remote control CHRYSLER CARAVAN 2005 Repair Manual

INSTRUMENT PANEL OUTLETS
(1) Using a trim stick or another suitable wide
flat-bladed tool, gently pry the outer perimeter of the
instrument panel outlet away from the instrument
panel top pad until the snap features on the outlet
are released (Fig. 5).
(2) Remove the instrument panel outlet from the
panel duct opening in the instrument panel top pad.
INSTALLATION
FRONT CENTER BEZEL OUTLETS
(1) Position the center bezel outlets and housing
onto the center bezel as a unit.
(2) Engage the retainer features on the top of the
outlet housing with their receptacles at the top of the
center bezel, then roll the bottom of the outlet hous-
ing downwards towards the center bezel.
(3) Install the three screws that secure the bottom
of the outlet housing to the center bezel. Tighten the
screws to 2 N´m (17 in. lbs.).
(4) If the vehicle is equipped with the optional
ATC system, reconnect the ATC remote infrared tem-
perature sensor jumper harness to the sensor connec-
tor receptacle located on the bottom of the center
outlet housing.
(5) Reinstall the center bezel onto the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL - INSTAL-
LATION).
(6) Reconnect the battery negative cable.
FRONT DEMISTER OUTLETS
(1) Position the demister outlet over the demister
duct opening in the instrument panel top pad.(2) Using hand pressure, press the demister outlet
firmly and evenly into the instrument panel top pad
opening until the snap features on the outlet are
fully engaged.
INSTRUMENT PANEL OUTLETS
(1) Position the instrument panel outlet into the
panel duct opening in the instrument panel top pad.
(2) Using hand pressure, press the instrument
panel outlet firmly and evenly into the instrument
panel top pad opening until the snap features on the
outlet are fully engaged.
BLOWER MOTOR
DESCRIPTION
The blower motor is a 12-volt, Direct Current (DC)
motor with a squirrel cage-type blower wheel that is
secured to the blower motor shaft (Fig. 6). The
blower motor and wheel are located near the passen-
ger side end of the HVAC housing in the passenger
compartment below the instrument panel. The
blower motor and blower motor wheel are factory bal-
anced and cannot be adjusted or repaired. If faulty or
damaged, the blower motor and blower wheel must
be replaced as an assembly.
OPERATION
On models equipped with the manual heater-A/C
system, the blower motor will operate whenever the
ignition switch is in the On position and the blower
control switch is in any position except Off. On mod-
els equipped with the Automatic Temperature Con-
trol (ATC) system, the blower motor will operate
Fig. 5 Instrument Panel Outlet - Left Side Shown
1 - INSTRUMENT PANEL TOP PAD
2 - INSTRUMENT PANEL OUTLET
3 - TRIM STICK
Fig. 6 Blower Motor
1 - BLOWER MOTOR
2 - RUBBER GROMMET
3 - BLOWER MOTOR CONNECTOR
4 - MOUNTING TABS
RSDISTRIBUTION - FRONT24-45
AIR OUTLETS (Continued)

ENGINE OIL PRESSURE - DIAGNOSISAND TESTING, CHECKING ...............9-53
ENGINE, SPECIAL TOOLS - 2.4L ..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L .......9-98
ENGINE, SPECIFICATIONS - 3.3/3.8L ......9-93
ENGINE SPEED SENSOR - DESCRIPTION . . 14-30
ENGINE SPEED SENSOR - OPERATION ....14-30
ENGINE, STANDARD PROCEDURE - HYDROSTATIC LOCKED .............9-10,9-87
ENGINES - DESCRIPTION, ENGINE OIL - DIESEL ..............................0-6
ENGINES - EXPORT - DESCRIPTION, DIESEL ............................. 0-21
ENGINES, INSTALLATION - 2.4L/3.3L/ 3.8L ............................... 24-77
ENGINES, INSTALLATION - 2.5L/2.8L DIESEL ............................ 24-78
ENGINES, REMOVAL - 2.4L/3.3L/3.8L .....24-76
ENGINES, REMOVAL - 2.5L/2.8L DIESEL . . 24-77
ENTRY MODULE - DESCRIPTION, SENTRY KEY REMOTE .................8Q-3
ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-5
ENTRY MODULE - INSTALLATION, SENTRY KEY REMOTE .................8Q-6
ENTRY MODULE - OPERATION, SENTRY KEY REMOTE ........................ 8Q-4
ENTRY MODULE - REMOVAL, SENTRY KEY REMOTE ........................ 8Q-6
ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-3
ENTRY TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS .................. 8N-24
ENTRY TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ........................... 8N-24
EQUIPMENT, STANDARD PROCEDURE - REFRIGERANT SYSTEM SERVICE ........24-69
ERASING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
EVACUATE, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-70
EVAP CANISTER - INSTALLATION, REAR . . 25-21
EVAP CANISTER - REMOVAL, REAR ......25-20
EVAPORATION CONTROL SYSTEM - OPERATION ......................... 25-11
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-98
EVAPORATOR - INSTALLATION, A/C ......24-81
EVAPORATOR - OPERATION, A/C . . . 24-80,24-98
EVAPORATOR - REMOVAL, A/C ..........24-81
EVAPORATOR, INSTALLATION - REAR A/C............................... 24-100
EVAPORATOR LINE EXTENSION, INSTALLATION - REAR A/C ............24-100
EVAPORATOR LINE EXTENSION, REMOVAL - REAR A/C .................24-99
EVAPORATOR, REMOVAL - REAR A/C .....24-98
EVAPORATOR TEMPERATURE SENSOR - DESCRIPTION ....................... 24-26
EVAPORATOR TEMPERATURE SENSOR - OPERATION ......................... 24-27
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-13
EVAP/PURGE SOLENOID - INSTALLATION . 25-13
EVAP/PURGE SOLENOID - OPERATION ....25-13
EVAP/PURGE SOLENOID - REMOVAL .....25-13
EXCESSIVE EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING ..............11-2
EXHAUST MANIFOLD - CLEANING ........9-63
EXHAUST MANIFOLD - INSPECTION .......9-63
EXHAUST MANIFOLD - INSTALLATION .....9-63
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-154
EXHAUST MANIFOLD - LEFT - INSPECTION ........................ 9-155
EXHAUST MANIFOLD - LEFT - INSTALLATION ....................... 9-155
EXHAUST MANIFOLD - LEFT - REMOVAL . . 9-154
EXHAUST MANIFOLD - REMOVAL .........9-63
EXHAUST MANIFOLD - RIGHT - CLEANING .......................... 9-153
EXHAUST MANIFOLD - RIGHT - INSPECTION ........................ 9-153
EXHAUST MANIFOLD - RIGHT - INSTALLATION ....................... 9-153
EXHAUST MANIFOLD - RIGHT - REMOVAL .......................... 9-152
EXHAUST SYSTEM - DESCRIPTION .......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING, EXCESSIVE ..............11-2EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING .............11-2
EXHAUST SYSTEM, SPECIAL TOOLS ......11-4
EXHAUST TUBE - INSTALLATION .......24-116
EXHAUST TUBE - REMOVAL ...........24-116
EXHAUSTER - DESCRIPTION, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXHAUSTER - INSTALLATION, REAR QUARTER PANEL/FENDER AIR ..........23-60
EXHAUSTER - REMOVAL, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXPANSION VALVE - DESCRIPTION ......24-81
EXPANSION VALVE - DESCRIPTION, A/C . 24-100
EXPANSION VALVE - OPERATION ........24-81
EXPANSION VALVE - OPERATION, A/C . . . 24-100
EXPANSION VALVE, DIAGNOSIS AND TESTING - FRONT A/C .................24-82
EXPANSION VALVE, DIAGNOSIS AND TESTING - REAR A/C .................24-101
EXPORT - ANTENNA MODULE ..........8A-10
EXPORT - BRAKE ROTOR ...............5-60
EXPORT - DESCRIPTION ................5-63
EXPORT - DESCRIPTION ................0-13
EXPORT - DESCRIPTION ................2-10
EXPORT - DESCRIPTION, ANTENNA MODULE ........................... 8A-10
EXPORT - DESCRIPTION, DIESEL ENGINES ............................ 0-21
EXPORT - DESCRIPTION, DOOR CYLINDER LOCK SWITCH ...............8N-22
EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ANTENNA ............8A-13
EXPORT - DOOR CYLINDER LOCK SWITCH ............................ 8N-22
EXPORT - INSTALLATION ...............5-68
EXPORT - INSTALLATION ...............2-11
EXPORT - INSTALLATION, HEADLAMP UNIT .............................. 8L-17
EXPORT - INSTALLATION, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-30
EXPORT - OPERATION, ANTENNA MODULE ........................... 8A-10
EXPORT - OPERATION, DOOR CYLINDER LOCK SWITCH ....................... 8N-22
EXPORT - OPERATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - OPERATION, QUARTER GLASS INTEGRAL ANTENNA .................. 8A-13
EXPORT - QUARTER GLASS INTEGRAL ANTENNA .......................... 8A-13
EXPORT - REMOVAL ................... 5-67
EXPORT - REMOVAL ................... 2-11
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - REMOVAL, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ALIGNMENT ......8L-9
EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT ALIGNMENT ..........8L-15
EXTENSION, INSTALLATION - REAR A/C EVAPORATOR LINE .................. 24-100
EXTENSION, REMOVAL - REAR A/C EVAPORATOR LINE ................... 24-99
EXTENSION TRIM - INSTALLATION, A-PILLAR LOWER .................... 23-79
EXTENSION TRIM - REMOVAL, A-PILLAR LOWER ............................ 23-79
EXTERIOR - DESCRIPTION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - OPERATION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - WARNING, LAMPS/ LIGHTING ........................... 8L-3
