headlamp CHRYSLER CARAVAN 2005 Manual PDF

REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the center bezel from the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL).
(3) Place the instrument panel center bezel unit
face down on a suitable work surface. Take the
proper precautions to protect the center bezel from
cosmetic damage.
(4) If the vehicle is equipped with the optional
Automatic Temperature Control (ATC) system, dis-
connect the infrared sensor jumper harness connector
from the receptacle on the back of the A/C-heater
control (Fig. 9).
(5) Remove the six screws that secure the A/C-
heater control to the back of the instrument panel
center bezel.
(6) Remove the A/C-heater control from the instru-
ment panel center bezel.
INSTALLATION
(1) Position the A/C-heater control onto the back of
instrument panel center bezel.
(2) Install the six screws that secure the A/C-
heater control to the back of the instrument panel
center bezel. Tighten the screws to 2 N´m (17 in.
lbs.).
(3) If the vehicle is equipped with the optional
ATC system, reconnect the infrared sensor jumper
harness connector to A/C-heater control.
(4) Install the center bezel onto the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL - INSTAL-
LATION).
(5) Reconnect the battery negative cable.
A/C PRESSURE TRANSDUCER
DESCRIPTION
The A/C pressure transducer is a switch that is
installed on a fitting located on the refrigerant liquid
line between the receiver/drier and the expansion
valve in the right rear corner of the engine compart-
ment. An internally threaded hex fitting on the
transducer connects it to the externally threaded
Schrader-type fitting on the liquid line. A rubber
O-ring seals the connection between the transducer
and the liquid line fitting. Three terminals within a
molded plastic connector receptacle on the top of the
transducer connect it to the vehicle electrical system
through a wire lead and connector of the headlamp
and dash wire harness.
The A/C pressure transducer cannot be adjusted or
repaired and, if faulty or damaged, it must be
replaced.
OPERATION
The A/C pressure transducer monitors the pres-
sures in the high side of the refrigerant system
through its connection to a fitting on the liquid line.
The transducer will change its internal resistance in
response to the pressures it monitors. The power-
train control module (PCM) provides a five volt ref-
erence signal and a sensor ground to the transducer,
then monitors the output voltage of the transducer
on a sensor return circuit to determine refrigerant
pressure. The PCM is programmed to respond to this
and other sensor inputs by controlling the operation
of the A/C compressor clutch and the radiator cooling
fan to help optimize air conditioning system perfor-
Fig. 9 A/C-Heater Control ± ATC shown, MTC typical
1 - INFRARED SENSOR CONNECTOR (ATC ONLY)
2 - INFRARED SENSOR HARNESS (ATC ONLY)
3 - A/C-HEATER CONTROL
4 - SCREW (6)
5- INSTRUMENT PANEL CENTER BEZEL
24 - 20 CONTROLS - FRONTRS
A/C HEATER CONTROL (Continued)

AJAR SWITCH - EXPORT -INSTALLATION, HOOD .................8Q-3
AJAR SWITCH - EXPORT - REMOVAL, HOOD .............................. 8Q-3
ALIGNMENT - DESCRIPTION, WHEEL ......2-47
ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT .....8L-9
ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT .........8L-15
ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ................8L-9
ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ARM ................... 8R-9
ALIGNMENT - STANDARD PROCEDURE, HEADLAMP UNIT ..................... 8L-14
ALIGNMENT - STANDARD PROCEDURE, WHEEL ............................. 2-52
ALIGNMENT, SPECIFICATIONS - WHEEL ....2-56
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-12
AMBIENT TEMP SENSOR - OPERATION . . 8M-12
AMBIENT TEMPERATURE SENSOR CIRCUIT, DIAGNOSIS AND TESTING .....8M-12
AMBIENT TEMPERATURE SENSOR, DIAGNOSIS AND TESTING .............8M-12
AMPLIFIER - INSTALLATION .............8A-7
AMPLIFIER - REMOVAL ................8A-7
AN AIRBAG DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER ...........8O-7
ANCHOR - DESCRIPTION, CHILD RESTRAINT .......................... 8O-9
ANCHOR - OPERATION, CHILD RESTRAINT .......................... 8O-10
ANTENNA - EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - EXPORT - OPERATION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - NAVIGATION RADIO - INSTALLATION ....................... 8A-11
ANTENNA - NAVIGATION RADIO - REMOVAL .......................... 8A-11
ANTENNA BODY AND CABLE - DESCRIPTION ........................ 8A-7
ANTENNA BODY AND CABLE - OPERATION .......................... 8A-7
ANTENNA BODY AND CABLE, DIAGNOSIS AND TESTING ..............8A-8
ANTENNA CABLE - INSTALLATION, INSTRUMENT PANEL .................8A-12
ANTENNA CABLE - REMOVAL, INSTRUMENT PANEL .................8A-12
ANTENNA, EXPORT - QUARTER GLASS INTEGRAL .......................... 8A-13
ANTENNA MODULE - EXPORT - DESCRIPTION ....................... 8A-10
ANTENNA MODULE - EXPORT - OPERATION ......................... 8A-10
ANTENNA MODULE, EXPORT ...........8A-10
ANTILOCK BRAKE - DESCRIPTION, CONTROLLER ........................ 8E-4
ANTILOCK BRAKE - INSTALLATION, CONTROLLER ........................ 8E-6
ANTILOCK BRAKE - OPERATION, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE - REMOVAL, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE SYSTEM - DESCRIPTION ........................ 5-87
ANTILOCK BRAKE SYSTEM - OPERATION . . 5-88
ANTILOCK BRAKE SYSTEM BLEEDING - STANDARD PROCEDURE ................5-90
ANTILOCK BRAKE SYSTEM (EXPORT) - DESCRIPTION ........................ 5-87
A-PILLAR LOWER EXTENSION TRIM - INSTALLATION ....................... 23-79
A-PILLAR LOWER EXTENSION TRIM - REMOVAL .......................... 23-79
A-PILLAR TRIM - INSTALLATION ........23-79
A-PILLAR TRIM - REMOVAL ............23-79
A-PILLAR-HEADER, OR B-PILLAR - INSTALLATION ....................... 23-17
A-PILLAR-HEADER, OR B-PILLAR - REMOVAL .......................... 23-17
APPLIQUE - INSTALLATION .............23-14
APPLIQUE - REMOVAL ................23-14
ARM - DESCRIPTION, LOWER CONTROL . . . 2-12
ARM - INSPECTION, LOWER CONTROL ....2-14
ARM - INSTALLATION, LOWER CONTROL . . 2-15
ARM - INSTALLATION, REAR WIPER .....8R-10 ARM - OPERATION, LOWER CONTROL
.....2-12
ARM - REMOVAL, LOWER CONTROL ......2-12
ARM - REMOVAL, REAR WIPER .........8R-10
ARM ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ............8R-9
ARM (REAR BUSHING - HYDRO) - ASSEMBLY, LOWER CONTROL ...........2-15
