trailer CHRYSLER VOYAGER 1996 Service Manual

²Replace spark plugs.
²Replace ignition cables.
²Inspect serpentine drive belt, replace if neces-
sary. This maintenance is not required if belt was
previously replaced.
²Drain and refill automatic transaxle fluid and
replace filter. Adjust band, if so equipped. (See note)
²Change AWD power transfer unit fluid.
78,000 Miles (125 000 km)
²Change engine oil.
²Replace engine oil filter.
81,000 Miles (130 000 km)
²Change engine oil.
²Inspect brake linings.
²Flush and replace engine coolant.
84,000 Miles (134 000 km)
²Change engine oil.
²Replace engine oil filter.
²Change AWD overrunning clutch and rear car-
rier fluid.
87,000 Miles (139 000 km)
²Change engine oil.
90,000 Miles (144 000 km)
²Change engine oil.
²Replace engine oil filter.
²Replace air cleaner element.
²Check PCV valve and replace if necessary.
Not required if previously changed. *
²Inspect serpentine drive belt, replace if neces-
sary. This maintenance is not required if belt was
previously replaced.
²Drain and refill automatic transmission fluid
and replace filter. Adjust bands, if so equipped. (See
note)
²Change AWD power transfer unit fluid.
²Inspect tie rod ends and boot seals.
²Inspect brake linings.
93,000 Miles (149 000 km)
²Change engine oil.
96,000 Miles (154 000 km)
²Change engine oil.
²Replace engine oil filter.
99,000 Miles (158 000 km)
²Change engine oil.
²Inspect brake linings.
102,000 Miles (163 000 km)
²Change engine oil.
²Replace engine oil filter.
105,000 Miles (168 000 km)
²Change engine oil.
²Inspect air cleaner element. Replace as
necessary.
²Inspect serpentine drive belt, replace if neces-
sary. This maintenance is not required if belt was
previously replaced.
²Drain and refill automatic transmission fluid
and filter. Adjust bands, if so equipped. (See note)
²Change AWD power transfer unit fluid.
²Change AWD overrunning clutch and rear car-
rier fluid.
108,000 Miles (173 000 km)
²Change engine oil.
²Replace engine oil filter.
²Inspect brake linings.
111,000 Miles (178 000 km)
²Change engine oil.
²Flush and replace engine coolant.
114,000 Miles (182 000 km)
²Change engine oil.
²Replace engine oil filter.
117,000 Miles (187 000 km)
²Change engine oil.
²Inspect brake linings.
120,000 Miles (192 000 km)
²Change engine oil.
²Replace engine oil filter.
²Replace air cleaner element.
²Inspect PCV valve. Replace as necessary. *
²Inspect serpentine drive belt. Not required if
replaced at 75,000, 90,000 or 105,000 miles.
²Drain and refill automatic transmission fluid
and replace filter. Adjust bands, if so equipped.
²Change AWD power transfer unit fluid.
²Inspect tie rod ends and boot seals.
* This maintenance is recommended by Chrysler to
the owner but is not required to maintain the war-
ranty on the PCV valve.
** If California vehicle, this maintenance is recom-
mended by Chrysler to the owner but is not required
to maintain the warranty of the timing belt.
NOTE: Operating vehicle more than 50% in heavy
traffic during hot weather, above 90ÉF (32ÉC), using
vehicle for police, taxi, limousine type operation or
trailer towing require the more frequent transaxle
service noted in Schedule ± B. Perform these ser-
vices if vehicle is usually operated under these con-
ditions.
Inspection and service should also be performed
anytime a malfunction is observed or suspected.
0 - 6 LUBRICATION AND MAINTENANCENS
GENERAL INFORMATION (Continued)

MAINTENANCE SCHEDULES
INDEX
page page
GENERAL INFORMATION
MAINTENANCE SCHEDULE............... 2
MAINTENANCE SCHEDULEÐ
DIESEL ENGINE....................... 2SCHEDULEÐA (DIESEL).................. 2
SCHEDULEÐB (DIESEL).................. 3
UNSCHEDULED INSPECTION.............. 2
GENERAL INFORMATION
MAINTENANCE SCHEDULE
Refer to the 1998 GS Service Manual for Gasoline
Engine and non-engine related Maintenance Sched-
ules.
