CHRYSLER SEBRING CONVERTIBLE 2005 2.G Manual Online

Canadian Programming/Gate Programming
Canadian frequency laws, and the technology of some
entry gates, require you to press and release the hand
held transmitter button every two seconds during pro-
gramming
Continue to press and hold the Universal Transceiver
button while you press and release the hand held trans-
mitter button until the frequency signal has been learned.
The Universal Transceiver light will flash slowly and
then rapidly when the programming is successful.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Operation
Press and hold the desired button on the Universal
Transceiver until the garage door or other device begins
to operate. The light in the display shows that the signal
is being transmitted. The hand held transmitter may also
be used at any time.
Reprogramming A Single Button
1. Press and hold the Universal Transceiver button to be
reprogrammed. Do not release until step 4 has been
completed.
2. When the indicator light begins to flash slowly (after
20 seconds) position the hand held transmitter one to
three inches away from the button to be trained.
3. Press and hold the hand held transmitter button.
4. The Universal Transceiver indicator light will begin to
flash, first slowly, then rapidly. When the indicator lights
begin to flash rapidly, release both buttons.
Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously trained frequencies, hold
down both outside buttons until the green light begins to
flash.
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
3

1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause undesired
operation.
NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
HomeLinkis a trademark owned by Johnson Controls,
Inc.
ELECTRICAL POWER OUTLET
The power outlet is located in the lower center of your
instrument panel. A second power outlet is located inside
the center console, if so equipped. All accessories con-
nected to any outlet should be removed or turned off
when the vehicle is not in use.
CAUTION!
Electrical Outlet Use With Engine Off
•Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not
in use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will
discharge sufficiently to degrade battery life
and/or prevent engine starting.
•Accessories that draw higher power (i.e., coolers,
vacuum cleaners, lights, etc.) will degrade the
battery even more quickly. Only use these inter-
mittently and with greater caution.
•After the use of high power draw accessories, or
long periods of the vehicle not being started (with
accessories still plugged in), the vehicle must be
driven a sufficient length of time to allow the
alternator to recharge the vehicle’s battery.
•Power outlets are designed for accessory plugs
only. Do not hang any type of accessory or acces-
sory bracket from the plug. Improper use of the
power outlet can cause damage.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS

Instruments And Controls.................87

Instrument Cluster Standard...............88

Instrument Cluster Premium...............89

Instrument Cluster–GTC Model...........90

Instrument Cluster Description.............91

Compass, Temperature, And Trip Computer
Display—If Equipped
...................97
▫Control Buttons.......................97
▫Trip Conditions........................98
▫Compass Temperature Display.............98

Cigar Lighter/Ashtray..................100

Electronic Digital Clock.................100▫To Set The Clock......................101

Radio General Information...............101
▫Radio Broadcast Signals.................101
▫Two Types Of Signals..................101
▫Electrical Disturbances..................101
▫AM Reception.......................101
▫FM Reception........................101

Sales Code RAZ—AM/ FM Stereo Radio
With Cassette Tape Player, CD Player And
CD Changer Controls
...................102
▫Operating Instructions—Radio...........102
▫Power Switch, Volume Control............102
4

▫Seek Button (Radio Mode)...............102
▫Tuning.............................102
▫Radio Data System (RDS)...............102
▫PTY (Program Type) Button..............103
▫Balance............................104
▫Fade..............................104
▫Tone Control........................104
▫AM/FM Selection.....................104
▫Scan Button.........................104
▫To Set The Radio Push-Button Memory......105
▫To Change From Clock To Radio Mode......105
▫Operating Instructions—Tape Player.......105
▫Seek Button.........................105
▫Fast Forward (FF).....................106
▫Rewind (RW)........................106
▫Tape Eject...........................106▫Scan Button.........................106
▫Changing Tape Direction................106
▫Metal Tape Selection...................106
▫Pinch Roller Release...................106
▫Noise Reduction......................106
▫Operating Instructions—CD Player........107
▫Inserting The Compact Disc..............107
▫Seek Button.........................108
▫EJT CD (Eject) Button..................108
▫FF/Tune/RW........................108
▫Program Button 4 (Random Play)..........108
▫Mode..............................108
▫Tape CD Button......................109
▫Time Button.........................109
▫Scan Button.........................109
▫CD Changer Control Capability—
If Equipped.........................109
84 UNDERSTANDING YOUR INSTRUMENT PANEL

Sales Code RBB—AM/FM Stereo Radio
With Cassette Tape Player And
CD Changer Capability
..................110
▫Radio Operation......................110
▫Mode Button........................112
▫Scan Button (Radio Mode)...............112
▫Cassette Player Features................113
▫CD Changer Control Capability—
If Equipped.........................114

Sales Code RBK—AM/ FM Stereo Radio
With CD Player And CD Changer Controls
...115
▫Radio Operation......................115
▫CD Player Operation...................117
▫CD Changer Control Capability—
If Equipped.........................119

Sales Code RB1—AM/FM Stereo Radio With
DVD/GPS Navigation System
............121

6 Disc CD Changer—If Equipped.........121
▫Loading The CD Changer...............122
▫Playing Discs........................122
▫Seek Button.........................122
▫FF/Tune/RW........................122
▫Mode Button........................122
▫Program Button 1.....................123
▫Program Button 4 (Random Play)..........123
▫Program Button 5.....................123
▫Time Button.........................123
▫Changing Modes......................123
▫Removing Discs From The CD Changer.....123
▫CD Changer Operation With
The Changer Off......................124
UNDERSTANDING YOUR INSTRUMENT PANEL 85
4

Remote Sound System Controls—
If Equipped
..........................124
▫Radio Operation......................125
▫Tape Player.........................125
▫CD Player—Single Disc In Radio.........125
▫CD Player—6 Disc CD Changer..........125

Cassette Tape And Player Maintenance......126

Compact Disc Maintenance...............126

Radio Operation And Cellular Phones.......127

Climate Controls......................128
▫Automatic Temperature Control (ATC)—
If Equipped.........................128
▫Manual Air Conditioning/Heater Control—
If Equipped.........................134
86 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 87
4

INSTRUMENT CLUSTER STANDARD
88 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 89
4

INSTRUMENT CLUSTER–GTC MODEL
90 UNDERSTANDING YOUR INSTRUMENT PANEL