ARM (REAR BUSHING - HYDRO) - DISASSEMBLY, LOWER CONTROL ........2-13
ARM (REAR BUSHING - STANDARD) - ASSEMBLY, LOWER CONTROL ...........2-14
ARM (REAR BUSHING - STANDARD) - DISASSEMBLY, LOWER CONTROL ........2-13
ARMREST - INSTALLATION ............23-108
ARMREST - REMOVAL ...............23-108
ARMREST - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION ..............23-130
ARMREST - SECOND ROW - FOLD-IN- FLOOR - REMOVAL .................. 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION ...................... 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
REMOVAL ......................... 23-130
ARMS - DESCRIPTION, ROCKER ........9-112
ARMS - INSPECTION, ROCKER ...........9-35
ARMS - INSTALLATION, FRONT WIPER ....8R-9
ARMS - INSTALLATION, ROCKER .........9-35
ARMS - OPERATION, ROCKER ..........9-112
ARMS - REMOVAL, FRONT WIPER .........8R-9
ARMS - REMOVAL, ROCKER .............9-35
ARMS AND SHAFT - ASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - DISASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - INSTALLATION, ROCKER ............................ 9-113
ARMS AND SHAFT - REMOVAL, ROCKER . . 9-112
ASSIST DISPLAY - DESCRIPTION, PARK . . . 8B-3
ASSIST DISPLAY - INSTALLATION, PARK . . . 8B-4
ASSIST DISPLAY - OPERATION, PARK .....8B-3
ASSIST DISPLAY - REMOVAL, PARK ......8B-4
ASSIST HANDLE - INSTALLATION ........23-79
ASSIST HANDLE - REMOVAL ...........23-79
ASSIST MODULE - DESCRIPTION, PARK . . . 8B-4
ASSIST MODULE - INSTALLATION, PARK . . 8B-6
ASSIST MODULE - OPERATION, PARK .....8B-5
ASSIST MODULE - REMOVAL, PARK ......8B-5
ASSIST SENSOR - DESCRIPTION, PARK . . . 8B-6
ASSIST SENSOR - INSTALLATION, PARK . . . 8B-6
ASSIST SENSOR - OPERATION, PARK .....8B-6
ASSIST SENSOR - REMOVAL, PARK ......8B-6
ASSIST STRAP - INSTALLATION, FRONT SEAT BACK ........................ 23-112
ASSIST STRAP - REMOVAL, FRONT SEAT BACK ........................ 23-112
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - ADHESIVE .............23-51
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - TAPE .................23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - ADHESIVE .................. 23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - TAPE ...................... 23-51
AUDIO/VIDEO - DESCRIPTION ...........8A-1
AUDIO/VIDEO, DIAGNOSIS AND TESTING . . 8A-2
AUTO SHUT DOWN RELAY - DESCRIPTION ......................... 8I-3
AUTO SHUT DOWN RELAY - OPERATION . . . 8I-3
AUTOMATIC ADJUSTER - DIAGNOSIS AND TESTING, DRUM BRAKE ............5-14
AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD PROCEDURE,
PARKING BRAKE ...................... 5-63
AUTOMATIC ADJUSTER TENSION RESET - STANDARD PROCEDURE, PARKING
BRAKE .............................. 5-64
AUTOMATIC DAY / NIGHT MIRROR - DESCRIPTION ....................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR - OPERATION ......................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR, DIAGNOSIS AND TESTING .............8N-28
AUTOMATIC TEMPERATURE CONTROL, DESCRIPTION ........................ 24-3
AUTOMATIC TEMPERATURE CONTROL, OPERATION .......................... 24-5AUTOMATIC TEMPERATURE CONTROL
SYSTEM, OPERATION ................24-114
AUTOMATIC TRANSAXLE - DESCRIPTION, 40TE ................... 21-2
AUTOMATIC TRANSAXLE - DESCRIPTION, 41TE .................21-147
AUTOMATIC TRANSAXLE - OPERATION, 40TE ............................... 21-4
AUTOMATIC TRANSAXLE - OPERATION, 41TE ............................. 21-149
AUTOMATIC TRANSAXLE, SPECIAL TOOLS - 41TE ...................... 21-213
AUTOMATIC/MANUAL TRANSAXLE FLUID - DESCRIPTION ........................0-4
AWD - INSTALLATION ..................2-45
AWD - INSTALLATION, REAR WHEEL SPEED SENSOR ....................... 5-92
AWD - INSTALLATION, SPRING ..........2-39
AWD - REMOVAL ..................... 2-44
AWD - REMOVAL, REAR WHEEL SPEED SENSOR ............................ 5-92
AWD - REMOVAL, SPRING ..............2-38
AWD, HEAVY DUTY, CARGO - INSTALLATION ........................ 2-36
AWD, HEAVY DUTY, CARGO - REMOVAL . . . 2-36
AWD POWER TRANSFER UNIT FLUID - DESCRIPTION .........................0-6
AWD REAR DRIVELINE MODULE FLUIDS - DESCRIPTION ........................0-6
B OR C-PILLAR - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ..............8O-38
B OR C-PILLAR - REMOVAL, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
BACK - INSTALLATION, BENCH SEAT ....23-147
BACK - INSTALLATION, FRONT SEAT ....23-111
BACK - QUAD BUCKET - INSTALLATION, BUCKET SEAT ...................... 23-141
BACK - QUAD BUCKET - REMOVAL, BUCKET SEAT ...................... 23-140
BACK - REMOVAL, BENCH SEAT ........23-147
BACK - REMOVAL, FRONT SEAT ........23-111
BACK ASSIST STRAP - INSTALLATION, FRONT SEAT ....................... 23-112
BACK ASSIST STRAP - REMOVAL, FRONT SEAT ....................... 23-112
BACK COVER - INSTALLATION, BENCH SEAT ............................. 23-148
BACK COVER - INSTALLATION, FRONT SEAT ............................. 23-116
BACK COVER - REMOVAL, BENCH SEAT . . 23-148
BACK COVER - REMOVAL, FRONT SEAT . . 23-113
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-133
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-133
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-156
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-155
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-134
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-134
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-157
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-156
BACK HINGE - REMOVAL, BENCH SEAT . . 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION,
SEAT ............................. 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT . . 23-146
BACK PANEL - INSTALLATION, BENCH SEAT ............................. 23-144
BACK PANEL - INSTALLATION, FRONT SEAT ............................. 23-113
BACK PANEL - REMOVAL, BENCH SEAT . . 23-143
BACK PANEL - REMOVAL, FRONT SEAT . . 23-112
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT ............................. 23-134
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT .....23-134
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-158
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - REMOVAL, SEAT .............23-158
2 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

ENGINE OIL PRESSURE - DIAGNOSISAND TESTING, CHECKING ...............9-53
ENGINE, SPECIAL TOOLS - 2.4L ..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L .......9-98