MAINTENANCE SCHEDULEÐDIESEL ENGINE
The following are engine related Maintenance
items which are unique to Diesel engine-equipped
vehicles. Refer to the 1998 GS Service Manual for
Gasoline Engine and non-engine related Maintenance
Schedules.
The service intervals are based on odometer read-
ings in kilometers. There are two maintenance sched-
ules that show proper service intervals. Use the
schedule that best describes the conditions the vehi-
cle is operated under.Schedule-Alists all the sched-
uled maintenance to be performed under normal
operating conditions.Schedule-Bis the schedule for
vehicles that are operated under one or more of the
following conditions:
²Day and night temperatures are below freezing.
²Stop and go driving.
²Long periods of engine idling.
²Driving in dusty conditions.
²Short trips of less than 5 miles.
²Operation at sustained high speeds during hot
weather above 32ÉC (90ÉF).
²Taxi, police or delivery service.
²Trailer towing.
UNSCHEDULED INSPECTION
At Each Stop for Fuel
²Check engine oil level, add as required.
²Check windshield washer solvent and add if
required.
Once a Month
²Check tire pressure and look for unusual wear
or damage.
²Inspect battery and clean and tighten terminals
as required.²Check fluid levels of coolant reservoir, brake
master cylinder, power steering and transaxle and
add as needed.
²Check all lights and all other electrical items for
correct operation.
²Check rubber seals on each side of the radiator
for proper fit.
At Each Oil Change
²Inspect exhaust system.
²Inspect brake hoses
²Inspect the CV joints and front suspension com-
ponents
²Rotate the tires at each oil change interval
shown on ScheduleÐA (7,500 miles) or every other
interval shown on ScheduleÐ B (6,000 miles).
²Check the coolant level, hoses, and clamps.
²If your mileage is less than 7,500 miles (12 000
km) yearly, replace the engine oil filter at each oil
change.
²Replace engine oil filter.
SCHEDULEÐA (DIESEL)
1 000 KM
²Change engine oil.
²Change engine oil filter.
²Check all fluid levels.
²Check correct torque, intake manifold mounting
nuts.
²Check correct torque, exhaust manifold mount-
ing nuts.
²Check correct torque, turbocharger mounting
nuts.
²Check correct torque, water manifold bolts.
10 000 KM
²Change engine oil.
²Change engine oil filter.
20 000 KM
²Change engine oil.
²Change engine oil filter.
²Replace air filter element.
0 - 2 LUBRICATION AND MAINTENANCENS/GS

Before test driving a brake complaint vehicle, note
whether the Red or Amber Brake Warning Lamp is
turned on. If it is the Red Brake Warning Lamp,
refer to the hydraulic system section in the brake
group of this manual. If the ABS Warning lamp
was/is on, test drive the vehicle as described below, to
verify the complaint. While the ABS Warning Lamp
is on, the ABS is not functional. The standard brake
system and the ability to stop the car may not be
affected if only the ABS Warning Lamp is on.
Discuss with the owner of the vehicle or note any
other electrical problems or conditions that may be
occurring on the vehicle. They may have an effect on
the antilock brake system's function.
(1) Turn the key to the off position and then back
to the on position. Note whether the ABS Warning
Lamp continues to stay on. If it does, refer to the
diagnostic manual covering the ITT Teves Mark 20
ABS system for the required test procedures.
(2) If the ABS Warning Lamp goes out, shift into
gear and drive the car to a speed of 20 kph (12 mph)
to complete the ABS start up cycle. If at this time the
ABS Warning Lamp goes on refer to the ITT Teves
Mark 20 Diagnostic Manual.
(3) If the ABS Warning Lamp remains OUT, drive
the vehicle a short distance. During this test drive be
sure that the vehicle achieves at least 40 mph. Brake
to at least one complete stop in an ABS cycle, and
again accelerate to 25 mph.
(4) If a functional problem with the ABS system is
determined while test driving a vehicle, refer to the
diagnostic manual covering the ITT Teves Mark 20
ABS system for the required test procedures and
proper use of the DRB diagnostic scan tool.
ABS SERVICE PRECAUTIONS
The ABS uses an electronic control module, the
CAB. This module is designed to withstand normal
current draws associated with vehicle operation.
Care must be taken to avoid overloading the CAB
circuits.In testing for open or short circuits, do
not ground or apply voltage to any of the cir-
cuits unless instructed to do so for a diagnostic
procedure.These circuits should only be tested
using a high impedance multi-meter or the DRB
tester as described in this section. Power should
never be removed or applied to any control module
with the ignition in the ON position. Before removing
or connecting battery cables, fuses, or connectors,
always turn the ignition to the OFF position.