EXTERIOR HANDLE - INSTALLATION .....23-22,
23-40
EXTERIOR HANDLE - REMOVAL ....23-21,23-40
EXTERIOR HANDLE SWITCH - DESCRIPTION ....................... 8N-10
EXTERIOR HANDLE SWITCH - INSTALLATION ...................... 8N-10
EXTERIOR HANDLE SWITCH - OPERATION ......................... 8N-10EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-10
EXTERIOR LAMPS, SPECIFICATIONS
......8L-3
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - REMOVAL ................23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - REMOVAL ................23-51
FACTOR SETTING - STANDARD PROCEDURE, PINION .................8E-15
FAILED PARK SWITCH - DIAGNOSIS AND TESTING ............................ 8R-2
FAN - DESCRIPTION, RADIATOR ..........7-29
FAN - INSTALLATION, RADIATOR .........7-30
FAN - OPERATION, RADIATOR ...........7-29
FAN - REMOVAL, RADIATOR .............7-30
FAN MOTOR - DIAGNOSIS AND TESTING, RADIATOR ................... 7-30
FAN RELAY - DESCRIPTION, RADIATOR ....7-31
FAN RELAY - INSTALLATION, RADIATOR . . . 7-31
FAN RELAY - OPERATION, RADIATOR ......7-31
FAN RELAY - REMOVAL, RADIATOR .......7-31
FASCIA - INSTALLATION, FRONT .........13-1
FASCIA - INSTALLATION, REAR ..........13-4
FASCIA - REMOVAL, FRONT .............13-1
FASCIA - REMOVAL, REAR ..............13-4
FASCIA - SCUFF PAD - INSTALLATION, REAR ............................... 13-5
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-5
FASTENER TORQUE, SPECIFICATIONS - ABS ................................ 5-91
FASTENER TORQUE, SPECIFICATIONS - BRAKE ...............................5-9
FASTENER TORQUE, SPECIFICATIONS - COLUMN ........................... 19-17
FASTENER TORQUE, SPECIFICATIONS - FRONT SUSPENSION ...................2-3
FASTENER TORQUE, SPECIFICATIONS - POWER STEERING .................... 19-9
FASTENER TORQUE, SPECIFICATIONS - REAR SUSPENSION ................... 2-28
FEED CIRCUIT RESISTANCE TEST - DIAGNOSIS AND TESTING ..............8F-35
FEED CIRCUIT TEST - DIAGNOSIS AND TESTING ........................... 8F-36
FENDER - INSTALLATION, FRONT ........23-52
FENDER - REMOVAL, FRONT ...........23-51
FFV REPLACEMENT PARTS - DESCRIPTION ........................ 14-2
FILL - DIAGNOSIS AND TESTING, VEHICLE DOES NOT .................. 25-17
FILL DOOR - INSTALLATION, FUEL .......23-52
FILL DOOR - REMOVAL, FUEL ..........23-52
FILL DOOR BLOCKER LATCH - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL .................23-54
FILL DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL ..................... 23-54
FILL/CHECK LOCATIONS - DESCRIPTION, FLUID ...............................0-7
FILLER CAP - DESCRIPTION, FUEL .......25-13
FILLER CAP - OPERATION, FUEL ........25-13
FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP TO ............7-28
FILLER TUBE - INSTALLATION, FUEL TANK .............................. 14-17
FILLER TUBE - REMOVAL, FUEL TANK ....14-16
FILLING - STANDARD PROCEDURE, COOLING SYSTEM .....................7-4
FILLING, STANDARD PROCEDURE - REAR HEATER CORE .................24-102
FILTER - DESCRIPTION, AIR ............24-42
FILTER - DESCRIPTION, OIL .............9-54
FILTER - INSTALLATION, AIR ...........24-43
FILTER - INSTALLATION, INLET ..........14-17
FILTER - INSTALLATION, OIL .......9-141,9-54
FILTER - REMOVAL, AIR ...............24-42
FILTER - REMOVAL, INLET .............14-17
FILTER - REMOVAL, OIL ...........9-141,9-54
12 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

INTERMEDIATE - INSTALLATION, CABLE- PARKING BRAKE ..................... 5-69
INTERMEDIATE - REMOVAL, CABLE - PARKING BRAKE ...................... 5-69
INTERNATIONAL SYMBOLS - DESCRIPTION .........................0-1
INTRODUCTION - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-3,9-78
IOD FUSE - DESCRIPTION ...........8W-97-3
IOD FUSE - OPERATION .............8W-97-3
JOINT - DESCRIPTION, LOWER BALL ......2-10
JOINT - DIAGNOSIS AND TESTING, LOWER BALL ........................ 2-10
JOINT - OPERATION, LOWER BALL .......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-60
JOINT MOLDING - REMOVAL, ROOF ......23-60
JOUNCE BUMPER - DESCRIPTION ........2-35
JOUNCE BUMPER - OPERATION ..........2-35
JUMP STARTING - STANDARD PROCEDURE ......................... 0-25
JUNCTION BLOCK - DESCRIPTION, NON-ABS ............................ 5-33
JUNCTION BLOCK - INSTALLATION, NON-ABS ............................ 5-34
JUNCTION BLOCK - OPERATION, NON-ABS ............................ 5-33
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-34
KEY - DESCRIPTION, TRANSPONDER .....8Q-6
KEY - OPERATION, TRANSPONDER .......8Q-6
KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........23-90
KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ...........23-90
KEY REMOTE ENTRY MODULE - DESCRIPTION, SENTRY ................8Q-3
KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY .......8Q-5
KEY REMOTE ENTRY MODULE - INSTALLATION, SENTRY ................8Q-6
KEY REMOTE ENTRY MODULE - OPERATION, SENTRY .................. 8Q-4
KEY REMOTE ENTRY MODULE - REMOVAL, SENTRY ................... 8Q-6
KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY .......8Q-3
KEYLESS ENTRY TRANSMITTER, DIAGNOSIS AND TESTING .............8N-24
KEYLESS ENTRY TRANSMITTER PROGRAMMING - STANDARD
PROCEDURE, REMOTE ................8N-24
KEY/LOCK CYLINDER - DESCRIPTION ....19-20
KEY/LOCK CYLINDER - INSTALLATION ....19-20
KEY/LOCK CYLINDER - OPERATION ......19-20
KEY/LOCK CYLINDER - REMOVAL .......19-20
KNEE - INSTALLATION, BLOCKER- INFLATABLE ......................... 23-75
KNEE - REMOVAL, BLOCKER- INFLATABLE ......................... 23-75
KNEE BLOCKER AIRBAG - DESCRIPTION . . 8O-22
KNEE BLOCKER AIRBAG - INSTALLATION . 8O-23
KNEE BLOCKER AIRBAG - OPERATION . . . 8O-22
KNEE BLOCKER AIRBAG - REMOVAL .....8O-23
KNOB - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
KNOB - REMOVAL, SEAT BELT HEIGHT ADJUSTER ......................... 8O-38
KNOCK SENSOR - DESCRIPTION ..........8I-8
KNOCK SENSOR - OPERATION ...........8I-8
KNUCKLE - DESCRIPTION ................2-6
KNUCKLE - INSPECTION, STEERING ........2-9
KNUCKLE - INSTALLATION, STEERING ......2-9
KNUCKLE - OPERATION .................2-7
KNUCKLE - REMOVAL, STEERING .........2-7
LABEL, DESCRIPTION - VEHICLE EMISSION CONTROL INFORMATION .......25-1
LAMP - DESCRIPTION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - DIAGNOSIS AND TESTING, FRONT FOG .......................... 8L-7
LAMP - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP - INSTALLATION, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - INSTALLATION, COURTESY ......8L-21
LAMP - INSTALLATION, DOME/CARGO ....8L-22
LAMP - INSTALLATION, FRONT FOG .......8L-8
LAMP - INSTALLATION, LICENSE ........8L-17
LAMP - INSTALLATION, LIFTGATE .......8L-22 LAMP - INSTALLATION, PARK/TURN
SIGNAL ............................ 8L-18
LAMP - INSTALLATION, READING ........8L-23
LAMP - INSTALLATION, TAIL ...........8L-19
LAMP - INSTALLATION, VANITY .........8L-24
LAMP - OPERATION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - REMOVAL, CENTER CONSOLE ....8L-21
LAMP - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - REMOVAL, COURTESY ..........8L-21
LAMP - REMOVAL, DOME/CARGO .......8L-22
LAMP - REMOVAL, FRONT FOG ..........8L-8
LAMP - REMOVAL, LICENSE ............8L-17
LAMP - REMOVAL, LIFTGATE ...........8L-22
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-18
LAMP - REMOVAL, READING ...........8L-22
LAMP - REMOVAL, TAIL ...............8L-18
LAMP - REMOVAL, VANITY .............8L-24
LAMP SWITCH - DESCRIPTION, BRAKE ....8L-4
LAMP SWITCH - DIAGNOSIS AND TESTING, BRAKE ...................... 8L-4
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - INSTALLATION, GLOVE BOX ............................... 8L-22
LAMP SWITCH - OPERATION, BRAKE ......8L-4
LAMP SWITCH - REMOVAL, BRAKE .......8L-5
LAMP SWITCH - REMOVAL, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - REMOVAL, GLOVE BOX . . 8L-22
LAMP UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP .................8L-6
LAMP UNIT - INSTALLATION, TAIL .......8L-19
LAMP UNIT - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP UNIT - REMOVAL, TAIL ...........8L-19
LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG .....8L-9
LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG ...............8L-9
LAMPS - INSTALLATION, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS - REMOVAL, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS, SPECIFICATIONS - EXTERIOR .....8L-3
LAMPS, SPECIFICATIONS - INTERIOR ....8L-20
LAMPS/LIGHTING - EXTERIOR - DESCRIPTION ........................ 8L-2
LAMPS/LIGHTING - EXTERIOR - OPERATION .......................... 8L-2
LAMPS/LIGHTING - EXTERIOR - WARNING ........................... 8L-3
LAP BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER .....23-157
LAP BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER .................. 23-157