ENGINE, SPECIFICATIONS - 3.3/3.8L ......9-93
ENGINE SPEED SENSOR - DESCRIPTION . . 14-30
ENGINE SPEED SENSOR - OPERATION ....14-30
ENGINE, STANDARD PROCEDURE - HYDROSTATIC LOCKED .............9-10,9-87
ENGINES - DESCRIPTION, ENGINE OIL - DIESEL ..............................0-6
ENGINES - EXPORT - DESCRIPTION, DIESEL ............................. 0-21
ENGINES, INSTALLATION - 2.4L/3.3L/ 3.8L ............................... 24-77
ENGINES, INSTALLATION - 2.5L/2.8L DIESEL ............................ 24-78
ENGINES, REMOVAL - 2.4L/3.3L/3.8L .....24-76
ENGINES, REMOVAL - 2.5L/2.8L DIESEL . . 24-77
ENTRY MODULE - DESCRIPTION, SENTRY KEY REMOTE .................8Q-3
ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-5
ENTRY MODULE - INSTALLATION, SENTRY KEY REMOTE .................8Q-6
ENTRY MODULE - OPERATION, SENTRY KEY REMOTE ........................ 8Q-4
ENTRY MODULE - REMOVAL, SENTRY KEY REMOTE ........................ 8Q-6
ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-3
ENTRY TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS .................. 8N-24
ENTRY TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ........................... 8N-24
EQUIPMENT, STANDARD PROCEDURE - REFRIGERANT SYSTEM SERVICE ........24-69
ERASING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
EVACUATE, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-70
EVAP CANISTER - INSTALLATION, REAR . . 25-21
EVAP CANISTER - REMOVAL, REAR ......25-20
EVAPORATION CONTROL SYSTEM - OPERATION ......................... 25-11
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-98
EVAPORATOR - INSTALLATION, A/C ......24-81
EVAPORATOR - OPERATION, A/C . . . 24-80,24-98
EVAPORATOR - REMOVAL, A/C ..........24-81
EVAPORATOR, INSTALLATION - REAR A/C............................... 24-100
EVAPORATOR LINE EXTENSION, INSTALLATION - REAR A/C ............24-100
EVAPORATOR LINE EXTENSION, REMOVAL - REAR A/C .................24-99
EVAPORATOR, REMOVAL - REAR A/C .....24-98
EVAPORATOR TEMPERATURE SENSOR - DESCRIPTION ....................... 24-26
EVAPORATOR TEMPERATURE SENSOR - OPERATION ......................... 24-27
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-13
EVAP/PURGE SOLENOID - INSTALLATION . 25-13
EVAP/PURGE SOLENOID - OPERATION ....25-13
EVAP/PURGE SOLENOID - REMOVAL .....25-13
EXCESSIVE EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING ..............11-2
EXHAUST MANIFOLD - CLEANING ........9-63
EXHAUST MANIFOLD - INSPECTION .......9-63
EXHAUST MANIFOLD - INSTALLATION .....9-63
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-154
EXHAUST MANIFOLD - LEFT - INSPECTION ........................ 9-155
EXHAUST MANIFOLD - LEFT - INSTALLATION ....................... 9-155
EXHAUST MANIFOLD - LEFT - REMOVAL . . 9-154
EXHAUST MANIFOLD - REMOVAL .........9-63
EXHAUST MANIFOLD - RIGHT - CLEANING .......................... 9-153
EXHAUST MANIFOLD - RIGHT - INSPECTION ........................ 9-153
EXHAUST MANIFOLD - RIGHT - INSTALLATION ....................... 9-153
EXHAUST MANIFOLD - RIGHT - REMOVAL .......................... 9-152
EXHAUST SYSTEM - DESCRIPTION .......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING, EXCESSIVE ..............11-2EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING .............11-2
EXHAUST SYSTEM, SPECIAL TOOLS ......11-4
EXHAUST TUBE - INSTALLATION .......24-116
EXHAUST TUBE - REMOVAL ...........24-116
EXHAUSTER - DESCRIPTION, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXHAUSTER - INSTALLATION, REAR QUARTER PANEL/FENDER AIR ..........23-60
EXHAUSTER - REMOVAL, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXPANSION VALVE - DESCRIPTION ......24-81
EXPANSION VALVE - DESCRIPTION, A/C . 24-100
EXPANSION VALVE - OPERATION ........24-81
EXPANSION VALVE - OPERATION, A/C . . . 24-100
EXPANSION VALVE, DIAGNOSIS AND TESTING - FRONT A/C .................24-82
EXPANSION VALVE, DIAGNOSIS AND TESTING - REAR A/C .................24-101
EXPORT - ANTENNA MODULE ..........8A-10
EXPORT - BRAKE ROTOR ...............5-60
EXPORT - DESCRIPTION ................5-63
EXPORT - DESCRIPTION ................0-13
EXPORT - DESCRIPTION ................2-10
EXPORT - DESCRIPTION, ANTENNA MODULE ........................... 8A-10
EXPORT - DESCRIPTION, DIESEL ENGINES ............................ 0-21
EXPORT - DESCRIPTION, DOOR CYLINDER LOCK SWITCH ...............8N-22
EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ANTENNA ............8A-13
EXPORT - DOOR CYLINDER LOCK SWITCH ............................ 8N-22
EXPORT - INSTALLATION ...............5-68
EXPORT - INSTALLATION ...............2-11
EXPORT - INSTALLATION, HEADLAMP UNIT .............................. 8L-17
EXPORT - INSTALLATION, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-30
EXPORT - OPERATION, ANTENNA MODULE ........................... 8A-10
EXPORT - OPERATION, DOOR CYLINDER LOCK SWITCH ....................... 8N-22
EXPORT - OPERATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - OPERATION, QUARTER GLASS INTEGRAL ANTENNA .................. 8A-13
EXPORT - QUARTER GLASS INTEGRAL ANTENNA .......................... 8A-13
EXPORT - REMOVAL ................... 5-67
EXPORT - REMOVAL ................... 2-11
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - REMOVAL, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ALIGNMENT ......8L-9
EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT ALIGNMENT ..........8L-15
EXTENSION, INSTALLATION - REAR A/C EVAPORATOR LINE .................. 24-100
EXTENSION, REMOVAL - REAR A/C EVAPORATOR LINE ................... 24-99
EXTENSION TRIM - INSTALLATION, A-PILLAR LOWER .................... 23-79
EXTENSION TRIM - REMOVAL, A-PILLAR LOWER ............................ 23-79
EXTERIOR - DESCRIPTION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - OPERATION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - WARNING, LAMPS/ LIGHTING ........................... 8L-3
EXTERIOR HANDLE - INSTALLATION .....23-22,
23-40
EXTERIOR HANDLE - REMOVAL ....23-21,23-40
EXTERIOR HANDLE SWITCH - DESCRIPTION ....................... 8N-10
EXTERIOR HANDLE SWITCH - INSTALLATION ...................... 8N-10
EXTERIOR HANDLE SWITCH - OPERATION ......................... 8N-10EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-10
EXTERIOR LAMPS, SPECIFICATIONS
......8L-3
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - REMOVAL ................23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - REMOVAL ................23-51
FACTOR SETTING - STANDARD PROCEDURE, PINION .................8E-15