CAUTION: Use only factory wiring harnesses. Do
not cut or splice wiring to the brake circuits. The
addition of after-market electrical equipment (car
phone, radar detector, citizen band radio, trailer
lighting, trailer brakes, ect.) on a vehicle equippedwith antilock brakes may affect the function of the
antilock brake system.
SERVICE PROCEDURES
BRAKE FLUID LEVEL INSPECTION
CAUTION: Use only Mopar brake fluid or an equiv-
alent from a tightly sealed container. Brake fluid
must conform to DOT 3 specifications. Do not use
petroleum-based fluid because seal damage in the
brake system will result.
For the specific procedure covering the inspection
of the brake fluid level and adding brake fluid to the
reservoir, refer to the Service Adjustments Section in
this group of the service manual.
BLEEDING TEVES MARK 20 HYDRAULIC SYSTEM
The base brake system must be bled anytime air is
permitted to enter the hydraulic system, due to dis-
connection of brake lines, hoses or components. The
ABS system, particularly the HCU, should only be
bled when the HCU is replaced or removed from the
vehicle, or if there is reason to believe the HCU has
ingested air. Under most circumstances that would
require brake bleeding, only the base brake system
needs to be bled.
It is important to note that excessive air in the
brake system will cause a soft or spongy feeling
brake pedal.
During bleeding operations, be sure that the brake
fluid level remains close to the FULL level in the res-
ervoir. Check the fluid level periodically during the
bleeding procedure and add DOT 3 brake fluid as
required.
The Teves Mark 20 ABS hydraulic system and the
base brake hydraulic system must be bled as two
independent braking systems. The non ABS portion
of the brake system is to be bled the same as any
non ABS system. Refer to the Service Adjustments
section in this manual for the proper bleeding proce-
dure to be used. This brake system can be either
pressure bled or manually bled.
The ABS portion of the brake system MUST be
bled separately. This bleeding procedure requires the
use of the DRB Diagnostic Tester and the bleeding
sequence procedure outlined below.
ABS BLEEDING PROCEDURE
When bleeding the ABS system, the following
bleeding sequenceMUSTbe followed to insure com-
plete and adequate bleeding. The ABS system can be
bled using a manual bleeding procedure or standard
pressure bleeding equipment.
NSBRAKES 5 - 99
DIAGNOSIS AND TESTING (Continued)

ties to keep the engine satisfactorily cooled (Fig. 5),
(Fig. 6), (Fig. 7) and (Fig. 8).
CAUTION: Plastic tanks, while stronger then brass
are subject to damage by impact, such as wrenches
etc., or by excessive torque on hose clamps.
If the plastic tank is damaged, replace the radia-
tor.
RADIATOR PRESSURE CAP
The radiator is equipped with a pressure cap that
releases excessive cooling system pressure; maintain-
ing a range of 97-124 kPa (14-18 psi).
The cooling system will operate at higher than
atmospheric pressure. The higher pressure raises thecoolant boiling point thus, allowing increased radia-
tor cooling capacity.
There is also a vent valve in the center of the cap.
This valve also opens when coolant is cooling and
contracting allowing coolant to return to radiator
from coolant reserve system tank by vacuum through
connecting hose.If valve is stuck shut, or the
coolant recovery hose is pinched, the radiator
hoses will be collapsed on cool down. Clean the
vent valve (Fig. 9) and inspect coolant recovery
hose routing, to ensure proper sealing when
boiling point is reached.
The gasket in the cap seals the filler neck, so that
vacuum can be maintained, allowing coolant to be
drawn back into the radiator from the reserve tank.
Fig. 5 Cooling ModuleÐ2.4L
Fig. 6 Cooling ModuleÐTrailer Tow (With Rear A/C)
7 - 4 COOLING SYSTEMNS
GENERAL INFORMATION (Continued)

and the remove the splash shield to gain access to
the drive belts.
BELT TENSION GAUGE METHOD
Use belt tensioning Special Tool Kit C-4162 for:
CAUTION: The Burroughs gauge for the Poly-V
belt is not to be used on the V-belt. These gauges
are not interchangeable.
²For conventional V-belts affix the Burroughs
gauge (Special Tool C-4162) to the belt. Adjust the
belt tension for New or Used belt as prescribed in the
Belt Tension Chart.