LASH ADJUSTER NOISE DIAGNOSIS - DIAGNOSIS AND TESTING, HYDRAULIC ....9-34
LASH ADJUSTERS - INSTALLATION, HYDRAULIC .......................... 9-35
LASH ADJUSTERS - REMOVAL, HYDRAULIC .......................... 9-35
LATCH - DESCRIPTION ...........8N-12,8N-49
LATCH - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID ....23-90
LATCH - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID .................23-90
LATCH - INSTALLATION .....23-18,23-41,23-63
LATCH - INSTALLATION ..........8N-13,8N-50
LATCH - INSTALLATION, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH - INSTALLATION, GLOVE BOX .....23-66
LATCH - INSTALLATION, HOLD OPEN .....23-25
LATCH / LOCK ASSEMBLY - INSTALLATION ....................... 23-27
LATCH / LOCK ASSEMBLY - REMOVAL ....23-26
LATCH - OPERATION ............8N-12,8N-49
LATCH - REMOVAL .........23-18,23-41,23-63
LATCH - REMOVAL ..............8N-12,8N-49
LATCH - REMOVAL, FUEL FILL DOOR BLOCKER ........................... 23-53
LATCH - REMOVAL, GLOVE BOX .........23-66
LATCH - REMOVAL, HOLD OPEN ........23-25
LATCH ACTUATOR - DESCRIPTION ......8N-13
LATCH ACTUATOR - INSTALLATION ......8N-14
LATCH ACTUATOR - OPERATION ........8N-13 LATCH ACTUATOR - REMOVAL
..........8N-13
LATCH CABLE - INSTALLATION, HOLD OPEN .............................. 23-38
LATCH CABLE - REMOVAL, HOLD OPEN . . . 23-38
LATCH HANDLE - INSTALLATION, INSIDE . . 23-34
LATCH HANDLE - REMOVAL, INSIDE .....23-34
LATCH LOCKING LINK - INSTALLATION, SEAT RISER ........................ 23-151
LATCH LOCKING LINK - REMOVAL, SEAT RISER ............................ 23-151
LATCH RELEASE CABLE - INSTALLATION . . 23-64
LATCH RELEASE CABLE - REMOVAL .....23-63
LATCH STRIKER - INSTALLATION . . 23-19,23-42, 23-64
LATCH STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER .................23-53
LATCH STRIKER - INSTALLATION, GLOVE BOX ............................... 23-66
LATCH STRIKER - INSTALLATION, HOLD OPEN .............................. 23-26
LATCH STRIKER - INSTALLATION, REAR . . 23-29
LATCH STRIKER - REMOVAL . 23-19,23-41,23-64
LATCH STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH STRIKER - REMOVAL, GLOVE BOX ............................... 23-66
LATCH STRIKER - REMOVAL, HOLD OPEN .............................. 23-26
LATCH STRIKER - REMOVAL, REAR ......23-29
LEAD - DIAGNOSIS AND TESTING, TIRE/VEHICLE ......................... 22-14
LEAF SPRING FRONT - INSTALLATION, BUSHING ............................ 2-30
LEAF SPRING FRONT - REMOVAL, BUSHING ............................ 2-29
LEAK DETECTION ASSY - INSTALLATION, NATURAL VAC ....................... 25-14
LEAK DETECTION ASSY - REMOVAL, NATURAL VAC ....................... 25-14
LEAK DETECTION PUMP - INSTALLATION . 25-15
LEAK DETECTION PUMP - REMOVAL .....25-15
LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE OIL ...............9-8,9-84
LEAK REPAIRING - STANDARD PROCEDURE, TIRE ................... 22-17
LEAK TEST - DIAGNOSIS AND TESTING, COOLING SYSTEM .....................7-2
LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER HOUSING FLUID . . 21-154, 21-9
LEAKAGE TEST - DIAGNOSIS AND TESTING, CYLINDER COMBUSTION
PRESSURE ....................... 9-85,9-9
LEAKS - DIAGNOSIS AND TESTING, INTAKE MANIFOLD ...............9-147,9-60
LEAKS, DIAGNOSIS AND TESTING - REFRIGERANT SYSTEM ...............24-67
LEAKS, DIAGNOSIS AND TESTING - WATER ............................. 23-1
LEARN CYCLE, STANDARD PROCEDURE - POWER LIFTGATE ................... 8N-8
LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING DOOR ..............8N-48
LEARN PROCEDURE - STANDARD PROCEDURE, QUICK .................. 8E-15
LENS - INSTALLATION, CLUSTER ........8J-11
LENS - REMOVAL, CLUSTER ............8J-11
LEVEL AND CONDITION CHECK, STANDARD PROCEDURE - FLUID . . 21-230,21-82
LEVEL CHECK - STANDARD PROCEDURE, COOLANT .................7-4
LEVEL CHECK - STANDARD PROCEDURE, ENGINE OIL ..............9-140
LEVEL CHECK, STANDARD PROCEDURE - ENGINE OIL ........................ 9-54
LEVEL CHECKING - STANDARD PROCEDURE, BRAKE FLUID .............5-33
LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING FLUID . . . 19-44
LEVEL SENDING UNIT / SENSOR - DESCRIPTION, FUEL ................... 14-5
LEVEL SENDING UNIT / SENSOR - INSTALLATION, FUEL .................. 14-6
LEVEL SENDING UNIT / SENSOR - OPERATION, FUEL ..................... 14-5
LEVEL SENDING UNIT / SENSOR - REMOVAL, FUEL ...................... 14-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

LWB - INSTALLATION, SEAT BELT &RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC ..........8O-41
LWB - REMOVAL, SEAT BELT & RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC ..........8O-41
MACHINING - STANDARD PROCEDURE, BRAKE ROTOR ....................... 5-58
MAIN BEARING FITTING - STANDARD PROCEDURE ........................ 9-125
MAIN BEARINGS - INSTALLATION, CRANKSHAFT ....................... 9-127
MAIN BEARINGS - REMOVAL, CRANKSHAFT ....................... 9-127
MANAGER - DESCRIPTION, TASK ........25-25
MANAGER - OPERATION, TASK .........25-25
MANIFOLD - CLEANING, EXHAUST ........9-63
MANIFOLD - DESCRIPTION, INTAKE . . 9-147,9-60
MANIFOLD - INSPECTION, EXHAUST ......9-63
MANIFOLD - INSTALLATION, EXHAUST ....9-63
MANIFOLD - INSTALLATION, LOWER INTAKE ............................ 9-151
MANIFOLD - INSTALLATION, UPPER INTAKE ............................ 9-149
MANIFOLD - LEFT - CLEANING, EXHAUST ........................... 9-154
MANIFOLD - LEFT - INSPECTION, EXHAUST ........................... 9-155
MANIFOLD - LEFT - INSTALLATION, EXHAUST ........................... 9-155
MANIFOLD - LEFT - REMOVAL, EXHAUST . 9-154
MANIFOLD - LOWER - CLEANING, INTAKE ............................ 9-151
MANIFOLD - LOWER - INSPECTION, INTAKE ........................ 9-151,9-62
MANIFOLD - LOWER - INSTALLATION, INTAKE ............................. 9-62
MANIFOLD - LOWER - REMOVAL, INTAKE ............................. 9-62
MANIFOLD - REMOVAL, EXHAUST ........9-63
MANIFOLD - REMOVAL, LOWER INTAKE . . 9-150
MANIFOLD - REMOVAL, UPPER INTAKE . . . 9-148
MANIFOLD - RIGHT - CLEANING, EXHAUST ........................... 9-153
MANIFOLD - RIGHT - INSPECTION, EXHAUST ........................... 9-153
MANIFOLD - RIGHT - INSTALLATION, EXHAUST ........................... 9-153
MANIFOLD - RIGHT - REMOVAL, EXHAUST ........................... 9-152
MANIFOLD - UPPER - INSPECTION, INTAKE ............................. 9-61
MANIFOLD - UPPER - INSTALLATION, INTAKE ............................. 9-61
MANIFOLD - UPPER - REMOVAL, INTAKE . . 9-60
MANIFOLD LEAKS - DIAGNOSIS AND TESTING, INTAKE ................ 9-147,9-60
MANIFOLD STRIPPED THREAD REPAIR - STANDARD PROCEDURE ...............9-147
MANIFOLD VACUUM PORT REPAIR - STANDARD PROCEDURE, INTAKE ........9-148
MANUAL - INSTALLATION, WINDOW REGULATOR ........................ 23-23
MANUAL - OCS - INSTALLATION, FRONT SEAT RISER ........................ 23-123
MANUAL - OCS - REMOVAL, FRONT SEAT RISER ........................ 23-123
MANUAL - REMOVAL, WINDOW REGULATOR ........................ 23-22
MANUAL ADJUSTER - INSTALLATION, FRONT SEAT TRACK .................23-126
MANUAL ADJUSTER - REMOVAL, FRONT SEAT TRACK ....................... 23-125
MANUAL DUAL ZONE, DESCRIPTION ......24-2
MANUAL DUAL ZONE, OPERATION ........24-5
MANUAL SINGLE ZONE, DESCRIPTION ....24-2
MANUAL SINGLE ZONE, OPERATION ......24-4
MANUAL TEMPERATURE CONTROL SYSTEM, OPERATION ................24-113
MANUAL THREE ZONE, DESCRIPTION .....24-2
MANUAL THREE ZONE, OPERATION .......24-5
MAP SENSOR - DESCRIPTION ..........14-34
MAP SENSOR - OPERATION ............14-34
MASTER CYLINDER BLEEDING - STANDARD PROCEDURE ................5-36
MASTER CYLINDER (FLUID RESERVOIR) - ASSEMBLY ......................... 5-39MASTER CYLINDER (FLUID RESERVOIR)
- DISASSEMBLY ...................... 5-38
MATCH MOUNTING - STANDARD PROCEDURE, TIRE AND WHEEL ..........22-7
MATS - INSTALLATION, CARPETS AND FLOOR ............................. 23-81
MATS - REMOVAL, CARPETS AND FLOOR ............................. 23-81
MEASUREMENT - STANDARD PROCEDURE, CURB HEIGHT .............2-55
MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS - DIFFERENTIAL
BEARING PRELOAD ................... 21-79
MEASUREMENTS - SPECIFICATIONS, GAP AND FLUSH .................... 23-177
MEASURING BEARING CLEARANCE USING PLASTIGAGE - STANDARD
PROCEDURE ..................... 9-12,9-86
MEASURING CAMSHAFT END PLAY - STANDARD PROCEDURE ................9-29
MEASURING CONNECTING ROD BEARING CLEARANCE - STANDARD
PROCEDURE ........................ 9-123
MEASURING CRANKSHAFT END PLAY - STANDARD PROCEDURE ...............9-128
MEASURING TIMING CHAIN WEAR - STANDARD PROCEDURE ...............9-155
MECHANICAL - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-6,9-82
MECHANISM -SECOND ROW -FOLD-IN- FLOOR - INSTALLATION, SEAT
RECLINER/FORWARD FOLDING ........23-137
MECHANISM -SECOND ROW -FOLD-IN- FLOOR - REMOVAL, SEAT RECLINER/