FAILED PARK SWITCH - DIAGNOSIS AND TESTING ............................ 8R-2
FAN - DESCRIPTION, RADIATOR ..........7-29
FAN - INSTALLATION, RADIATOR .........7-30
FAN - OPERATION, RADIATOR ...........7-29
FAN - REMOVAL, RADIATOR .............7-30
FAN MOTOR - DIAGNOSIS AND TESTING, RADIATOR ................... 7-30
FAN RELAY - DESCRIPTION, RADIATOR ....7-31
FAN RELAY - INSTALLATION, RADIATOR . . . 7-31
FAN RELAY - OPERATION, RADIATOR ......7-31
FAN RELAY - REMOVAL, RADIATOR .......7-31
FASCIA - INSTALLATION, FRONT .........13-1
FASCIA - INSTALLATION, REAR ..........13-4
FASCIA - REMOVAL, FRONT .............13-1
FASCIA - REMOVAL, REAR ..............13-4
FASCIA - SCUFF PAD - INSTALLATION, REAR ............................... 13-5
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-5
FASTENER TORQUE, SPECIFICATIONS - ABS ................................ 5-91
FASTENER TORQUE, SPECIFICATIONS - BRAKE ...............................5-9
FASTENER TORQUE, SPECIFICATIONS - COLUMN ........................... 19-17
FASTENER TORQUE, SPECIFICATIONS - FRONT SUSPENSION ...................2-3
FASTENER TORQUE, SPECIFICATIONS - POWER STEERING .................... 19-9
FASTENER TORQUE, SPECIFICATIONS - REAR SUSPENSION ................... 2-28
FEED CIRCUIT RESISTANCE TEST - DIAGNOSIS AND TESTING ..............8F-35
FEED CIRCUIT TEST - DIAGNOSIS AND TESTING ........................... 8F-36
FENDER - INSTALLATION, FRONT ........23-52
FENDER - REMOVAL, FRONT ...........23-51
FFV REPLACEMENT PARTS - DESCRIPTION ........................ 14-2
FILL - DIAGNOSIS AND TESTING, VEHICLE DOES NOT .................. 25-17
FILL DOOR - INSTALLATION, FUEL .......23-52
FILL DOOR - REMOVAL, FUEL ..........23-52
FILL DOOR BLOCKER LATCH - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL .................23-54
FILL DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL ..................... 23-54
FILL/CHECK LOCATIONS - DESCRIPTION, FLUID ...............................0-7
FILLER CAP - DESCRIPTION, FUEL .......25-13
FILLER CAP - OPERATION, FUEL ........25-13
FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP TO ............7-28
FILLER TUBE - INSTALLATION, FUEL TANK .............................. 14-17
FILLER TUBE - REMOVAL, FUEL TANK ....14-16
FILLING - STANDARD PROCEDURE, COOLING SYSTEM .....................7-4
FILLING, STANDARD PROCEDURE - REAR HEATER CORE .................24-102
FILTER - DESCRIPTION, AIR ............24-42
FILTER - DESCRIPTION, OIL .............9-54
FILTER - INSTALLATION, AIR ...........24-43
FILTER - INSTALLATION, INLET ..........14-17
FILTER - INSTALLATION, OIL .......9-141,9-54
FILTER - REMOVAL, AIR ...............24-42
FILTER - REMOVAL, INLET .............14-17
FILTER - REMOVAL, OIL ...........9-141,9-54
12 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

HCU (HYDRAULIC CONTROL UNIT) -OPERATION ......................... 5-101
HEAD - CLEANING, CYLINDER ......9-103,9-26
HEAD - DESCRIPTION, CYLINDER . . . 9-102,9-25
HEAD - INSPECTION, CYLINDER .....9-104,9-27
HEAD - INSTALLATION, CYLINDER . . . 9-104,9-27
HEAD - REMOVAL, CYLINDER ......9-103,9-26
HEAD COVER - CLEANING, CYLINDER .....9-31
HEAD COVER - INSPECTION, CYLINDER . . . 9-31
HEAD COVER - INSTALLATION, CYLINDER ........................... 9-32
HEAD COVER - LEFT - INSTALLATION, CYLINDER .......................... 9-107
HEAD COVER - LEFT - REMOVAL, CYLINDER .......................... 9-107
HEAD COVER - REMOVAL, CYLINDER .....9-31
HEAD COVER - RIGHT - INSTALLATION, CYLINDER .......................... 9-106
HEAD COVER - RIGHT - REMOVAL, CYLINDER .......................... 9-106
HEAD COVER(S) - DESCRIPTION, CYLINDER .......................... 9-105
HEAD GASKET - DIAGNOSIS AND TESTING, CYLINDER ..............9-102,9-25
HEAD OFF - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD OFF - REMOVAL, CYLINDER . . . 9-109,9-33
HEAD ON - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD ON - REMOVAL, CYLINDER . . . 9-111,9-33
HEADER TRIM - INSTALLATION, REAR ....23-96
HEADER TRIM - REMOVAL, REAR .......23-96
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-11
HEADLAMP - INSTALLATION ............8L-13
HEADLAMP - REMOVAL ...............8L-12
HEADLAMP SWITCH - DIAGNOSIS AND TESTING ........................... 8L-13
HEADLAMP SWITCH - INSTALLATION ....8L-13
HEADLAMP SWITCH - REMOVAL ........8L-13
HEADLAMP UNIT - EXPORT - INSTALLATION ....................... 8L-17
HEADLAMP UNIT - EXPORT - REMOVAL . . 8L-17
HEADLAMP UNIT - INSTALLATION .......8L-15
HEADLAMP UNIT - REMOVAL ...........8L-15
HEADLAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .............8L-15
HEADLAMP UNIT ALIGNMENT - STANDARD PROCEDURE ...............8L-14
HEADLINER - INSTALLATION ...........23-92
HEADLINER - REMOVAL ...............23-91
HEADREST - INSTALLATION ...........23-106
HEADREST - REMOVAL ...............23-106
HEADREST SLEEVE - INSTALLATION ....23-107
HEADREST SLEEVE - REMOVAL ........23-107
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION .......23-131
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - REMOVAL ...........23-131
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION .......23-153
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - REMOVAL ...........23-152
HEAT DUCT - INSTALLATION, REAR FLOOR ............................. 24-63
HEAT DUCT - REMOVAL, REAR FLOOR . . . 24-63
HEAT SHIELDS - DESCRIPTION ..........11-7
HEAT SHIELDS - INSTALLATION ..........11-7
HEAT SHIELDS - OPERATION ............11-7
HEAT SHIELDS - REMOVAL .............11-7
HEAT STAKING - STANDARD PROCEDURE ......................... 23-9
HEATED GLASS - DESCRIPTION ..........8G-1
HEATED GLASS - OPERATION ...........8G-2
HEATED MIRRORS - DESCRIPTION .......8G-6
HEATED MIRRORS - OPERATION .........8G-6
HEATED SEAT ELEMENTS - DESCRIPTION ....................... 8G-11
HEATED SEAT ELEMENTS - OPERATION . . 8G-11
HEATED SEAT ELEMENTS, DIAGNOSIS AND TESTING ....................... 8G-11
HEATED SEAT MODULE - DESCRIPTION ....8E-8
HEATED SEAT MODULE - OPERATION .....8E-8
HEATED SEAT MODULE, DIAGNOSIS AND TESTING ............................ 8E-9
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-13
HEATED SEAT SENSOR - OPERATION ....8G-13
HEATED SEAT SENSOR, DIAGNOSIS AND TESTING ........................... 8G-13HEATED SEAT SWITCH - DESCRIPTION
....8G-8
HEATED SEAT SWITCH - OPERATION ......8G-9
HEATED SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER .................... 8G-9
HEATED SEAT SYSTEM - DESCRIPTION ....8G-7
HEATED SEAT SYSTEM - OPERATION .....8G-8