²For a Poly-V belt affix the Poly-V Burroughs
gauge to the belt and then apply specified tension to
the belt as prescribed in the Belt Tension Chart
Adjust belt tension for aNeworUsedbelt as pre-
scribed in the Belt Tension Chart.
BELT TENSION CHARTSPECIFICATIONS
COOLING SYSTEM CAPACITY
TORQUE CHART
DESCRIPTION TORQUE
Thermostat Housing
BoltsÐ2.4L & 3.3/3.8L......28N´m(250 in. lbs.)
BoltsÐ3.0L...............12N´m(105 in. lbs.)
Water Pump Mounting
BoltsÐ2.4L & 3.3/3.8L......12N´m(250 in. lbs.)
BoltsÐ3.0L...............27N´m(240 in. lbs.)
Water Pump Inlet Tube
BoltsÐ2.4L...............12N´m(250 in. lbs.)
BoltsÐ3.0L................11N´m(94in.lbs.)
Water Pump Pulley
BoltsÐ3.3/3.8L............28N´m(250 in. lbs.)
Transaxle Oil Cooler Hose
ClampsÐAll Engines.........2N´m(18in.lbs.)
Radiator Mounting Upper Bracket
NutÐAll Engines..........12N´m(105 in. lbs.)
SPECIAL TOOLS
COOLING
ACCESSORY DRIVE
BELTGAUGE
2.4L ENGINE
A/C COMPRESSOR /
GENERATORNEW 190 LB.
USED 115 LB.
POWER STEERING NEW 140 LB.
USED 90 LB.
3.0L ENGINE
A/C COMPRESSOR NEW 150 LB.
USED 80 LB.
GENERATOR / POWER
STEERINGDYNAMIC TENSIONER
3.3/3.8L ENGINES
A/C COMPRESSOR DYNAMIC TENSIONER
GENERATOR / WATER
PUMP / POWER
STEERINGDYNAMIC TENSIONER
Engine Standard Duty Trailer Tow or
Heavy Duty
Front
HeaterRear
HeaterFront
HeaterRear
Heater
2.4L 10.6
liters*
(11.23
qts.)*N/A N/A N/A
3.0L 12.3
liters*
(13.0
qts.)*N/A N/A 15.0
liters*
(15.9
qts.)*
3.3/3.8L 12.5
liters*15.26
liters*12.5
liters*15.26
liters*
(13.23
qts.)*(16.13
qts.)*(13.23
qts.)*(16.13
qts)*
*Includes Heater and Coolant Recovery Tank Filled to
Max Level.
Belt Tension Gauge C-4162
7 - 26 COOLING SYSTEMNS
ADJUSTMENTS (Continued)

WIRING DIAGRAMS
CONTENTS
page page
AIR CONDITIONING-HEATER.......... 8W-42-1
AIRBAG SYSTEM................... 8W-43-1
ANTI-LOCK BRAKES................. 8W-35-1
AUDIO SYSTEM.................... 8W-47-1
BODY CONTROL MODULE............ 8W-45-1
CHARGING SYSTEM................. 8W-20-1
COMPONENT INDEX................. 8W-02-1
CONNECTOR/GROUND LOCATIONS..... 8W-90-1
CONNECTOR PIN-OUTS.............. 8W-80-1
FRONT LIGHTING................... 8W-50-1
FUEL/IGNITION SYSTEM............. 8W-30-1
GENERAL INFORMATION............. 8W-01-1
GROUND DISTRIBUTION............. 8W-15-1
HORN/CIGAR LIGHTER/POWER OUTLET . 8W-41-1
INSTRUMENT CLUSTER.............. 8W-40-1
INTERIOR LIGHTING................. 8W-44-1
JUNCTION BLOCK................... 8W-12-1
MESSAGE CENTER.................. 8W-46-1OVERHEAD CONSOLE................ 8W-49-1
POWER DISTRIBUTION.............. 8W-10-1
POWER DOOR LOCKS............... 8W-61-1
POWER MIRRORS.................. 8W-62-1
POWER SEAT...................... 8W-63-1
POWER WINDOWS.................. 8W-60-1
REAR LIGHTING.................... 8W-51-1
SPLICE INFORMATION............... 8W-70-1
SPLICE LOCATIONS................. 8W-95-1
STARTING SYSTEM................. 8W-21-1
TRAILER TOW...................... 8W-54-1
TRANSMISSION CONTROL SYSTEM.... 8W-31-1
TURN SIGNALS..................... 8W-52-1
VEHICLE SPEED CONTROL........... 8W-33-1
VEHICLE THEFT SECURITY SYSTEM.... 8W-39-1
WINDOW DEFOGGERS............... 8W-48-1
WIPERS........................... 8W-53-1
NS/GSWIRING DIAGRAMS 8W - 1

SECTION IDENTIFICATION
The wiring diagrams are grouped into individual
sections. If a component is most likely found in a par-
ticular group, it will be shown complete (all wires,
connectors, and pins) within that group. For exam-
ple, the Auto Shutdown Relay is most likely to be
found in Group 30, so it is shown there complete. It
can, however, be shown partially in another group if
it contains some associated wiring.
