS INDICATOR LAMP - DESCRIPTION ........................ 8Q-8
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

VTSS/SKIS INDICATOR LAMP -OPERATION .......................... 8Q-8
WARNING - A/C SYSTEM ..............24-66
WARNING - ENGINE COOLING SYSTEM . . . 24-65
WARNING - INSTALLATION ............23-162
WARNING - INSTALLATION .............19-16
WARNING - REMOVAL ...............23-161
WARNING - REMOVAL ................19-11
WARNING - SAFETY PRECAUTIONS AND WARNINGS .......................... 23-1
WARNING - WARNINGS ................8O-5
WARNING - WARNINGS AND CAUTIONS . . 19-10, 19-26
WARNING - WINDSHIELD SAFETY PRECAUTIONS ...................... 23-161
WARNING, CHIME/BUZZER ..............8B-2
WARNING, DESCRIPTION ................5-4
WARNING, DESCRIPTION ..............19-37
WARNING, LAMPS/LIGHTING - EXTERIOR ........................... 8L-3
WARNING, OPERATION ...............24-114
WARNINGS AND CAUTIONS, WARNING . . 19-10, 19-26
WARNINGS, GENERAL ..............8W-01-7
WARNINGS, WARNING .................8O-5
WARNINGS, WARNING - SAFETY PRECAUTIONS ........................ 23-1
WASHER FLUID LEVEL SWITCH - INSTALLATION ...................... 8R-11
WASHER FLUID LEVEL SWITCH - REMOVAL .......................... 8R-11
WASHER HOSES - INSTALLATION .......8R-12
WASHER HOSES - REMOVAL ...........8R-11
WASHER PUMP MOTOR - INSTALLATION . 8R-12
WASHER PUMP MOTOR - REMOVAL .....8R-12
WASHER RESERVOIR - INSTALLATION . . . 8R-13
WASHER RESERVOIR - REMOVAL .......8R-12
WASHER SYSTEM - DIAGNOSIS AND TESTING ............................ 8R-5
WATER CHANNEL - INSTALLATION ......23-174
WATER CHANNEL - REMOVAL .........23-174
WATER LEAKS, DIAGNOSIS AND TESTING ............................ 23-1
WATER PUMP - 2.4L - CLEANING ........7-32
WATER PUMP - 2.4L - DESCRIPTION ......7-32
WATER PUMP - 2.4L - INSPECTION .......7-32
WATER PUMP - 2.4L - INSTALLATION .....7-32
WATER PUMP - 2.4L - REMOVAL .........7-32
WATER PUMP - 3.3/3.8L - CLEANING .....7-35
WATER PUMP - 3.3/3.8L - DESCRIPTION . . . 7-34
WATER PUMP - 3.3/3.8L - INSPECTION ....7-35
WATER PUMP - 3.3/3.8L - INSTALLATION ........................ 7-35
WATER PUMP - 3.3/3.8L - REMOVAL ......7-34
WATER PUMP INLET TUBE - 2.4L - DESCRIPTION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - INSTALLATION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - REMOVAL ........................... 7-36
WATER PUMP INLET TUBE - 3.3/3.8L - INSTALLATION ........................ 7-37
WATER PUMP INLET TUBE - 3.3/3.8L - REMOVAL ........................... 7-37
WATERSHIELD - INSTALLATION .........23-21
WATERSHIELD - REMOVAL .............23-21
WEAR - STANDARD PROCEDURE, MEASURING TIMING CHAIN ............9-155
WEAR INDICATORS - DIAGNOSIS AND TESTING, TREAD ..................... 22-16
WEAR PATTERNS - DIAGNOSIS AND TESTING, TIRE ...................... 22-16
WEATHERSTRIP - INSTALLATION, FRONT DOOR ............................ 23-168
WEATHERSTRIP - INSTALLATION, FRONT DOOR GLASS RUN .................. 23-166
WEATHERSTRIP - INSTALLATION, SLIDING DOOR ..................... 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR ............................ 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR GLASS RUN .................. 23-166WEATHERSTRIP - REMOVAL, SLIDING