HEATED SEAT SYSTEM, DIAGNOSIS AND TESTING ............................ 8G-8
HEATER - DESCRIPTION, CABIN ........24-113
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-20
HEATER - INSTALLATION, ENGINE BLOCK .............................. 7-21
HEATER - OPERATION, ENGINE BLOCK ....7-20
HEATER - REMOVAL, ENGINE BLOCK ......7-21
HEATER AND AIR CONDITIONER, DESCRIPTION ........................ 24-1
HEATER AND AIR CONDITIONER, OPERATION .......................... 24-4
HEATER CONTROL - DESCRIPTION, A/C . . . 24-19
HEATER CORE - DESCRIPTION ....24-102,24-83
HEATER CORE - OPERATION ......24-102,24-84
HEATER CORE FILLING, STANDARD PROCEDURE - REAR .................24-102
HEATER CORE, INSTALLATION - FRONT . . . 24-86
HEATER CORE, REMOVAL - FRONT ......24-85
HEATER CORE TUBES, INSTALLATION - FRONT ............................. 24-85
HEATER CORE TUBES, REMOVAL - FRONT ............................. 24-84
HEATER, DIAGNOSIS AND TESTING - SUPPLEMENTAL CABIN ...............24-114
HEATER HOSES - INSTALLATION . 24-105,24-119
HEATER HOSES - REMOVAL .....24-104,24-119
HEATER INLET HOSE - INSTALLATION ....24-87
HEATER INLET HOSE - REMOVAL ........24-86
HEATER PERFORMANCE TEST, DIAGNOSIS AND TESTING .............24-10
HEATER PIPES - INSTALLATION ........24-120
HEATER PIPES - REMOVAL ............24-119
HEATER RETURN HOSE - INSTALLATION . . 24-89
HEATER RETURN HOSE - REMOVAL ......24-88
HEATER TESTING - DIAGNOSIS AND TESTING, ENGINE BLOCK ...............7-21
HEATER TUBES, INSTALLATION - UNDERBODY ....................... 24-112
HEATER TUBES, REMOVAL - UNDERBODY ....................... 24-109
HEATER UNIT - INSTALLATION .........24-122
HEATER UNIT - REMOVAL .............24-121
HEATER WIRING - INSTALLATION ......24-122
HEATER WIRING - REMOVAL ..........24-122
HEAVY DUTY, CARGO - INSTALLATION, AWD ............................... 2-36
HEAVY DUTY, CARGO - REMOVAL, AWD . . . 2-36
HEIGHT ADJUSTE R-BORC-PILLAR -
INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTE R-BORC-PILLAR -
REMOVAL, SEAT BELT ................8O-38
HEIGHT ADJUSTER KNOB - INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTER KNOB - REMOVAL, SEAT BELT ......................... 8O-38
HEIGHT MEASUREMENT - STANDARD PROCEDURE, CURB ................... 2-55
HIGH AND LOW LIMITS, DESCRIPTION ....25-9
HIGH MOUNTED STOP LAMP - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP - REMOVAL, CENTER .................... 8L-6
HIGH MOUNTED STOP LAMP UNIT - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP UNIT - REMOVAL, CENTER .................... 8L-6
HIGH PRESSURE RELIEF VALVE, DESCRIPTION ....................... 24-72
HIGH PRESSURE RELIEF VALVE, OPERATION ......................... 24-72
HIGH SPEED OPERATION - STANDARD PROCEDURE, TIRE PRESSURE ..........22-17
HINGE - INSTALLATION ......23-18,23-40,23-62
HINGE - INSTALLATION, CENTER ........23-24
HINGE - INSTALLATION, LOWER ........23-28
HINGE - INSTALLATION, UPPER .........23-36
HINGE - REMOVAL .........23-17,23-40,23-62
HINGE - REMOVAL, BENCH SEAT BACK . . 23-146
HINGE - REMOVAL, CENTER ............23-24
HINGE - REMOVAL, LOWER ............23-28
HINGE - REMOVAL, UPPER .............23-36HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK ............................. 23-146
HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-146
HOISTING - STANDARD PROCEDURE ......0-24
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - REMOVAL, BATTERY ......8F-16
HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD/CUP .......23-151
HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET
SEAT SIDE SHIELD/CUP ..............23-151
HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP ......23-160
HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP ................... 23-160
HOLDER - INSTALLATION, CUP .........23-65
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD - NO CUP . . . 23-143
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD/CUP .......23-142
HOLDER - REMOVAL, CUP .............23-65
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD - NO CUP ..........23-143
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD/CUP ..............23-141
HOLDING CLUTCHES - DESCRIPTION . . . 21-236, 21-86
HOLDING CLUTCHES - OPERATION .....21-236,
21-86
HONING - STANDARD PROCEDURE, CYLINDER BORE ................. 9-115,9-36
HOOD - INSTALLATION ................23-63
HOOD - REMOVAL .................... 23-62
HOOD AJAR SWITCH - EXPORT - INSTALLATION ....................... 8Q-3
HOOD AJAR SWITCH - EXPORT - REMOVAL ........................... 8Q-3
HORN CHIRP PREFERENCE - STANDARD PROCEDURE ........................ 8N-24
HORN, DIAGNOSIS AND TESTING ........8H-3
HORN SWITCH - DESCRIPTION ..........8H-4
HORN SYSTEM - DESCRIPTION ..........8H-1
HORN SYSTEM - OPERATION ............8H-1
HORN SYSTEM, DIAGNOSIS AND TESTING ............................ 8H-1
HOSE - INSTALLATION, HEATER INLET ....24-87
HOSE - INSTALLATION, HEATER RETURN . 24-89
HOSE - REMOVAL, HEATER INLET .......24-86
HOSE - REMOVAL, HEATER RETURN .....24-88
HOSE CLAMPS - DESCRIPTION ...........7-1
HOSE CLAMPS - OPERATION .............7-2
HOSES - DESCRIPTION, BRAKE TUBES ....5-14
HOSES - INSPECTION, BRAKE TUBES .....5-14
HOSES - INSTALLATION, HEATER . 24-105,24-119
HOSES - INSTALLATION, WASHER .......8R-12
HOSES - OPERATION, BRAKE TUBES ......5-14
HOSES - REMOVAL, HEATER ....24-104,24-119
HOSES - REMOVAL, WASHER ..........8R-11
HOSES AND CLAMP - STANDARD PROCEDURE ......................... 14-7
HOUSING - INSTALLATION, AIR CLEANER ....................... 9-102,9-25
HOUSING - INSTALLATION, HVAC ........24-62
HOUSING - REMOVAL, AIR CLEANER . 9-101,9-25
HOUSING - REMOVAL, HVAC ...........24-60
HOUSING FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER . . . 21-154,
21-9
HUB / BEARING - DESCRIPTION .......2-30,2-5
HUB / BEARING - INSTALLATION ......2-33,2-5
HUB / BEARING - OPERATION ........2-30,2-5
HUB / BEARING - REMOVAL ..........2-31,2-5
HUB AND BEARING - DIAGNOSIS AND TESTING ......................... 2-31,2-5
HVAC - LWB - INSTALLATION, SEAT BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR .........8O-41
HVAC - LWB - REMOVAL, SEAT BELT & RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR ...............8O-41
HVAC HOUSING - INSTALLATION ........24-62
HVAC HOUSING - REMOVAL ............24-60
HVAC LOUVER - INSTALLATION, REAR . . . 23-97
HVAC LOUVER - REMOVAL, REAR .......23-96
16 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

STORAGE BIN GUIDE - INSTALLATION,UNDER SEAT ....................... 23-150
STORAGE BIN GUIDE - REMOVAL, UNDER SEAT ....................... 23-150
STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER SEAT ..........23-150
STORAGE BIN LOCK/LATCH - REMOVAL, UNDER SEAT ....................... 23-150
STRAP - INSTALLATION, CHECK .........23-15
STRAP - INSTALLATION, FRONT SEAT BACK ASSIST ...................... 23-112
STRAP - REMOVAL, CHECK ............23-15
STRAP - REMOVAL, FRONT SEAT BACK ASSIST ........................... 23-112
STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW .....23-158
STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW .........23-158
STRIKER - INSTALLATION, CENTER ......23-28
STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER LATCH ...............23-53
STRIKER - INSTALLATION, GLOVE BOX LATCH ............................. 23-66
STRIKER - INSTALLATION, HOLD OPEN LATCH ............................. 23-26
STRIKER - INSTALLATION, LATCH . . 23-19,23-42, 23-64
STRIKER - INSTALLATION, REAR LATCH . . 23-29
STRIKER - REMOVAL, CENTER ..........23-28
STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER LATCH ..................... 23-53
STRIKER - REMOVAL, GLOVE BOX LATCH ............................. 23-66
STRIKER - REMOVAL, HOLD OPEN LATCH ............................. 23-26
STRIKER - REMOVAL, LATCH . 23-19,23-41,23-64
STRIKER - REMOVAL, REAR LATCH ......23-29
STRIPPED THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD ..............9-147
STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-FLOOR ONLY -
SPECIFICATIONS .................... 23-228
STRUCTURAL ADHESIVE LOCATIONS - SPECIFICATIONS .................... 23-218
STRUCTURAL COLLAR - INSTALLATION ....9-49
STRUCTURAL COLLAR - REMOVAL .......9-49
STRUT - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT GAS .....23-139
STRUT - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT GAS .........23-138
STRUT ASSEMBLY - ASSEMBLY ..........2-23
STRUT ASSEMBLY - DESCRIPTION .......2-19
STRUT ASSEMBLY - DIAGNOSIS AND TESTING ............................ 2-20
STRUT ASSEMBLY - DISASSEMBLY .......2-21
STRUT ASSEMBLY - INSTALLATION .......2-25
STRUT ASSEMBLY - OPERATION .........2-19
STRUT ASSEMBLY - REMOVAL ...........2-20
STUDS - FRONT - INSTALLATION, WHEEL MOUNTING ................... 22-21
STUDS - FRONT - REMOVAL, WHEEL MOUNTING ......................... 22-21
STUDS - REAR - INSTALLATION, WHEEL MOUNTING ......................... 22-22
STUDS - REAR - REMOVAL, WHEEL MOUNTING ......................... 22-22
SUCTION LINE - INSTALLATION . . . 24-107,24-97
SUCTION LINE - REMOVAL .......24-106,24-96
SUN VISOR - INSTALLATION ...........23-99
SUN VISOR - REMOVAL ...............23-99
SUN VISOR SUPPORT - INSTALLATION . . . 23-99
SUN VISOR SUPPORT - REMOVAL .......23-99
SUNROOF - DESCRIPTION ............23-169
SUNROOF ASSEMBLY - INSTALLATION . . 23-173
SUNROOF ASSEMBLY - REMOVAL ......23-173
SUNROOF DIAGNOSIS AND TESTING, DIAGNOSIS AND TESTING ............23-169
SUNROOF GLASS PANEL ADJUSTMENT, ADJUSTMENTS ..................... 23-173
SUNROOF MOTOR - INSTALLATION .....23-174
SUNROOF MOTOR - REMOVAL .........23-174
SUNROOF SWITCH - INSTALLATION .....23-176
SUNROOF SWITCH - REMOVAL ........23-176
SUNSHADE - INSTALLATION ...........23-173
SUNSHADE - REMOVAL ..............23-173
SUPPLEMENTAL CABIN HEATER, DIAGNOSIS AND TESTING ............24-114SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT .............................. 8E-15
SUPPORT - INSTALLATION, LUMBAR ....23-150
SUPPORT - INSTALLATION, SUN VISOR . . . 23-99
SUPPORT - REMOVAL, LUMBAR .......23-150
SUPPORT - REMOVAL, SUN VISOR ......23-99
SUPPORT CYLINDER - INSTALLATION ....23-43
SUPPORT CYLINDER - REMOVAL ........23-42
SUPPORT PLATE - DRUM BRAKE - INSTALLATION ........................ 5-61
SUPPORT PLATE - DRUM BRAKE - REMOVAL ........................... 5-61
SUPPRESSION COMPONENTS - DESCRIPTION, RADIO NOISE ...........8A-15
SUPPRESSION COMPONENTS - OPERATION, RADIO NOISE .............8A-15
SURFACE PREPARATION - STANDARD PROCEDURE, ENGINE GASKET .......9-11,9-87
SUSPENSION - DESCRIPTION, FRONT ......2-2
SUSPENSION - DESCRIPTION, REAR ......2-26
SUSPENSION - OPERATION, FRONT ........2-2
SUSPENSION AND STEERING - DIAGNOSIS AND TESTING ..............2-50
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - FRONT ................2-3
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - REAR ................2-28
SUSPENSION, SPECIAL TOOLS - FRONT ....2-3
SUSPENSION, SPECIAL TOOLS - REAR ....2-28
SWITCH - DESCRIPTION .................8P-5
SWITCH - DESCRIPTION, B-PILLAR ......8N-52
SWITCH - DESCRIPTION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - DESCRIPTION, BRAKE LAMP ....8L-4
SWITCH - DESCRIPTION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - DESCRIPTION, FULL OPEN ....8N-11,
8N-52
SWITCH - DESCRIPTION, HEATED SEAT . . . 8G-8
SWITCH - DESCRIPTION, HORN ..........8H-4
SWITCH - DESCRIPTION, MEMORY ......8N-36
SWITCH - DESCRIPTION, OIL PRESSURE . 9-144
SWITCH - DESCRIPTION, REAR WINDOW DEFOGGER .................. 8G-4
SWITCH - DESCRIPTION, REAR WIPER/WASHER ..................... 8R-10
SWITCH - DESCRIPTION, SEAT .........8N-34
SWITCH - DIAGNOSIS AND TESTING, BRAKE LAMP ........................ 8L-4
SWITCH - DIAGNOSIS AND TESTING, FAILED PARK ........................ 8R-2
SWITCH - DIAGNOSIS AND TESTING, FRONT WIPER/WASHER ................8R-2
SWITCH - DIAGNOSIS AND TESTING, HEADLAMP ......................... 8L-13
SWITCH - DIAGNOSIS AND TESTING, MULTI-FUNCTION .................... 8L-18
SWITCH - DIAGNOSIS AND TESTING, TRACTION CONTROL ................... 5-94
SWITCH - EXPORT - DESCRIPTION, DOOR CYLINDER LOCK ...............8N-22
SWITCH - EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - INSTALLATION, HOOD AJAR ......................... 8Q-3
SWITCH - EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR ...........8N-30
SWITCH - EXPORT - OPERATION, DOOR CYLINDER LOCK ..................... 8N-22
SWITCH - EXPORT - OPERATION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - REMOVAL, HOOD AJAR ............................... 8Q-3
SWITCH - EXPORT - REMOVAL, POWER FOLDAWAY MIRROR .................. 8N-29
SWITCH - INSTALLATION ...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - INSTALLATION, B-PILLAR .....8N-52
SWITCH - INSTALLATION, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-5
SWITCH - INSTALLATION, CENTER CONSOLE LAMP ..................... 8L-21
SWITCH - INSTALLATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - INSTALLATION, FULL OPEN ....8N-11 SWITCH - INSTALLATION, GLOVE BOX
LAMP .............................. 8L-22