SYMBOLS
International symbols are used throughout the wir-
ing diagrams. These symbols are consistent with
those being used around the world.
GROUP TOPIC
8W-01 thru 8W-09 General Information and
Diagram Overview
8W-10 thru 8W-19 Main Sources of Power and
Vehicle Grounding
8W-20 thru 8W-29 Starting and Charging
8W-30 thru 8W-39 Powertrain/Drivetrain
Systems
8W-40 thru 8W-49 Body Electrical items and A/C
8W-50 thru 8W-59 Exterior Lighting, Wipers, and
Trailer Tow
8W-60 thru 8W-69 Power Accessories
8W-70 Splice Information
8W-80 Connector Pin Outs
8W-90 Connector Locations
(including grounds)
8W-95 Splice Locations
NS/GS8W-01 GENERAL INFORMATION 8W - 01 - 5
DESCRIPTION AND OPERATION (Continued)

Component Page
Seat Belt Indicator Lamp.................8W-40
Seat Belt Switch........................8W-40
Sentry Key Immobilizer Module............8W-39
Service Engine Soon Lamp.............8W-30, 46
Sliding Door Contacts....................8W-61
Sliding Door Lock Motors.................8W-61
Speed Control Switches...............8W-30, 33
Speedometer...........................8W-40
Stop Lamp Switch...................8W-33, 51
Stop/Turn Signal Relays..................8W-54
Tachometer............................8W-40
Tail/Stop Lamp.........................8W-51
Tail/Turn Signal Lamp................8W-51, 52
Throttle Position Sensor..................8W-30
Traction Control Switch..................8W-35
Trailer Tow Connector...................8W-54
Transmission Control Module..............8W-31
Transmission Control Relay............8W-10, 31
Transmission Control Solenoids............8W-31
Transmission Range Sensor...............8W-31
Trip Odometer.........................8W-40Component Page
Turbine Speed Sensor....................8W-31
Turbo Boost Pressure Sensor..............8W-30
Turn Indicators......................8W-46, 52
Turn Signal/Hazard Switch............8W-46, 52
Underdrive Solenoid.....................8W-31
Universal Garage Door Opener............8W-49
Vacuum Solenoid.......................8W-33
Vehicle Speed Control Servo...............8W-33
Vehicle Speed Sensor....................8W-30
Vent Motors...........................8W-60
Vent Solenoids.........................8W-33
Visor/Vanity Mirror Lamps................8W-44
Voltage Regulator.......................8W-20
Volts Indicator Lamp....................8W-40
VTSS Lamp........................8W-39, 46
Washer Module.........................8W-53
Wheel Speed Sensors....................8W-35
Wiper High/Low Relay...................8W-53
Wiper Module..........................8W-53
Wiper On Relay........................8W-53
NS/GS8W - 02 COMPONENT INDEX 8W - 02 - 3

8W-12 JUNCTION BLOCK
Component PageA/C Compressor Clutch Relay..............8W-12-13
A/C Heater Control.................8W-12-9, 12, 23
Airbag Control Module...................8W-12-13
Ash Receiver Lamp...................8W-12-19, 23
Automatic Day/Night Mirror................8W-12-9
Back-Up Switch........................8W-12-12
Body Control Module........8W-12-8, 9, 14, 15, 17, 18,
19, 20, 22, 23, 24, 26
Brake Pressure Switch...................8W-12-17
Cigar/Accessory Relay....................8W-12-16
Clutch Interlock Switch..................8W-12-16
Clutch Interlock Switch Jumper............8W-12-16
Combination Flasher/DRL Module . . .8W-12-12, 17, 18, 19
Controller Anti-Lock Brake................8W-12-12
Courtesy Lamp Relay....................8W-12-22