DOOR ............................ 23-168
WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION, SEAT .........8O-43
WEIGHT BLADDER & PRESSURE SENSOR - OPERATION, SEAT ...........8O-44
WELD LOCATIONS - FOLD-IN-FLOOR - SPECIFICATIONS .................... 23-350
WELD LOCATIONS - SPECIFICATIONS . . . 23-234
WHEEL - DESCRIPTION ...............22-18
WHEEL - INSPECTION, TONE ............5-94
WHEEL - INSTALLATION, STEERING ......19-24
WHEEL - REMOVAL, STEERING .........19-23
WHEEL ALIGNMENT - DESCRIPTION ......2-47
WHEEL ALIGNMENT - STANDARD PROCEDURE ......................... 2-52
WHEEL ALIGNMENT, SPECIFICATIONS .....2-56
WHEEL AND WHEEL TRIM CARE, CLEANING .......................... 22-19
WHEEL ASSEMBLY (ALUMINUM WHEEL) - INSTALLATION, TIRE .................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL) - REMOVAL, TIRE ..................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - INSTALLATION, TIRE ................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - REMOVAL, TIRE ...................... 22-8
WHEEL BALANCE - STANDARD PROCEDURE, TIRE .................... 22-5
WHEEL COVER - DESCRIPTION .........22-19
WHEEL COVER - INSTALLATION ..........22-20
WHEEL COVER - REMOVAL ............22-19
WHEEL CYLINDERS - INSPECTION ........5-62
WHEEL CYLINDERS - INSTALLATION ......5-62
WHEEL CYLINDERS - REMOVAL ..........5-62
WHEEL INSPECTION - DIAGNOSIS AND TESTING ........................... 22-19
WHEEL MATCH MOUNTING - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL MOUNTING STUDS - FRONT - INSTALLATION ....................... 22-21
WHEEL MOUNTING STUDS - FRONT - REMOVAL .......................... 22-21
WHEEL MOUNTING STUDS - REAR - INSTALLATION ....................... 22-22
WHEEL MOUNTING STUDS - REAR - REMOVAL .......................... 22-22
WHEEL ROTATION - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL RUNOUT, SPECIFICATIONS - TONE ............................... 5-91
WHEEL, SPECIFICATIONS ..............22-19
WHEEL SPEED SENSOR - AWD - INSTALLATION, REAR .................. 5-92
WHEEL SPEED SENSOR - AWD - REMOVAL, REAR ...................... 5-92
WHEEL SPEED SENSOR - FWD - INSTALLATION, REAR .................. 5-93
WHEEL SPEED SENSOR - FWD - REMOVAL, REAR ...................... 5-93
WHEEL SPEED SENSOR - INSTALLATION, FRONT .................5-92
WHEEL SPEED SENSOR - REMOVAL, FRONT .............................. 5-91
WHEEL SPEED SENSOR AIR GAP, SPECIFICATIONS ...................... 5-91
WHEEL TRIM CARE, CLEANING - WHEEL . . 22-19
WHEEL VIBRATION - DIAGNOSIS AND TESTING, TIRE ....................... 22-1
WHEELHOUSE SPLASH SHIELD - INSTALLATION, FRONT ................23-57
WHEELHOUSE SPLASH SHIELD - REMOVAL, FRONT .................... 23-57
WIND DEFLECTOR - INSTALLATION .....23-174
WIND DEFLECTOR - REMOVAL .........23-174
WIND NOISE, DIAGNOSIS AND TESTING . . . 23-2
WINDOW - INSTALLATION, QUARTER . . . 23-164
WINDOW - REMOVAL, QUARTER .......23-164
WINDOW CRANK - INSTALLATION .......23-21
WINDOW CRANK - REMOVAL ...........23-21