SWITCH - INSTALLATION, HEADLAMP ....8L-13
SWITCH - INSTALLATION, IGNITION ......19-19
SWITCH - INSTALLATION, MULTI- FUNCTION .......................... 8L-18
SWITCH - INSTALLATION, OIL PRESSURE ..................... 9-144,9-56
SWITCH - INSTALLATION, SUNROOF ....23-176
SWITCH - INSTALLATION, TRACTION CONTROL ........................... 5-95
SWITCH - INSTALLATION, WASHER FLUID LEVEL ........................ 8R-11
SWITCH - OPERATION .................8P-5
SWITCH - OPERATION, B-PILLAR ........8N-52
SWITCH - OPERATION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - OPERATION, BRAKE LAMP ......8L-4
SWITCH - OPERATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - OPERATION, FULL OPEN . 8N-11,8N-52
SWITCH - OPERATION, HEATED SEAT .....8G-9
SWITCH - OPERATION, MEMORY ........8N-36
SWITCH - OPERATION, OIL PRESSURE . . . 9-144
SWITCH - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-4
SWITCH - OPERATION, REAR WIPER/ WASHER ........................... 8R-11
SWITCH - OPERATION, SEAT ...........8N-34
SWITCH - REMOVAL .................... 8P-5
SWITCH - REMOVAL, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - REMOVAL, B-PILLAR .........8N-52
SWITCH - REMOVAL, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - REMOVAL, BRAKE LAMP .......8L-5
SWITCH - REMOVAL, CENTER CONSOLE LAMP .............................. 8L-21
SWITCH - REMOVAL, EXTERIOR HANDLE . 8N-10
SWITCH - REMOVAL, FULL OPEN .......8N-11
SWITCH - REMOVAL, GLOVE BOX LAMP . . 8L-22
SWITCH - REMOVAL, HEADLAMP ........8L-13
SWITCH - REMOVAL, IGNITION .........19-17
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE ....9-144,
9-56
SWITCH - REMOVAL, SUNROOF ........23-176
SWITCH - REMOVAL, TRACTION CONTROL ........................... 5-95
SWITCH - REMOVAL, WASHER FLUID LEVEL ............................. 8R-11
SWITCH ASSY - DESCRIPTION, SOLENOID/PRESSURE ..........21-117,21-268
SWITCH ASSY - INSTALLATION, SOLENOID/PRESSURE ..........21-119,21-270
SWITCH ASSY - OPERATION, SOLENOID/ PRESSURE .................. 21-118,21-268
SWITCH ASSY - REMOVAL, SOLENOID/ PRESSURE .................. 21-118,21-269
SWITCH, DIAGNOSIS AND TESTING - DOOR LOCK ........................ 8N-23
SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED SEAT .................8G-9
SWITCH, DIAGNOSIS AND TESTING - DRIVER SEAT ....................... 8N-34
SWITCH, DIAGNOSIS AND TESTING - MEMORY ........................... 8N-37
SWITCH, DIAGNOSIS AND TESTING - REMOTE ........................... 8N-30
SWITCH, DIAGNOSIS AND TESTING - WINDOW ........................... 8N-63
SWITCH, EXPORT - DOOR CYLINDER LOCK .............................. 8N-22
SWITCHES - DESCRIPTION, REMOTE .....8A-16
SWITCHES - OPERATION, REMOTE ......8A-16
SWITCHES, DIAGNOSIS AND TESTING - REMOTE ........................... 8A-16
SYMBOLS - DESCRIPTION, INTERNATIONAL .......................0-1
SYNCHRONIZING CABLE ADJUSTMENT, INSTALLATION ................ 23-105,23-147
TAIL LAMP - INSTALLATION ............8L-19
TAIL LAMP - REMOVAL ................8L-18
TAIL LAMP UNIT - INSTALLATION .......8L-19
TAIL LAMP UNIT - REMOVAL ...........8L-19
TANK - DESCRIPTION, FUEL ............14-12
TANK - OPERATION, FUEL ..............14-12
RS INDEX31
Description Group-Page Description Group-Page Description Group-Page

TUBE - REMOVAL, DRAIN.............23-172
TUBE - REMOVAL, EXHAUST ..........24-116
TUBE - REMOVAL, FUEL TANK FILLER ....14-16
TUBES AND HOSES - DESCRIPTION, BRAKE .............................. 5-14
TUBES AND HOSES - INSPECTION, BRAKE .............................. 5-14
TUBES AND HOSES - OPERATION, BRAKE .............................. 5-14
TUBES, INSTALLATION - FRONT HEATER CORE .............................. 24-85
TUBES, INSTALLATION - UNDERBODY HEATER ........................... 24-112
TUBES, REMOVAL - FRONT HEATER CORE .............................. 24-84
TUBES, REMOVAL - UNDERBODY HEATER ........................... 24-109
TUBING AND FITTINGS, STANDARD PROCEDURE - HANDLING ..............24-69
TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE KEY
LOCK .............................. 23-90
TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK ............23-90
TURN SIGNAL SYSTEM - DESCRIPTION . . . 8L-17
TURN SIGNAL SYSTEM - OPERATION ....8L-17
UNDER SEAT STORAGE BIN - INSTALLATION ...................... 23-149
UNDER SEAT STORAGE BIN - REMOVAL . 23-149
UNDER SEAT STORAGE BIN GUIDE - INSTALLATION ...................... 23-150
UNDER SEAT STORAGE BIN GUIDE - REMOVAL ......................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - INSTALLATION .................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - REMOVAL ........................ 23-150
UNDERBODY HEATER TUBES, INSTALLATION ...................... 24-112
UNDERBODY HEATER TUBES, REMOVAL . 24-109
UNDERBODY LINES - DESCRIPTION .....24-108
UNDERBODY LINES - OPERATION ......24-108
UNDERBODY REFRIGERANT LINES, INSTALLATION ...................... 24-112
UNDERBODY REFRIGERANT LINES, REMOVAL ......................... 24-110
UNIT - DESCRIPTION, LOWER DRIVE ....8N-53
UNIT - EXPORT - INSTALLATION, HEADLAMP ......................... 8L-17
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-17
UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - INSTALLATION, HEADLAMP .......8L-15
UNIT - INSTALLATION, HEATER ........24-122
UNIT - INSTALLATION, LOWER DRIVE ....8N-54
UNIT - INSTALLATION, TAIL LAMP .......8L-19
UNIT - OPERATION, LOWER DRIVE ......8N-53
UNIT - REMOVAL, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - REMOVAL, HEADLAMP ..........8L-15
UNIT - REMOVAL, HEATER ............24-121
UNIT - REMOVAL, LOWER DRIVE .......8N-53
UNIT - REMOVAL, TAIL LAMP ...........8L-19
UNIT / SENSOR - DESCRIPTION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - INSTALLATION, FUEL LEVEL SENDING ...................... 14-6
UNIT / SENSOR - OPERATION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - REMOVAL, FUEL LEVEL SENDING ...................... 14-5
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG
LAMP ............................... 8L-9
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP ....8L-15
UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP .........8L-9
UNIT ALIGNMENT - STANDARD PROCEDURE, HEADLAMP ..............8L-14
UNIT FLUID - DESCRIPTION, AWD POWER TRANSFER .....................0-6
UNIT TRACK & RACK - DESCRIPTION, LOWER DRIVE ...................... 8N-57
UNIT TRACK & RACK - INSTALLATION, LOWER DRIVE ...................... 8N-58
UNIT TRACK & RACK - OPERATION, LOWER DRIVE ...................... 8N-57UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE ...................... 8N-57