FORWARD FOLDING .................23-137
MECHANISM -THIRD ROW -FOLD-IN- FLOOR - INSTALLATION, SEAT
RECLINER/FOLD FORWARD ...........23-160
MECHANISM -THIRD ROW -FOLD-IN- FLOOR - REMOVAL, SEAT RECLINER/
FOLD FORWARD .................... 23-160
MEMORIES, OPERATION - FUEL CORRECTION OR ADAPTIVE ............14-24
MEMORY SEAT/MIRROR MODULE - DESCRIPTION ........................ 8E-9
MEMORY SEAT/MIRROR MODULE - OPERATION .......................... 8E-9
MEMORY SEAT/MIRROR MODULE, DIAGNOSIS AND TESTING ..............8E-9
MEMORY SWITCH - DESCRIPTION ......8N-36
MEMORY SWITCH - OPERATION ........8N-36
MEMORY SWITCH, DIAGNOSIS AND TESTING ........................... 8N-37
MEMORY SYSTEM, DESCRIPTION .......8N-32
MEMORY SYSTEM, DIAGNOSIS AND TESTING ........................... 8N-33
MEMORY SYSTEM, OPERATION .........8N-33
MESSAGE CENTER - INSTALLATION ......8M-1
MESSAGE CENTER - REMOVAL ..........8M-1
MICRO 420 BATTERY TESTER, STANDARD PROCEDURE ...............8F-15
MINI-TRIP COMPUTER, DIAGNOSIS AND TESTING - COMPASS .................8M-10
MIRROR - DESCRIPTION, AUTOMATIC DAY / NIGHT ........................ 8N-28
MIRROR - INSTALLATION, GLASS- OUTSIDE REARVIEW .................. 23-61
MIRROR - INSTALLATION, REAR VIEW . . . 23-97
MIRROR - INSTALLATION, SIDE VIEW ....23-60
MIRROR - OPERATION, AUTOMATIC DAY / NIGHT ............................ 8N-28
MIRROR - REMOVAL, GLASS-OUTSIDE REARVIEW .......................... 23-61
MIRROR - REMOVAL, REAR VIEW .......23-97
MIRROR - REMOVAL, SIDE VIEW ........23-60
MIRROR - REMOVAL, SIDEVIEW ........8N-30
MIRROR, DIAGNOSIS AND TESTING - AUTOMATIC DAY / NIGHT ..............8N-28
MIRROR SWITCH - EXPORT - DESCRIPTION, POWER FOLDAWAY ......8N-29
MIRROR SWITCH - EXPORT - INSTALLATION, POWER FOLDAWAY ......8N-30
MIRROR SWITCH - EXPORT - OPERATION, POWER FOLDAWAY ........8N-29
MIRROR SWITCH - EXPORT - REMOVAL, POWER FOLDAWAY .................. 8N-29
MIRRORS - DESCRIPTION, HEATED .......8G-6
MIRRORS - DESCRIPTION, POWER ......8N-26 MIRRORS - OPERATION, HEATED
........8G-6
MIRRORS - OPERATION, POWER ........8N-26
MIRRORS, DIAGNOSIS AND TESTING - POWER ............................ 8N-27
MODE DOOR ACTUATOR - DESCRIPTION . . 24-29
MODE DOOR ACTUATOR - INSTALLATION ....................... 24-30
MODE DOOR ACTUATOR - OPERATION . . . 24-29
MODE DOOR ACTUATOR - REAR - DESCRIPTION ....................... 24-39
MODE DOOR ACTUATOR - REAR - INSTALLATION ....................... 24-40
MODE DOOR ACTUATOR - REAR - OPERATION ......................... 24-39
MODE DOOR ACTUATOR - REAR - REMOVAL .......................... 24-39
MODE DOOR ACTUATOR - REMOVAL .....24-29
MODE, OPERATION - DRB III TS TAT E
DISPLAY TEST ....................... 25-10
MODELS, INSTALLATION - RG ..........24-27
MODELS, INSTALLATION - RS ..........24-28
MODELS, REMOVAL - RG ..............24-27
MODELS, REMOVAL - RS ..............24-27
MODES OF OPERATION - OPERATION ....14-22
MODULE - BLOWER MOTOR - DESCRIPTION, POWER ................24-30
MODULE - BLOWER MOTOR - INSTALLATION, POWER ...............24-31
MODULE - BLOWER MOTOR - OPERATION, POWER .................. 24-30
MODULE - BLOWER MOTOR - REMOVAL, POWER ................... 24-30
MODULE - DESCRIPTION, BODY CONTROL ........................... 8E-2
MODULE - DESCRIPTION, FRONT CONTROL ........................... 8E-7
MODULE - DESCRIPTION, FUEL PUMP ....14-8
MODULE - DESCRIPTION, HEATED SEAT . . . 8E-8
MODULE - DESCRIPTION, INTEGRATED POWER ..........................8W -97-1
MODULE - DESCRIPTION, MEMORY SEAT/MIRROR ........................ 8E-9
MODULE - DESCRIPTION, OCCUPANT CLASSIFICATION ..................... 8O-25
MODULE - DESCRIPTION, PARK ASSIST . . . 8B-4
MODULE - DESCRIPTION, POWER LIFTGATE CONTROL .................. 8E-10
MODULE - DESCRIPTION, SENTRY KEY REMOTE ENTRY ...................... 8Q-3
MODULE - DESCRIPTION, SLIDING DOOR CONTROL ..................... 8E-18
MODULE - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE ENTRY ...........8Q-5
MODULE - EXPORT - DESCRIPTION, ANTENNA .......................... 8A-10
MODULE - EXPORT - OPERATION, ANTENNA .......................... 8A-10
MODULE - INSTALLATION, BODY CONTROL ........................... 8E-4
MODULE - INSTALLATION, HANDS FREE . . . 8T-3
MODULE - INSTALLATION, INTEGRATED POWER ..........................8W -97-2
MODULE - INSTALLATION, OCCUPANT CLASSIFICATION ..................... 8O-26
MODULE - INSTALLATION, PARK ASSIST . . 8B-6
MODULE - INSTALLATION, SENTRY KEY REMOTE ENTRY ...................... 8Q-6
MODULE - INSTALLATION, WIPER .......8R-14
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT CONTROL ........................... 8E-7
MODULE - OPERATION, FUEL PUMP ......14-9
MODULE - OPERATION, HEATED SEAT .....8E-8
MODULE - OPERATION, INTEGRATED POWER ..........................8W -97-2
MODULE - OPERATION, MEMORY SEAT/MIRROR ........................ 8E-9
MODULE - OPERATION, OCCUPANT CLASSIFICATION ..................... 8O-25
MODULE - OPERATION, PARK ASSIST .....8B-5
MODULE - OPERATION, POWER LIFTGATE CONTROL .................. 8E-10
MODULE - OPERATION, SENTRY KEY REMOTE ENTRY ...................... 8Q-4
MODULE - OPERATION, SLIDING DOOR CONTROL .......................... 8E-18
MODULE - REAR BLOWER MOTOR - DESCRIPTION, POWER ................24-40
20 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

MODULE - REAR BLOWER MOTOR -INSTALLATION, POWER ...............24-41
MODULE - REAR BLOWER MOTOR - OPERATION, POWER .................. 24-40
MODULE - REAR BLOWER MOTOR - REMOVAL, POWER ................... 24-41
MODULE - REMOVAL, BODY CONTROL ....8E-4
MODULE - REMOVAL, HANDS FREE .......8T-3
MODULE - REMOVAL, INTEGRATED POWER ..........................8W -97-2
MODULE - REMOVAL, OCCUPANT CLASSIFICATION ..................... 8O-26
MODULE - REMOVAL, PARK ASSIST ......8B-5
MODULE - REMOVAL, SENTRY KEY REMOTE ENTRY ...................... 8Q-6
MODULE - REMOVAL, WIPER ...........8R-14
MODULE, BENCH SEAT - REMOVAL, CHILD SEAT ........................ 23-104
MODULE, DIAGNOSIS AND TESTING - FRONT CONTROL ..................... 8E-7
MODULE, DIAGNOSIS AND TESTING - HEATED SEAT ........................ 8E-9
MODULE, DIAGNOSIS AND TESTING - MEMORY SEAT/MIRROR ................8E-9
MODULE, DIAGNOSIS AND TESTING - POWER LIFTGATE CONTROL ............8E-10
MODULE, DIAGNOSIS AND TESTING - SLIDING DOOR CONTROL ..............8E-18
MODULE, EXPORT - ANTENNA ..........8A-10
MODULE FLUIDS - DESCRIPTION, AWD REAR DRIVELINE ......................0-6
MOLDING - INSTALLATION, FRONT DOOR INNER BELT .................. 23-168
MOLDING - INSTALLATION, FRONT DOOR OUTER BELT .................. 23-167
MOLDING - INSTALLATION, ROOF JOINT . . 23-60
MOLDING - REMOVAL, FRONT DOOR INNER BELT ........................ 23-168
MOLDING - REMOVAL, FRONT DOOR OUTER BELT ....................... 23-167
MOLDING - REMOVAL, ROOF JOINT ......23-60
MOLDINGS - INSTALLATION, BODY SIDE . . 23-46
MOLDINGS - REMOVAL, BODY SIDE .....23-45
MONITORED COMPONENT - DESCRIPTION ........................ 25-1
MONITORED SYSTEMS - DESCRIPTION ....25-6
MONITORING - DESCRIPTION, TIRE PRESSURE .......................... 22-9
MONITORING - OPERATION, TIRE PRESSURE ......................... 22-10
MOTOR - DESCRIPTION, BLOWER . . 24-45,24-57
MOTOR - DESCRIPTION, IDLE AIR CONTROL .......................... 14-33
MOTOR - DESCRIPTION, LIFTGATE ......8N-15
MOTOR - DESCRIPTION, POWER MODULE - BLOWER .................. 24-30
MOTOR - DESCRIPTION, POWER MODULE - REAR BLOWER .............24-40
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-51
MOTOR - DIAGNOSIS AND TESTING, RADIATOR FAN ....................... 7-30
MOTOR - INSTALLATION, FRONT WIPER . . 8R-10
MOTOR - INSTALLATION, IDLE AIR CONTROL .......................... 14-33
MOTOR - INSTALLATION, LIFTGATE ......8N-16
MOTOR - INSTALLATION, POWER MODULE - BLOWER .................. 24-31
MOTOR - INSTALLATION, POWER MODULE - REAR BLOWER .............24-41
MOTOR - INSTALLATION, REAR WIPER . . . 8R-10
MOTOR - INSTALLATION, SLIDING DOOR . 8N-51
MOTOR - INSTALLATION, SLIDING DOOR LOCK .............................. 8N-25
MOTOR - INSTALLATION, SUNROOF .....23-174
MOTOR - INSTALLATION, WASHER PUMP ............................. 8R-12
MOTOR - OPERATION, BLOWER ....24-45,24-57
MOTOR - OPERATION, IDLE AIR CONTROL .......................... 14-33
MOTOR - OPERATION, LIFTGATE ........8N-15
MOTOR - OPERATION, POWER MODULE - BLOWER .......................... 24-30
MOTOR - OPERATION, POWER MODULE - REAR BLOWER ..................... 24-40
MOTOR - OPERATION, SLIDING DOOR . . . 8N-51
MOTOR - REMOVAL, FRONT WIPER ......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-33
MOTOR - REMOVAL, LIFTGATE .........8N-15MOTOR - REMOVAL, POWER MODULE -
BLOWER ........................... 24-30
MOTOR - REMOVAL, POWER MODULE - REAR BLOWER ...................... 24-41
MOTOR - REMOVAL, REAR WIPER ......8R-10
MOTOR - REMOVAL, SLIDING DOOR .....8N-51
MOTOR - REMOVAL, SLIDING DOOR LOCK .............................. 8N-25