CS01...............................8W-12-22
CS02...............................8W-12-21
CS04................................8W-12-9
CS1................................8W-12-22
Data Link Connector....................8W-12-20
Door Lock Relay.....................8W-12-15, 19
Door Unlock Relay...................8W-12-14, 19
Driver Door Courtesy Lamp...............8W-12-22
Driver Door Lock Motor................8W-12-14, 15
Driver Door Lock Switch..................8W-12-23
Driver Door Unlock Relay..............8W-12-14, 19
Driver Heated Seat Switch................8W-12-12
Driver Power Mirror..................8W-12-10, 26
Driver Power Window Switch............8W-12-16, 23
EGR Solenoid.........................8W-12-13
Electric Wiper De-Icer...................8W-12-11
Engine Starter Motor Relay...............8W-12-16
ES07...............................8W-12-13
ES29...............................8W-12-13
Evap Leak Detection Pump................8W-12-13
Fog Lamp Relay.......................8W-12-25
Front Blower Motor Relay.................8W-12-12
Front Cigar Lighter/Power Outlet...........8W-12-23
Front Reading Lamps/Switch..............8W-12-21
Front Washer Motor................8W-12-16, 23, 24
Front Wiper Switch................8W-12-16, 23, 24
Fuel Heater Relay......................8W-12-13
Fuel Pump Relay.......................8W-12-13
Fuse 1 (JB)............................8W-12-8
Fuse 2 (JB).........................8W-12-9, 20
Fuse 2 (PDC)..........................8W-12-13
Fuse 3 (JB)............................8W-12-8
Fuse 4 (JB)............................8W-12-8
Fuse 5 (JB).........................8W-12-8, 24
Fuse 6 (JB)............................8W-12-9
Fuse 6 (PDC)..........................8W-12-25
Fuse 7 (JB)...........................8W-12-10
Fuse 8 (JB)...........................8W-12-11
Fuse 9 (JB)...........................8W-12-11
Fuse 10 (JB)..........................8W-12-16
Fuse 11 (JB)..........................8W-12-11
Fuse 12 (JB)..........................8W-12-12
Fuse 18 (PDC).........................8W-12-26
Fuse 22 (PDC).......................8W-12-8, 24
G300..........................8W-12-11, 19, 26
Glove Box Lamp.......................8W-12-21
Headlamp Dimmer Switch..............8W-12-18, 25
Headlamp Switch.............8W-12-8, 19, 22, 23, 25
Headlamp Washer......................8W-12-24
Horn Relay...........................8W-12-17
HS2................................8W-12-12
HS4................................8W-12-12Component PageIgnition Switch...................8W-12-17, 19, 20
Instrument Cluster..............8W-12-9, 19, 20, 23
Junction Block......8W-12-2, 8, 9, 10, 11, 12, 13, 14, 15,
16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26
Key-In Halo Lamp.................8W-12-19, 22, 26
Left Combination Relay..................8W-12-18
Left Fog Lamp.......................8W-12-8, 25
Left Front Park/Turn Signal Lamp.........8W-12-8, 18
Left Liftgate Flood Lamp.................8W-12-22
Left Low Headlamp.....................8W-12-25
Left Rear Lamp Assembly...............8W-12-8, 18
Left Rear Sliding Door Contact...........8W-12-14, 15
Left Repeater Lamp.....................8W-12-18
Left Stop/Turn Signal Relay...............8W-12-18
License Lamp..........................8W-12-8
Liftgate Lock Motor..................8W-12-14, 15
Low Beam Relay.......................8W-12-25
Message Center..............8W-12-9, 17, 18, 19, 20
Name Brand Speaker Relay.............8W-12-11, 19