UNIVERSAL TRANSMITTER - DESCRIPTION ....................... 8M-11
UNIVERSAL TRANSMITTER, DIAGNOSIS AND TESTING ....................... 8M-11
UPPER - INSPECTION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, SHROUD .......19-22
UPPER - REMOVAL, INTAKE MANIFOLD ....9-60
UPPER - REMOVAL, SHROUD ...........19-22
UPPER HINGE - INSTALLATION .........23-36
UPPER HINGE - REMOVAL .............23-36
UPPER INTAKE MANIFOLD - INSTALLATION ....................... 9-149
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-148
UPPER RADIATOR CROSSMEMBER - INSTALLATION ....................... 23-56
UPPER RADIATOR CROSSMEMBER - REMOVAL .......................... 23-56
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-80
UPPER TRIM - REMOVAL, B-PILLAR .....23-80
UPSTREAM 1/1 - 2.4L - INSTALLATION . . . 14-38
UPSTREAM 1/1 - 2.4L - REMOVAL .......14-37
UPSTREAM 1/1 - 3.3/3.8L - INSTALLATION ....................... 14-39
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL ....14-38
USE WIRING DIAGRAMS - DESCRIPTION, HOW TO .............8W-01-1
USING PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING
CLEARANCE ..................... 9-12,9-86
VAC LEAK DETECTION ASSY - INSTALLATION, NATURAL ..............25-14
VAC LEAK DETECTION ASSY - REMOVAL, NATURAL .................. 25-14
VACUUM PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD ........9-148
VACUUM RESERVOIR - DESCRIPTION .....8P-6
VACUUM RESERVOIR - INSTALLATION ....8P-6
VACUUM RESERVOIR - OPERATION .......8P-6
VACUUM RESERVOIR - REMOVAL ........8P-6
VALVE - DESCRIPTION ................25-23
VALVE - DESCRIPTION, A/C EXPANSION . 24-100
VALVE - DESCRIPTION, EXPANSION ......24-81
VALVE - DESCRIPTION, PCV ............25-18
VALVE - INSTALLATION, OIL PRESSURE RELIEF ............................. 9-144
VALVE - OPERATION ..................25-23
VALVE - OPERATION, A/C EXPANSION . . . 24-100
VALVE - OPERATION, EXPANSION .......24-81
VALVE - OPERATION, PCV ..............25-18
VALVE - REMOVAL, OIL PRESSURE RELIEF ............................. 9-143
VALVE BODY - ASSEMBLY ......21-139,21-291
VALVE BODY - DESCRIPTION ....21-132,21-283
VALVE BODY - DISASSEMBLY ....21-135,21-286
VALVE BODY - INSTALLATION ....21-144,21-295
VALVE BODY - OPERATION ......21-132,21-283
VALVE BODY - REMOVAL .......21-133,21-284
VALVE CORE - DESCRIPTION, SERVICE PORT.............................. 24-95
VALVE CORE - INSTALLATION, SERVICE PORT.............................. 24-95
VALVE CORE - REMOVAL, SERVICE PORT.............................. 24-95
VALVE, DESCRIPTION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE, DIAGNOSIS AND TESTING - FRONT A/C EXPANSION ...............24-82
VALVE, DIAGNOSIS AND TESTING - REAR A/C EXPANSION ...............24-101
VALVE (HEIGHT SENSING) - DESCRIPTION, PROPORTIONING .........5-53
VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING, PROPORTIONING .........5-54
VALVE (HEIGHT SENSING) - INSTALLATION, PROPORTIONING .........5-55
VALVE (HEIGHT SENSING) - OPERATION, PROPORTIONING ..................... 5-53
VALVE (HEIGHT SENSING) - REMOVAL, PROPORTIONING ..................... 5-55
VALVE, OPERATION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE SEATS - STANDARD PROCEDURE, REFACING VALVES ................... 9-107VALVE SPRINGS - DESCRIPTION
........9-109
VALVE SPRINGS - OPERATION ..........9-109
VALVE STEM SEALS - DESCRIPTION .....9-114
VALVE STEM SEALS - INSTALLATION .....9-115
VALVE STEM SEALS - REMOVAL ........9-115
VALVE TIMING VERIFICATION - STANDARD PROCEDURE ...............9-155
VALVES - OPERATION, HYDRAULIC CIRCUITS ............................ 5-95
VALVES & SEATS - CLEANING, INTAKE/EXHAUST ................ 9-108,9-33
VALVES & SEATS - DESCRIPTION, INTAKE/EXHAUST ................ 9-107,9-33
VALVES & SEATS - INSPECTION, INTAKE/EXHAUST .................... 9-108
VALVES & SEATS - INSTALLATION, INTAKE/EXHAUST .................... 9-109
VALVES & SEATS - OPERATION, INTAKE/EXHAUST .................... 9-107
VALVES & SEATS - REMOVAL, INTAKE/EXHAUST .................... 9-108
VALVES AND VALVE SEATS - STANDARD PROCEDURE, REFACING ...............9-107
VANITY LAMP - INSTALLATION .........8L-24
VANITY LAMP - REMOVAL .............8L-24
VAPOR CANISTER - DESCRIPTION .......25-19
VAPOR CANISTER - OPERATION .........25-19
VARIABLE BRAKE PROPORTIONING - DESCRIPTION, ELECTRONIC .............5-88
VARIABLE BRAKE PROPORTIONING - OPERATION, ELECTRONIC ................5-89
VARIATION ADJUSTMENT, STANDARD PROCEDURE - COMPASS ...............8M-5
VEHICLE DOES NOT FILL - DIAGNOSIS AND TESTING ....................... 25-17
VEHICLE EMISSION CONTROL INFORMATION LABEL, DESCRIPTION ......25-1
VEHICLE IDENTIFICATION - DESCRIPTION ........................ 23-1
VEHICLE INFO CENTER - DESCRIPTION, ELECTRONIC ........................ 8M-7
VEHICLE INFO CENTER - OPERATION, ELECTRONIC ........................ 8M-7
VEHICLE INFORMATION CENTER, DIAGNOSIS AND TESTING -
ELECTRONIC ........................ 8M-8
VEHICLE INFORMATION CENTER PROGRAMMING, STANDARD
PROCEDURE - ELECTRONIC ............8M-8
VEHICLE THEFT SECURITY - DESCRIPTION ........................ 8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
VENT WINDOW MOTOR, DIAGNOSIS AND TESTING ....................... 8N-62
VERIFICATION - STANDARD PROCEDURE, VALVE TIMING ...........9-155
VIBRATION - DIAGNOSIS AND TESTING, TIRE AND WHEEL ..................... 22-1
VIBRATION DAMPER - INSTALLATION ....9-132,
9-49
VIBRATION DAMPER - REMOVAL ....9-132,9-48
VIDEO SCREEN - DESCRIPTION .........8A-20
VIDEO SCREEN - INSTALLATION ........8A-20
VIDEO SCREEN - OPERATION ...........8A-20
VIDEO SCREEN - REMOVAL ............8A-20
VIEW MIRROR - INSTALLATION, REAR . . . 23-97
VIEW MIRROR - INSTALLATION, SIDE ....23-60
VIEW MIRROR - REMOVAL, REAR .......23-97
VIEW MIRROR - REMOVAL, SIDE ........23-60
VISOR - INSTALLATION, SUN ...........23-99
VISOR - REMOVAL, SUN ...............23-99
VISOR SUPPORT - INSTALLATION, SUN . . . 23-99
VISOR SUPPORT - REMOVAL, SUN ......23-99
VOLT SUPPLY - PCM OUTPUT - OPERATION, 5 ....................... 8E-15
VOLTAGE DROP - STANDARD PROCEDURE, TESTING FOR A .......8W-01-10
VOLTAGE POTENTIAL - STANDARD PROCEDURE, TESTING OF ...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION ....8F-30
VOLTAGE REGULATOR - OPERATION .....8F-30
VOLTAGE TEST, STANDARD PROCEDURE - OPEN-CIRCUIT ..................... 8F-13
VTSS/SKIS INDICATOR LAMP - DESCRIPTION ........................ 8Q-8
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page