MOTOR - REMOVAL, SUNROOF ........23-174
MOTOR - REMOVAL, WASHER PUMP ....8R-12
MOTOR - REMOVAL, WINDOW ..........8N-62
MOTOR, DIAGNOSIS AND TESTING - DOOR LOCK ........................ 8N-23
MOTOR, DIAGNOSIS AND TESTING - FRONT BLOWER ..................... 24-46
MOTOR, DIAGNOSIS AND TESTING - REAR BLOWER ...................... 24-58
MOTOR, DIAGNOSIS AND TESTING - VENT WINDOW ...................... 8N-62
MOTOR RELAY - DESCRIPTION, BLOWER ...................... 24-23,24-36
MOTOR RELAY - INSTALLATION, BLOWER ...................... 24-24,24-37
MOTOR RELAY - OPERATION, BLOWER . . 24-23, 24-36
MOTOR RELAY - REMOVAL, BLOWER ....24-24,
24-37
MOTOR RESISTOR BLOCK - DESCRIPTION, BLOWER ..........24-24,24-37
MOTOR RESISTOR BLOCK - OPERATION, BLOWER ...................... 24-24,24-37
MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING - FRONT BLOWER ........24-25
MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING - REAR BLOWER .........24-38
MOUNT - INSTALLATION, FRONT ....9-134,9-50
MOUNT - INSTALLATION, LEFT ......9-136,9-50
MOUNT - INSTALLATION, REAR .....9-137,9-52
MOUNT - INSTALLATION, RIGHT ....9-138,9-52
MOUNT - REMOVAL, FRONT ........9-134,9-50
MOUNT - REMOVAL, LEFT .........9-136,9-50
MOUNT - REMOVAL, REAR .........9-136,9-51
MOUNT - REMOVAL, RIGHT ........9-138,9-52
MOUNT BUSHINGS - INSTALLATION, FRONT CROSSMEMBER ...............13-17
MOUNT BUSHINGS - REMOVAL, FRONT CROSSMEMBER ..................... 13-17
MOUNTED STOP LAMP - INSTALLATION, CENTER HIGH ........................ 8L-6
MOUNTED STOP LAMP - REMOVAL, CENTER HIGH ........................ 8L-6
MOUNTED STOP LAMP UNIT - INSTALLATION, CENTER HIGH ...........8L-6
MOUNTED STOP LAMP UNIT - REMOVAL, CENTER HIGH ...............8L-6
MOUNTING - DESCRIPTION, ENGINE . 9-134,9-50
MOUNTING - STANDARD PROCEDURE, TIRE AND WHEEL MATCH ...............22-7
MOUNTING BRACKET, 2.4L ENGINE - A/C COMPRESSOR .................. 24-74,24-75
MOUNTING STUDS - FRONT - INSTALLATION, WHEEL ................22-21
MOUNTING STUDS - FRONT - REMOVAL, WHEEL ............................ 22-21
MOUNTING STUDS - REAR - INSTALLATION, WHEEL ................22-22
MOUNTING STUDS - REAR - REMOVAL, WHEEL ............................ 22-22
MOUNTS - FRONT - INSTALLATION, SPRING ............................. 2-43
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-42
MOUNTS - REAR - INSTALLATION, SPRING ............................. 2-43
MOUNTS - REAR - REMOVAL, SPRING ....2-43
MUFFLER - INSTALLATION ..............11-8
MUFFLER - REMOVAL ..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS AND TESTING ....................... 8L-18
MULTI-FUNCTION SWITCH - INSTALLATION ....................... 8L-18
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - ADHESIVE ATTACHED - INSTALLATION, EXTERIOR .............23-51
NAME PLATES - ADHESIVE ATTACHED - REMOVAL, EXTERIOR .................23-51
NAME PLATES - TAPE ATTACHED - INSTALLATION, EXTERIOR .............23-51NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR .................23-51
NATURAL VAC LEAK DETECTION ASSY - INSTALLATION ....................... 25-14
NATURAL VAC LEAK DETECTION ASSY - REMOVAL .......................... 25-14
NAVIGATION RADIO - INSTALLATION, ANTENNA .......................... 8A-11
NAVIGATION RADIO - REMOVAL, ANTENNA .......................... 8A-11
NAVIGATION/TELECOMMUNICATION - DESCRIPTION ........................8T-1
NAVIGATION/TELECOMMUNICATION - OPERATION ..........................8T-1
NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP TO FILLER ..............7-28
NGC CONTROLLER - REMOVAL .........8E-16
NIGHT MIRROR - DESCRIPTION, AUTOMATIC DAY ..................... 8N-28
NIGHT MIRROR - OPERATION, AUTOMATIC DAY ..................... 8N-28
NIGHT MIRROR, DIAGNOSIS AND TESTING - AUTOMATIC DAY ............8N-28
NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD ......23-143
NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD ...........23-143
NOISE - DIAGNOSIS AND TESTING, EXCESSIVE EXHAUST SYSTEM ...........11-2
NOISE - DIAGNOSIS AND TESTING, TIRE . . 22-14
NOISE DIAGNOSIS - DIAGNOSIS AND TESTING, HYDRAULIC LASH
ADJUSTER ........................... 9-34
NOISE, DIAGNOSIS AND TESTING - WIND ............................... 23-2
NOISE DIAGNOSIS, DIAGNOSIS AND TESTING - A/C COMPRESSOR ..........24-72
NOISE SUPPRESSION COMPONENTS - DESCRIPTION, RADIO .................8A-15
NOISE SUPPRESSION COMPONENTS - OPERATION, RADIO .................. 8A-15
NON-ABS JUNCTION BLOCK - DESCRIPTION ........................ 5-33
NON-ABS JUNCTION BLOCK - INSTALLATION ........................ 5-34
NON-ABS JUNCTION BLOCK - OPERATION .......................... 5-33
NON-ABS JUNCTION BLOCK - REMOVAL . . . 5-34
NON-MONITORED CIRCUITS, DESCRIPTION ........................ 25-5
NOT FILL - DIAGNOSIS AND TESTING, VEHICLE DOES ...................... 25-17
NVLD - FOLD-IN-FLOOR - INSTALLATION, WITH .................25-20
NVLD - FOLD-IN-FLOOR - REMOVAL, WITH .............................. 25-20
O2 SENSOR - DESCRIPTION ............14-36
O2 SENSOR - OPERATION .............14-36
OBTAINING DIAGNOSTIC TROUBLE CODES - STANDARD PROCEDURE .......8E-15
OCCUPANT CLASSIFICATION MODULE - DESCRIPTION ....................... 8O-25
OCCUPANT CLASSIFICATION MODULE - INSTALLATION ...................... 8O-26
OCCUPANT CLASSIFICATION MODULE - OPERATION ......................... 8O-25
OCCUPANT CLASSIFICATION MODULE - REMOVAL .......................... 8O-26
OCCUPANT RESTRAINT CONTROLLER - DESCRIPTION ....................... 8O-27
OCCUPANT RESTRAINT CONTROLLER - INSTALLATION ...................... 8O-29
OCCUPANT RESTRAINT CONTROLLER - OPERATION ......................... 8O-28
OCCUPANT RESTRAINT CONTROLLER - REMOVAL .......................... 8O-29
OCS - INSTALLATION, FRONT SEAT CUSHION .......................... 23-120
OCS - INSTALLATION, FRONT SEAT CUSHION SIDE COVER ...............23-122
OCS - INSTALLATION, FRONT SEAT RISER - MANUAL ................... 23-123
OCS - INSTALLATION, FRONT SEAT TRACK ADJUSTER/MANUAL ...........23-128
OCS - INSTALLATION, FRONT SEAT TRACK ADJUSTER/POWER ............23-125
OCS - INSTALLATION, FRONT SEAT TRACK REAR COVER .................23-129
RS INDEX21
Description Group-Page Description Group-Page Description Group-Page

RELIEF VALVE, OPERATION - HIGHPRESSURE ......................... 24-72
REMOTE ENTRY MODULE - DESCRIPTION, SENTRY KEY .............8Q-3
REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY KEY .............8Q-5
REMOTE ENTRY MODULE - INSTALLATION, SENTRY KEY ............8Q-6
REMOTE ENTRY MODULE - OPERATION, SENTRY KEY ......................... 8Q-4
REMOTE ENTRY MODULE - REMOVAL, SENTRY KEY ......................... 8Q-6
REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY KEY .............8Q-3
REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE ..............8N-24
REMOTE SWITCH, DIAGNOSIS AND TESTING ........................... 8N-30
REMOTE SWITCHES - DESCRIPTION .....8A-16
REMOTE SWITCHES - OPERATION .......8A-16
REMOTE SWITCHES, DIAGNOSIS AND TESTING ........................... 8A-16
REPAIR - DESCRIPTION, FRONT CRADLE CROSSMEMBER THREAD ..............13-14
REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD VACUUM PORT ......9-148
REPAIR - STANDARD PROCEDURE, MANIFOLD STRIPPED THREAD ..........9-147
REPAIR - STANDARD PROCEDURE, PLASTIC BODY PANEL .................23-3
REPAIR OF DAMAGED OR WORN THREADS - STANDARD PROCEDURE . . 9-10,9-88
REPAIR PROCEDURE, STANDARD PROCEDURE - GRID ................... 8G-5
REPAIRING - STANDARD PROCEDURE, TIRE LEAK .......................... 22-17
REQUIREMENTS - DESCRIPTION, FUEL .....0-4
REQUIREMENTS - DIESEL ENGINE - DESCRIPTION, FUEL ....................0-6
REQUIREMENTS, DESCRIPTION - ENGINE COOLING SYSTEM ..............24-1
RESERVOIR - DESCRIPTION, VACUUM ....8P-6
RESERVOIR - INSTALLATION, VACUUM ....8P-6
RESERVOIR - INSTALLATION, WASHER . . . 8R-13
RESERVOIR - OPERATION, VACUUM ......8P-6
RESERVOIR - REMOVAL, VACUUM ........8P-6
RESERVOIR - REMOVAL, WASHER ......8R-12
RESET - STANDARD PROCEDURE, PARKING BRAKE AUTOMATIC
ADJUSTER TENSION ................... 5-64
RESISTANCE, SPECIFICATIONS - SPARK PLUG CABLE ......................... 8I-2
RESISTANCE TEST - DIAGNOSIS AND TESTING, FEED CIRCUIT ...............8F-35
RESISTOR BLOCK - DESCRIPTION, BLOWER MOTOR ............... 24-24,24-37
RESISTOR BLOCK - OPERATION, BLOWER MOTOR ............... 24-24,24-37
RESISTOR BLOCK, DIAGNOSIS AND TESTING - FRONT BLOWER MOTOR ......24-25
RESISTOR BLOCK, DIAGNOSIS AND TESTING - REAR BLOWER MOTOR ......24-38
RESONATOR - INSTALLATION ............11-9
RESONATOR - REMOVAL ...............11-9
RESTRAINT ANCHOR - DESCRIPTION, CHILD .............................. 8O-9
RESTRAINT ANCHOR - OPERATION, CHILD ............................. 8O-10
RESTRAINT CONTROLLER - DESCRIPTION, OCCUPANT .............8O-27
RESTRAINT CONTROLLER - INSTALLATION, OCCUPANT ............8O-29
RESTRAINT CONTROLLER - OPERATION, OCCUPANT ......................... 8O-28