Overhead Console.......................8W-12-9
Park Brake Switch......................8W-12-17
Park Lamp Relay.....................8W-12-8, 24
Passenger Door Courtesy Lamp.............8W-12-22
Passenger Door Lock Motor.............8W-12-14, 15
Passenger Door Lock Switch...............8W-12-23
Passenger Heated Seat Switch..............8W-12-12
Passenger Power Mirror...............8W-12-10, 26
Passenger Power Window Switch.........8W-12-16, 23
Power Distribution Center.........8W-8,12-12, 13, 16,
17, 24, 25, 26
Power Folding Mirror Switch............8W-12-19, 26
Power Mirror Fold Relay..................8W-12-26
Power Mirror Switch...............8W-12-19, 21, 23
Power Mirror Unfold Relay................8W-12-26
Powertrain Control Module................8W-12-13
PTC 1 (JB)...........................8W-12-13
PTC 3 (JB)......................8W-12-14, 15, 24
PTC 7 (JB).........................8W-12-16, 24
PTC 8 (JB)...........................8W-12-16
PTC 9 (JB)...........................8W-12-16
Radio..........................8W-12-11, 20, 23
Radio Choke..........................8W-12-11
Rear A/C Heater Unit....................8W-12-11
Rear Blower Front Control Switch...........8W-12-23
Rear Blower Rear Control Switch...........8W-12-23
Rear Washer Motor.....................8W-12-16
Rear Window Defogger...................8W-12-10
Rear Window Defogger Relay............8W-12-10, 12
Rear Wiper Motor.......................8W-12-9
Remote Keyless Entry Module..............8W-12-20
Right Combination Relay.................8W-12-18
Right Fog Lamp......................8W-12-8, 25
Right Front Park/Turn Signal Lamp........8W-12-8, 18
Right Liftgate Flood Lamp................8W-12-22
Right Rear Lamp Assembly..............8W-12-8, 18
Right Rear Sliding Door Contact..........8W-12-14, 15
Right Repeater Lamp....................8W-12-18
Right Stop/Turn Signal Relay..............8W-12-18
Sentry Key Immobilizer Module..........8W-12-13, 21
Stop Lamp Switch......................8W-12-19
Traction Control Switch................8W-12-19, 23
Trailer Tow Connector....................8W-12-8
Transmission Control Module.............8W-12-9, 16
Transmission Range Sensor................8W-12-12
Turn Signal/Hazard Switch................8W-12-17
Universal Garage Door Opener.............8W-12-23
Washer Module.................8W-12-8, 15, 16, 23
NS/GS8W - 12 JUNCTION BLOCK 8W - 12 - 1

BATT A0
40A
FUSE
22
CENTER DISTRIBUTION
POWER
10C3
8587
3086
RELAY
LAMP
PARK
C14
BLOCK
JUNCTION
C292C1
163FUSE
15A
L7
12
BK/YL
BODY
CONTROL
MODULE
L97
18
PK/DB
15A
FUSE
5
1
10A
FUSE
1
C123 5C118C1
L78
20
DG/YL
L78
20
DG/YL
2
TURN PARK/
FRONT
RIGHT
RIGHT
REAR
LAMP
ASSEMBLY
4LEFT
FRONT
PARK/
TURN
LAMP
2
BR/YL20 L77L77
20
BR/LB
L77
20
BR/LB
4
ASSEMBLY LAMP
REAR
LEFT2
LAMP
LICENSE
L77
20
BR/LB
LJ01 B175
L15
J02A6
T05
B994T08
B984
L78
20
DG/YL
TRAILER
TOW OTHERS
2TRAILER
TOW
CONNECTOR
L78
18
BR
L77
20
BR/LB
L77
20
BR/LB
OTHERSTOW TRAILER
SIGNAL
SIGNAL
LAMP
WASHER
MODULE
(BUILT-UP
-EXPORT)
C25
-EXPORT) (BUILT-UP
SWITCH
HEADLAMP
28
B23
P18B28L77
18
BR/YL
*1
*3*1*3 4FUSE
15A
C13
1
1
-EXPORT)
(BUILT-UP
LAMP
FOG
LEFT
RIGHT
FOG
LAMP
(BUILT-UP
-EXPORT)F39
18
PK/LG
F39
18
PK/LG
* BUILT-UP-EXPORT
56 (8W-10-8)
(8W-10-8)
(8W-12-2)
(8W-45-3) (8W-10-17)
(8W-51-4)
(8W-51-5)
(8W-51-6)(8W-50-11)
(8W-50-12)(8W-51-4)
(8W-51-5)
(8W-51-6)
(8W-51-2) (8W-54-2)
(8W-50-11)
(8W-50-12)(8W-53-5)
(8W-50-10)(8W-50-7)
(8W-50-7)
8W - 12 - 8 8W-12 JUNCTION BLOCKNS/GS
J988W-3GS001208