WINDOW DEFOGGER RELAY - DESCRIPTION, REAR .................. 8G-3WINDOW DEFOGGER RELAY -
INSTALLATION, REAR .................. 8G-4
WINDOW DEFOGGER RELAY - OPERATION, REAR .................... 8G-3
WINDOW DEFOGGER RELAY - REMOVAL, REAR ..................... 8G-4
WINDOW DEFOGGER SWITCH - DESCRIPTION, REAR .................. 8G-4
WINDOW DEFOGGER SWITCH - OPERATION, REAR .................... 8G-4
WINDOW MOTOR - REMOVAL ..........8N-62
WINDOW MOTOR, DIAGNOSIS AND TESTING - VENT ..................... 8N-62
WINDOW REGULATOR - MANUAL - INSTALLATION ....................... 23-23
WINDOW REGULATOR - MANUAL - REMOVAL .......................... 23-22
WINDOW REGULATOR - POWER - INSTALLATION ....................... 23-22
WINDOW REGULATOR - POWER - REMOVAL .......................... 23-22
WINDOW SWITCH, DIAGNOSIS AND TESTING ........................... 8N-63
WINDOWS - DESCRIPTION, POWER .....8N-61
WINDOWS - OPERATION, POWER .......8N-61
WINDOWS, DIAGNOSIS AND TESTING - POWER ............................ 8N-61
WINDSHIELD - DESCRIPTION ..........23-161
WINDSHIELD SAFETY PRECAUTIONS, WARNING ......................... 23-161
WIPER ARM - INSTALLATION, REAR .....8R-10
WIPER ARM - REMOVAL, REAR ..........8R-10
WIPER ARM ALIGNMENT - STANDARD PROCEDURE, FRONT .................. 8R-9
WIPER ARMS - INSTALLATION, FRONT ....8R-9
WIPER ARMS - REMOVAL, FRONT ........8R-9
WIPER BLADES - CLEANING ...........8R-13
WIPER BLADES - INSTALLATION ........8R-13
WIPER BLADES - REMOVAL ............8R-13
WIPER LINKAGE - INSTALLATION .......8R-14
WIPER LINKAGE - REMOVAL ...........8R-13
WIPER MODULE - INSTALLATION .......8R-14
WIPER MODULE - REMOVAL ...........8R-14
WIPER MOTOR - INSTALLATION, FRONT . . 8R-10
WIPER MOTOR - INSTALLATION, REAR . . . 8R-10
WIPER MOTOR - REMOVAL, FRONT ......8R-9
WIPER MOTOR - REMOVAL, REAR ......8R-10
WIPER SYSTEM - DIAGNOSIS AND TESTING, FRONT ..................... 8R-2
WIPER SYSTEM - DIAGNOSIS AND TESTING, REAR ...................... 8R-4
WIPERS/WASHERS - DESCRIPTION .......8R-1
WIPERS/WASHERS - OPERATION ........8R-2
WIPER/WASHER SWITCH - DESCRIPTION, REAR .................8R-10
WIPER/WASHER SWITCH - DIAGNOSIS AND TESTING, FRONT .................8R-2
WIPER/WASHER SWITCH - OPERATION, REAR .............................. 8R-11
WIRE SPLICING - STANDARD PROCEDURE .....................8W -01-15
WIRING - INSTALLATION, HEATER ......24-122
WIRING - REMOVAL, HEATER ..........24-122
WIRING DIAGRAMS - DESCRIPTION, HOW TO USE .....................8W -01-1
WIRING HARNESS - DESCRIPTION ......8N-59
WIRING HARNESS - DIAGNOSIS AND TESTING .........................8W -01-7
WIRING HARNESS - INSTALLATION ......8N-59
WIRING HARNESS - OPERATION ........8N-59
WIRING HARNESS - REMOVAL .........8N-59
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD PROCEDURE, REPAIR OF DAMAGED
OR............................. 9-10,9-88
ZONE, DESCRIPTION - MANUAL DUAL .....24-2
ZONE, DESCRIPTION - MANUAL SINGLE . . . 24-2
ZONE, DESCRIPTION - MANUAL THREE ....24-2
ZONE, OPERATION - MANUAL DUAL ......24-5
ZONE, OPERATION - MANUAL SINGLE .....24-4
ZONE, OPERATION - MANUAL THREE .....24-5
RS INDEX35
Description Group-Page Description Group-Page Description Group-Page