RESTRAINT CONTROLLER - REMOVAL, OCCUPANT ......................... 8O-29
RESTRAINTS - DESCRIPTION ............8O-2
RESTRAINTS - OPERATION .............8O-4
RESTRICTION CHECK - DIAGNOSIS AND TESTING, EXHAUST SYSTEM ............11-2
RETAINER - INSTALLATION, CRANKSHAFT REAR OIL SEAL ..........9-132
RETAINER - INSTALLATION, PLASTIC GROCERY BAG ..................... 23-149
RETAINER - REMOVAL, CRANKSHAFT REAR OIL SEAL ...................... 9-132RETAINER - REMOVAL, PLASTIC
GROCERY BAG ..................... 23-149
RETRACTOR - FIRST ROW - OUTBOARD - INSTALLATION, SEAT BELT ...........8O-40
RETRACTOR - FIRST ROW - OUTBOARD - REMOVAL, SEAT BELT ...............8O-39
RETRACTOR - OUTBOARD - FRONT - INSTALLATION, SEAT BELT .............8O-39
RETRACTOR - OUTBOARD - FRONT - REMOVAL, SEAT BELT ................8O-38
RETRACTOR - SECOND ROW - LEFT OUTBOARD - INSTALLATION, SEAT
BELT .............................. 8O-42
RETRACTOR - SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT BELT .....8O-42
RETRACTOR - SECOND ROW - RIGHT OUTBOARD - INSTALLATION, SEAT
BELT .............................. 8O-40
RETRACTOR - SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT BELT .....8O-40
RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT .............8O-41
RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT ................8O-41
RETURN - PCM INPUT - OPERATION, SENSOR ............................ 8E-14
RETURN HOSE - INSTALLATION, HEATER . 24-89
RETURN HOSE - REMOVAL, HEATER .....24-88
RING AND COVER - FOLD-IN-FLOOR - INSTALLATION, CARPET TRIM ..........23-84
RING AND COVER - FOLD-IN-FLOOR - REMOVAL, CARPET TRIM ..............23-84
RING, FITTING - PISTON ................9-47
RING FITTING - STANDARD PROCEDURE, PISTON .................9-124
RINGS - INSTALLATION, PISTON ........9-124
RINGS - REMOVAL, PISTON ............9-124
RISER - 50/50 SPLIT - INSTALLATION, BENCH SEAT ....................... 23-145
RISER - 50/50 SPLIT - REMOVAL, BENCH SEAT ....................... 23-145
RISER - INSTALLATION, LUGGAGE RACK . . 23-58
RISER - INSTALLATION, QUAD BUCKET SEAT ............................. 23-143
RISER - MANUAL - OCS - INSTALLATION, FRONT SEAT ..........23-123
RISER - MANUAL - OCS - REMOVAL, FRONT SEAT ....................... 23-123
RISER - REMOVAL, LUGGAGE RACK .....23-57
RISER - REMOVAL, QUAD BUCKET SEAT . 23-143
RISER - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BASE ..........23-135
RISER - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BASE ..............23-134
RISER - SECOND ROW - INSTALLATION, BENCH SEAT ....................... 23-145
RISER - SECOND ROW - REMOVAL, BENCH SEAT ....................... 23-145
RISER - THIRD ROW - INSTALLATION, BENCH SEAT ....................... 23-145
RISER - THIRD ROW - REMOVAL, BENCH SEAT ....................... 23-145
RISER LATCH LOCKING LINK - INSTALLATION, SEAT .................23-151
RISER LATCH LOCKING LINK - REMOVAL, SEAT .................... 23-151
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - DIAGNOSIS AND TESTING . 21-150, 21-5
ROCKER ARMS - DESCRIPTION .........9-112
ROCKER ARMS - INSPECTION ...........9-35
ROCKER ARMS - INSTALLATION .........9-35
ROCKER ARMS - OPERATION ...........9-112
ROCKER ARMS - REMOVAL .............9-35
ROCKER ARMS AND SHAFT - ASSEMBLY . 9-113
ROCKER ARMS AND SHAFT - DISASSEMBLY ....................... 9-113
ROCKER ARMS AND SHAFT - INSTALLATION ....................... 9-113
ROCKER ARMS AND SHAFT - REMOVAL . . 9-112
ROD - DESCRIPTION, LIFT GEAR & LINK . 8N-16
ROD - DESCRIPTION, PISTON & CONNECTING .................... 9-119,9-44
ROD - INSTALLATION, LIFT GEAR & LINK .............................. 8N-17
ROD - INSTALLATION, OUTER TIE .......19-35 ROD - INSTALLATION, PISTON &
CONNECTING ......................... 9-45
ROD - OPERATION, LIFT GEAR & LINK . . . 8N-16
ROD - REMOVAL, LIFT GEAR & LINK .....8N-16
ROD - REMOVAL, OUTER TIE ...........19-34
ROD - REMOVAL, PISTON & CONNECTING ......................... 9-44
ROD - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ...........23-140
ROD - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT PROP ...............23-139
ROD BEARING CLEARANCE - STANDARD PROCEDURE, MEASURING
CONNECTING ........................ 9-123
ROD, FITTING - CONNECTING ............9-46
RODS - STANDARD PROCEDURE, FITTING CONNECTING .................9-119
ROOF JOINT MOLDING - INSTALLATION . . 23-60
ROOF JOINT MOLDING - REMOVAL ......23-60
ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION,
ARMREST ......................... 23-130
ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR - REMOVAL,
ARMREST ......................... 23-130
ROTATION - STANDARD PROCEDURE, TIRE AND WHEEL ..................... 22-7
ROTOR - DIAGNOSIS AND TESTING, BRAKE .............................. 5-55
ROTOR - INSTALLATION, FRONT BRAKE . . . 5-59
ROTOR - REMOVAL, FRONT BRAKE .......5-59
ROTOR, EXPORT - BRAKE ................5-60
ROTOR MACHINING - STANDARD PROCEDURE, BRAKE ................... 5-58
ROTOR, SPECIFICATIONS - BRAKE ........5-60
RUNOUT, SPECIFICATIONS - TONE WHEEL ............................. 5-91
SAFETY PRECAUTIONS AND WARNINGS, WARNING ........................... 23-1
SAFETY PRECAUTIONS, WARNING - WINDSHIELD ....................... 23-161
SANDING/BUFFING & POLISHING - DESCRIPTION, FINESSE ..............23-101
SBEC CONTROLLER - INSTALLATION .....8E-17
SBEC CONTROLLER - REMOVAL .........8E-16
SCHEMATICS AND DIAGRAMS - 4XTE TRANSAXLE HYDRAULIC SCHEMATICS . . 21-199, 21-54
SCHEMATICS AND DIAGRAMS - SPECIAL TOOLS ............................. 21-68
SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE TRANSAXLE
HYDRAULIC ................... 21-199,21-54
SCREEN - DESCRIPTION, VIDEO ........8A-20
SCREEN - INSTALLATION, VIDEO ........8A-20
SCREEN - OPERATION, VIDEO ..........8A-20
SCREEN - REMOVAL, VIDEO ............8A-20
SCUFF PAD - INSTALLATION, REAR FASCIA .............................. 13-5
SCUFF PAD - REMOVAL, REAR FASCIA ....13-5
SEAL - ASSEMBLY, CALIPER PISTON . . 5-26,5-30
SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP TO FILLER NECK .........7-28
SEAL - DISASSEMBLY, CALIPER PISTON . . . 5-24,
5-28
SEAL - FRONT - INSTALLATION, CRANKSHAFT OIL ................ 9-130,9-42
SEAL - FRONT - REMOVAL, CRANKSHAFT OIL ................ 9-130,9-41
SEAL - OIL PUMP - INSTALLATION .....21-113,
21-264
SEAL - OIL PUMP - REMOVAL . . . 21-113,21-264
SEAL - REAR - INSTALLATION, CRANKSHAFT OIL ................ 9-131,9-42
SEAL - REAR - REMOVAL, CRANKSHAFT OIL ........................... 9-131,9-42
SEAL RETAINER - INSTALLATION, CRANKSHAFT REAR OIL ...............9-132
SEAL RETAINER - REMOVAL, CRANKSHAFT REAR OIL ...............9-132
SEALERS, STANDARD PROCEDURE - FORM-IN-PLACE GASKETS ..........9-11,9-86
SEALING LOCATIONS - FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY ........23-209
SEALING LOCATIONS - SPECIFICATIONS, BODY ............................. 23-183
SEALS - DESCRIPTION, VALVE STEM .....9-114
26 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

STORAGE BIN GUIDE - INSTALLATION,UNDER SEAT ....................... 23-150
STORAGE BIN GUIDE - REMOVAL, UNDER SEAT ....................... 23-150
STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER SEAT ..........23-150
STORAGE BIN LOCK/LATCH - REMOVAL, UNDER SEAT ....................... 23-150
STRAP - INSTALLATION, CHECK .........23-15
STRAP - INSTALLATION, FRONT SEAT BACK ASSIST ...................... 23-112
STRAP - REMOVAL, CHECK ............23-15
STRAP - REMOVAL, FRONT SEAT BACK ASSIST ........................... 23-112
STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW .....23-158
STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW .........23-158
STRIKER - INSTALLATION, CENTER ......23-28
STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER LATCH ...............23-53
STRIKER - INSTALLATION, GLOVE BOX LATCH ............................. 23-66
STRIKER - INSTALLATION, HOLD OPEN LATCH ............................. 23-26
STRIKER - INSTALLATION, LATCH . . 23-19,23-42, 23-64
STRIKER - INSTALLATION, REAR LATCH . . 23-29
STRIKER - REMOVAL, CENTER ..........23-28
STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER LATCH ..................... 23-53
STRIKER - REMOVAL, GLOVE BOX LATCH ............................. 23-66
STRIKER - REMOVAL, HOLD OPEN LATCH ............................. 23-26
STRIKER - REMOVAL, LATCH . 23-19,23-41,23-64
STRIKER - REMOVAL, REAR LATCH ......23-29
STRIPPED THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD ..............9-147
STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-FLOOR ONLY -
SPECIFICATIONS .................... 23-228
STRUCTURAL ADHESIVE LOCATIONS - SPECIFICATIONS .................... 23-218
STRUCTURAL COLLAR - INSTALLATION ....9-49
STRUCTURAL COLLAR - REMOVAL .......9-49
STRUT - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT GAS .....23-139
STRUT - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT GAS .........23-138
STRUT ASSEMBLY - ASSEMBLY ..........2-23
STRUT ASSEMBLY - DESCRIPTION .......2-19
STRUT ASSEMBLY - DIAGNOSIS AND TESTING ............................ 2-20
STRUT ASSEMBLY - DISASSEMBLY .......2-21
STRUT ASSEMBLY - INSTALLATION .......2-25
STRUT ASSEMBLY - OPERATION .........2-19
STRUT ASSEMBLY - REMOVAL ...........2-20
STUDS - FRONT - INSTALLATION, WHEEL MOUNTING ................... 22-21
STUDS - FRONT - REMOVAL, WHEEL MOUNTING ......................... 22-21
STUDS - REAR - INSTALLATION, WHEEL MOUNTING ......................... 22-22
STUDS - REAR - REMOVAL, WHEEL MOUNTING ......................... 22-22
SUCTION LINE - INSTALLATION . . . 24-107,24-97
SUCTION LINE - REMOVAL .......24-106,24-96
SUN VISOR - INSTALLATION ...........23-99
SUN VISOR - REMOVAL ...............23-99
SUN VISOR SUPPORT - INSTALLATION . . . 23-99
SUN VISOR SUPPORT - REMOVAL .......23-99
SUNROOF - DESCRIPTION ............23-169
SUNROOF ASSEMBLY - INSTALLATION . . 23-173
SUNROOF ASSEMBLY - REMOVAL ......23-173
SUNROOF DIAGNOSIS AND TESTING, DIAGNOSIS AND TESTING ............23-169
SUNROOF GLASS PANEL ADJUSTMENT, ADJUSTMENTS ..................... 23-173
SUNROOF MOTOR - INSTALLATION .....23-174
SUNROOF MOTOR - REMOVAL .........23-174
SUNROOF SWITCH - INSTALLATION .....23-176
SUNROOF SWITCH - REMOVAL ........23-176
SUNSHADE - INSTALLATION ...........23-173
SUNSHADE - REMOVAL ..............23-173
SUPPLEMENTAL CABIN HEATER, DIAGNOSIS AND TESTING ............24-114SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT .............................. 8E-15
SUPPORT - INSTALLATION, LUMBAR ....23-150
SUPPORT - INSTALLATION, SUN VISOR . . . 23-99
SUPPORT - REMOVAL, LUMBAR .......23-150
SUPPORT - REMOVAL, SUN VISOR ......23-99
SUPPORT CYLINDER - INSTALLATION ....23-43
SUPPORT CYLINDER - REMOVAL ........23-42
SUPPORT PLATE - DRUM BRAKE - INSTALLATION ........................ 5-61
SUPPORT PLATE - DRUM BRAKE - REMOVAL ........................... 5-61
SUPPRESSION COMPONENTS - DESCRIPTION, RADIO NOISE ...........8A-15
SUPPRESSION COMPONENTS - OPERATION, RADIO NOISE .............8A-15
SURFACE PREPARATION - STANDARD PROCEDURE, ENGINE GASKET .......9-11,9-87
SUSPENSION - DESCRIPTION, FRONT ......2-2
SUSPENSION - DESCRIPTION, REAR ......2-26
SUSPENSION - OPERATION, FRONT ........2-2
SUSPENSION AND STEERING - DIAGNOSIS AND TESTING ..............2-50
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - FRONT ................2-3
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - REAR ................2-28
SUSPENSION, SPECIAL TOOLS - FRONT ....2-3
SUSPENSION, SPECIAL TOOLS - REAR ....2-28
SWITCH - DESCRIPTION .................8P-5
SWITCH - DESCRIPTION, B-PILLAR ......8N-52
SWITCH - DESCRIPTION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - DESCRIPTION, BRAKE LAMP ....8L-4
SWITCH - DESCRIPTION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - DESCRIPTION, FULL OPEN ....8N-11,
8N-52
SWITCH - DESCRIPTION, HEATED SEAT . . . 8G-8
SWITCH - DESCRIPTION, HORN ..........8H-4
SWITCH - DESCRIPTION, MEMORY ......8N-36
SWITCH - DESCRIPTION, OIL PRESSURE . 9-144
SWITCH - DESCRIPTION, REAR WINDOW DEFOGGER .................. 8G-4
SWITCH - DESCRIPTION, REAR WIPER/WASHER ..................... 8R-10
SWITCH - DESCRIPTION, SEAT .........8N-34
SWITCH - DIAGNOSIS AND TESTING, BRAKE LAMP ........................ 8L-4
SWITCH - DIAGNOSIS AND TESTING, FAILED PARK ........................ 8R-2
SWITCH - DIAGNOSIS AND TESTING, FRONT WIPER/WASHER ................8R-2
SWITCH - DIAGNOSIS AND TESTING, HEADLAMP ......................... 8L-13
SWITCH - DIAGNOSIS AND TESTING, MULTI-FUNCTION .................... 8L-18
SWITCH - DIAGNOSIS AND TESTING, TRACTION CONTROL ................... 5-94
SWITCH - EXPORT - DESCRIPTION, DOOR CYLINDER LOCK ...............8N-22
SWITCH - EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - INSTALLATION, HOOD AJAR ......................... 8Q-3
SWITCH - EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR ...........8N-30
SWITCH - EXPORT - OPERATION, DOOR CYLINDER LOCK ..................... 8N-22
SWITCH - EXPORT - OPERATION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - REMOVAL, HOOD AJAR ............................... 8Q-3
SWITCH - EXPORT - REMOVAL, POWER FOLDAWAY MIRROR .................. 8N-29
SWITCH - INSTALLATION ...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - INSTALLATION, B-PILLAR .....8N-52
SWITCH - INSTALLATION, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-5
SWITCH - INSTALLATION, CENTER CONSOLE LAMP ..................... 8L-21
SWITCH - INSTALLATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - INSTALLATION, FULL OPEN ....8N-11 SWITCH - INSTALLATION, GLOVE BOX
LAMP .............................. 8L-22
SWITCH - INSTALLATION, HEADLAMP ....8L-13
SWITCH - INSTALLATION, IGNITION ......19-19
SWITCH - INSTALLATION, MULTI- FUNCTION .......................... 8L-18
SWITCH - INSTALLATION, OIL PRESSURE ..................... 9-144,9-56
SWITCH - INSTALLATION, SUNROOF ....23-176
SWITCH - INSTALLATION, TRACTION CONTROL ........................... 5-95
SWITCH - INSTALLATION, WASHER FLUID LEVEL ........................ 8R-11
SWITCH - OPERATION .................8P-5
SWITCH - OPERATION, B-PILLAR ........8N-52
SWITCH - OPERATION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - OPERATION, BRAKE LAMP ......8L-4
SWITCH - OPERATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - OPERATION, FULL OPEN . 8N-11,8N-52
SWITCH - OPERATION, HEATED SEAT .....8G-9
SWITCH - OPERATION, MEMORY ........8N-36
SWITCH - OPERATION, OIL PRESSURE . . . 9-144
SWITCH - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-4
SWITCH - OPERATION, REAR WIPER/ WASHER ........................... 8R-11
SWITCH - OPERATION, SEAT ...........8N-34
SWITCH - REMOVAL .................... 8P-5
SWITCH - REMOVAL, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - REMOVAL, B-PILLAR .........8N-52
SWITCH - REMOVAL, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - REMOVAL, BRAKE LAMP .......8L-5
SWITCH - REMOVAL, CENTER CONSOLE LAMP .............................. 8L-21
SWITCH - REMOVAL, EXTERIOR HANDLE . 8N-10
SWITCH - REMOVAL, FULL OPEN .......8N-11
SWITCH - REMOVAL, GLOVE BOX LAMP . . 8L-22
SWITCH - REMOVAL, HEADLAMP ........8L-13
SWITCH - REMOVAL, IGNITION .........19-17
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE ....9-144,
9-56
SWITCH - REMOVAL, SUNROOF ........23-176
SWITCH - REMOVAL, TRACTION CONTROL ........................... 5-95
SWITCH - REMOVAL, WASHER FLUID LEVEL ............................. 8R-11
SWITCH ASSY - DESCRIPTION, SOLENOID/PRESSURE ..........21-117,21-268
SWITCH ASSY - INSTALLATION, SOLENOID/PRESSURE ..........21-119,21-270
SWITCH ASSY - OPERATION, SOLENOID/ PRESSURE .................. 21-118,21-268
SWITCH ASSY - REMOVAL, SOLENOID/ PRESSURE .................. 21-118,21-269
SWITCH, DIAGNOSIS AND TESTING - DOOR LOCK ........................ 8N-23
SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED SEAT .................8G-9
SWITCH, DIAGNOSIS AND TESTING - DRIVER SEAT ....................... 8N-34
SWITCH, DIAGNOSIS AND TESTING - MEMORY ........................... 8N-37
SWITCH, DIAGNOSIS AND TESTING - REMOTE ........................... 8N-30
SWITCH, DIAGNOSIS AND TESTING - WINDOW ........................... 8N-63
SWITCH, EXPORT - DOOR CYLINDER LOCK .............................. 8N-22
SWITCHES - DESCRIPTION, REMOTE .....8A-16
SWITCHES - OPERATION, REMOTE ......8A-16
SWITCHES, DIAGNOSIS AND TESTING - REMOTE ........................... 8A-16
SYMBOLS - DESCRIPTION, INTERNATIONAL .......................0-1
SYNCHRONIZING CABLE ADJUSTMENT, INSTALLATION ................ 23-105,23-147
TAIL LAMP - INSTALLATION ............8L-19
TAIL LAMP - REMOVAL ................8L-18
TAIL LAMP UNIT - INSTALLATION .......8L-19
TAIL LAMP UNIT - REMOVAL ...........8L-19
TANK - DESCRIPTION, FUEL ............14-12
TANK - OPERATION, FUEL ..............14-12
RS INDEX31
Description Group-Page Description Group-Page Description Group-Page

TO CYLINDER BORE FITTING -STANDARD PROCEDURE, PISTON ........9-44
TO FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP ...........7-28
TO GROUND - STANDARD PROCEDURE, TESTING FOR A SHORT .............8W-01-9
TO GROUND ON FUSES POWERING SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS - DESCRIPTION, HOW ................8W -01-1
TONE WHEEL - INSPECTION .............5-94
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-91
TOOLS - 2.4L ENGINE, SPECIAL ..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL .......9-98
TOOLS - 41TE AUTOMATIC TRANSAXLE, SPECIAL .......................... 21-213
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10
TOOLS - BATTERY SYSTEM SPECIAL TOOLS, SPECIAL ...................... 8F-7
TOOLS - BODY, SPECIAL ...............23-13
TOOLS - COOLING SYSTEM, SPECIAL ......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL .....11-4
TOOLS - FRONT SUSPENSION, SPECIAL ....2-3
TOOLS - FUEL, SPECIAL ...........14-27,14-4
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-7
TOOLS - POWER DISTRIBUTION SYSTEMS, SPECIAL ................8W -97-1
TOOLS - POWER STEERING GEAR, SPECIAL ........................... 19-34
TOOLS - POWER STEERING PUMP, SPECIAL ........................... 19-44
TOOLS - POWER STEERING, SPECIAL .....19-9
TOOLS - REAR SUSPENSION, SPECIAL ....2-28
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, SCHEMATICS AND DIAGRAMS - SPECIAL ........................... 21-68
TOOLS, SPECIAL TOOLS - BATTERY SYSTEM SPECIAL ..................... 8F-7
TOOLS, SPECIFICATIONS - SPECIAL ......8F-24
TOP COVER - INSTALLATION, INSTRUMENT PANEL .................. 23-72
TOP COVER - REMOVAL, INSTRUMENT PANEL ............................. 23-72
TOP PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL .................. 23-77
TOP PAD ASSEMBLY - REMOVAL, INSTRUMENT PANEL .................. 23-77
TORQUES, SPECIFICATIONS ............8F-36
TOUCH-UP - DESCRIPTION, PAINTED ....23-101
TOWING - STANDARD PROCEDURE .......0-26
TPM - CAUTION, SENSOR ..............22-11
TPM - DESCRIPTION, SENSOR ..........22-10
TPM - INSTALLATION, SENSOR .........22-11
TPM - OPERATION, SENSOR ............22-10
TPM - REMOVAL, SENSOR .............22-11
TRACK - DESCRIPTION, POWER SEAT ....8N-37
TRACK - INSTALLATION, BENCH SEAT . . . 23-148
TRACK - OPERATION, POWER SEAT .....8N-38
TRACK & RACK - DESCRIPTION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - INSTALLATION, LOWER DRIVE UNIT .................. 8N-58
TRACK & RACK - OPERATION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - REMOVAL, LOWER DRIVE UNIT ........................ 8N-57
TRACK - REAR COVER - INSTALLATION, FRONT SEAT ....................... 23-128
TRACK - REAR COVER - REMOVAL, FRONT SEAT ....................... 23-128
TRACK - REMOVAL, BENCH SEAT .......23-148
TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT SEAT ..........23-128
TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT SEAT ..............23-126
TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT SEAT ..........23-125
TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT SEAT ..............23-124
TRACK BAR - DESCRIPTION .............2-45
TRACK BAR - INSTALLATION ............2-46
TRACK BAR - OPERATION ...............2-46
TRACK BAR - REMOVAL ................2-46
TRACK, DIAGNOSIS AND TESTING - POWER SEAT ....................... 8N-38
TRACK MANUAL ADJUSTER - INSTALLATION, FRONT SEAT ..........23-126TRACK MANUAL ADJUSTER - REMOVAL,
FRONT SEAT ....................... 23-125
TRACK POWER ADJUSTER - INSTALLATION, FRONT SEAT ..........23-124
TRACK POWER ADJUSTER - REMOVAL, FRONT SEAT ....................... 23-124
TRACK REAR COVER - OCS - INSTALLATION, FRONT SEAT ..........23-129
TRACK REAR COVER - OCS - REMOVAL, FRONT SEAT ....................... 23-129
TRACTION CONTROL SWITCH - DIAGNOSIS AND TESTING ..............5-94
TRACTION CONTROL SWITCH - INSTALLATION ........................ 5-95
TRACTION CONTROL SWITCH - REMOVAL ........................... 5-95
TRACTION CONTROL SYSTEM - DESCRIPTION ........................ 5-88
TRACTION CONTROL SYSTEM - OPERATION .......................... 5-89
TRANSAXLE - DESCRIPTION, 40TE AUTOMATIC .......................... 21-2
TRANSAXLE - DESCRIPTION, 41TE AUTOMATIC ........................ 21-147
TRANSAXLE - OPERATION, 40TE AUTOMATIC .......................... 21-4
TRANSAXLE - OPERATION, 41TE AUTOMATIC ........................ 21-149
TRANSAXLE - SPECIFICATIONS, 41TE . . . 21-211, 21-66
TRANSAXLE FLUID - DESCRIPTION, AUTOMATIC/MANUAL ...................0-4
TRANSAXLE GENERAL DIAGNOSIS - DIAGNOSIS AND TESTING, 4XTE .....21-149,21-5
TRANSAXLE HYDRAULIC SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE . . . 21-199, 21-54
TRANSAXLE, SPECIAL TOOLS - 41TE AUTOMATIC ........................ 21-213
TRANSDUCER - DESCRIPTION, A/C PRESSURE ......................... 24-20
TRANSDUCER - OPERATION, A/C PRESSURE ......................... 24-20
TRANSDUCER, DIAGNOSIS AND TESTING - A/C PRESSURE .............24-21
TRANSFER UNIT FLUID - DESCRIPTION, AWD POWER ..........................0-6
TRANSMISSION CONTROL RELAY - DESCRIPTION ................ 21-130,21-281
TRANSMISSION CONTROL RELAY - OPERATION .................. 21-130,21-281
TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/
ASSEMBLY - STANDARD PROCEDURE .....7-38
TRANSMISSION OIL COOLER - DESCRIPTION ........................ 7-39
TRANSMISSION OIL COOLER - INSPECTION ......................... 7-39
TRANSMISSION OIL COOLER LINES - INSTALLATION ........................ 7-40
TRANSMISSION OIL COOLER LINES - REMOVAL ........................... 7-39
TRANSMISSION RANGE SENSOR - DESCRIPTION ................ 21-130,21-281
TRANSMISSION RANGE SENSOR - INSTALLATION ................ 21-131,21-282
TRANSMISSION RANGE SENSOR - OPERATION .................. 21-131,21-282
TRANSMISSION RANGE SENSOR - REMOVAL ................... 21-131,21-282
TRANSMITTER - DESCRIPTION, UNIVERSAL ........................ 8M-11
TRANSMITTER CODES, STANDARD PROCEDURE - ERASING ..............8M-12
TRANSMITTER CODES, STANDARD PROCEDURE - SETTING ...............8M-12
TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS ENTRY ............8N-24
TRANSMITTER, DIAGNOSIS AND TESTING - UNIVERSAL ...............8M-11
TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ENTRY ..................... 8N-24
TRANSMITTER RANGE - SPECIFICATIONS ..................... 8N-24
TRANSPONDER KEY - DESCRIPTION ......8Q-6
TRANSPONDER KEY - OPERATION ........8Q-6TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE ...............8Q-6
TRANSVERSE BRACKET - DESCRIPTION . . 8N-19
TRANSVERSE BRACKET - INSTALLATION . . 8N-19
TRANSVERSE BRACKET - OPERATION ....8N-19
TRANSVERSE BRACKET - REMOVAL .....8N-19
TRAY - DESCRIPTION, BATTERY .........8F-19
TRAY - INSTALLATION, BATTERY ........8F-20
TRAY - INSTALLATION, FLOOR CONSOLE BASE .............................. 23-89
TRAY - REMOVAL, BATTERY ............8F-19
TRAY - REMOVAL, FLOOR CONSOLE BASE .............................. 23-89
TREAD WEAR INDICATORS - DIAGNOSIS AND TESTING ....................... 22-16
TRIM - INSTALLATION, A-PILLAR ........23-79
TRIM - INSTALLATION, A-PILLAR LOWER EXTENSION .................. 23-79
TRIM - INSTALLATION, B-PILLAR LOWER ............................ 23-80
TRIM - INSTALLATION, B-PILLAR UPPER . . 23-80
TRIM - INSTALLATION, COWL ..........23-88
TRIM - INSTALLATION, C-PILLAR ........23-88
TRIM - INSTALLATION, REAR HEADER ....23-96
TRIM - REMOVAL, A-PILLAR ...........23-79
TRIM - REMOVAL, A-PILLAR LOWER EXTENSION ......................... 23-79
TRIM - REMOVAL, B-PILLAR LOWER .....23-79
TRIM - REMOVAL, B-PILLAR UPPER .......23-80
TRIM - REMOVAL, COWL ..............23-88
TRIM - REMOVAL, C-PILLAR ...........23-88
TRIM - REMOVAL, REAR HEADER .......23-96
TRIM BOLSTER - INSTALLATION, QUARTER .......................... 23-95
TRIM BOLSTER - REMOVAL, QUARTER . . . 23-95
TRIM CARE, CLEANING - WHEEL AND WHEEL ............................ 22-19
TRIM PANEL - INSTALLATION .....23-20,23-34,
23-43
TRIM PANEL - INSTALLATION, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - INSTALLATION, LEFT QUARTER .......................... 23-94
TRIM PANEL - INSTALLATION, RIGHT D-PILLAR ........................... 23-98
TRIM PANEL - INSTALLATION, RIGHT QUARTER .......................... 23-97
TRIM PANEL - REMOVAL ....23-20,23-34,23-43
TRIM PANEL - REMOVAL, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - REMOVAL, LEFT QUARTER .......................... 23-94
TRIM PANEL - REMOVAL, RIGHT D-PILLAR ........................... 23-97
TRIM PANEL - REMOVAL, RIGHT QUARTER .......................... 23-97
TRIM PLATE - INSTALLATION, DOOR SILL ............................... 23-89
TRIM PLATE - REMOVAL, DOOR SILL ....23-89
TRIM RING AND COVER - FOLD-IN- FLOOR - INSTALLATION, CARPET ........23-84
TRIM RING AND COVER - FOLD-IN- FLOOR - REMOVAL, CARPET ...........23-84
TRIP DEFINITION, DESCRIPTION .........25-1
TROUBLE CODES - STANDARD PROCEDURE, OBTAINING DIAGNOSTIC . . . 8E-15
TUB CARPET INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR ....23-98
TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR ........23-98
TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR ..........23-96
TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR .............23-95
TUBE - 2.4L - DESCRIPTION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - INSTALLATION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - REMOVAL, WATER PUMP INLET ............................... 7-36
TUBE - 3.3/3.8L - INSTALLATION, WATER PUMP INLET ......................... 7-37
TUBE - 3.3/3.8L - REMOVAL, WATER PUMP INLET ......................... 7-37
TUBE - INSTALLATION, DRAIN .........23-172
TUBE - INSTALLATION, EXHAUST .......24-116
TUBE - INSTALLATION, FUEL TANK FILLER ............................. 14-17
RS INDEX33
Description Group-Page Description Group-Page Description Group-Page