sensor CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
* CHECKING THE FUEL SYSTEM
POSSIBLE CAUSES
FUEL PUMP GROUND CIRCUIT OPEN
FUEL PUMP GROUND CIRCUIT OPEN
FUEL PUMP RELAY FUSED B(+) CIRCUIT OPEN
FUEL PUMP RELAY FUSED B(+) CIRCUIT OPEN
FUEL PUMP RELAY OUTPUT CIRCUIT OPEN
FUEL PUMP RELAY OUTPUT CIRCUIT OPEN
FUEL FILTER DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL PUMP DEFECTIVE
FUEL PUMP DEFECTIVE
FUEL PUMP RELAY
FUEL PUMP RELAY
IN-TANK FUEL PRESSURE REGULATOR DEFECTIVE
IN-TANK FUEL PRESSURE REGULATOR DEFECTIVE
THROTTLE POSITION SENSOR DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL FILTER DEFECTIVE
FUEL INLET STRAINER DEFECTIVE
FUEL INLET STRAINER DEFECTIVE
FUEL PUMP MODULE DEFECTIVE
FUEL PUMP MODULE DEFECTIVE
FUEL SUPPLY LINE DEFECTIVE
FUEL SUPPLY LINE DEFECTIVE
FUEL TUBE RESTRICTED
FUEL TUBE RESTRICTED
POWERTRAIN CONTROL MODULE DEFECTIVE
POWERTRAIN CONTROL MODULE DEFECTIVE
THROTTLE CABLES DEFECTIVE
THROTTLE CABLES DEFECTIVE
THROTTLE POSITION SENSOR DEFECTIVE
278
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
1Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Ensure the Throttle Cables are not holding the Throttle open.
Is the Throttle held open?ENGINE - 3.0L V6
Ye s®Repair condition that holds the Throttle Body open.
Perform Powertrain Verification Test VER-1A.
No®Go To 2
2 Ignition On, Engine Not Running
With the DRB, actuate the Fuel System and check for Fuel Pump operation at the
Fuel Tank.
Is the Fuel Pump operating?ENGINE - 3.0L V6
Ye s®Go To 3
No®Go To 13
3 Ignition On, Engine Not Running
With DRB, read Throttle Position Sensor voltage.
Is the voltage above 1.5 volts?ENGINE - 3.0L V6
Ye s®Disconnect the TP Sensor Conn. Replace Throttle Position Sensor.
Perform Powertrain Verification Test VER-1A.
No®Go To 4
4 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Relieve Fuel pressure.
Install a Fuel Pressure Gauge to the Fuel Rail.
Note: The Fuel Tank must be at least 1/4 full for the following tests.
Ignition On, Engine Not Running.
With the DRB, actuate the Fuel System.
Read the Fuel Pressure Gauge.
Fuel pressure should be 43 to 53 psi for Gasoline.
Is the Fuel pressure above the specification ?ENGINE - 3.0L V6
Ye s®Go To 5
No®Go To 8
5 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Filter for a restriction.
Is there a restriction?ENGINE - 3.0L V6
Ye s®Replace the Fuel Filter.
Perform Powertrain Verification Test VER-1A.
No®Go To 6
279
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
10 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pump Module.
Inspect the Fuel Pump Inlet Strainer.
Is the Inlet Strainer plugged?ENGINE - 3.0L V6
Ye s®Replace the Fuel Inlet Strainer.
Perform Powertrain Verification Test VER-1A.
No®Go To 11
11 Record the Fuel Pressure Gauge reading.
Ignition key off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Remove Fuel Pressure Gauge Adapter 6433 and reconnect Fuel Line to Fuel Rail.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 3.0L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 12
12 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 3.0L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
13 Ignition On, Engine Not Running
With DRB, read Throttle Position Sensor voltage.
Is the voltage above 1.5 volts?ENGINE - 3.0L V6
Ye s®Disconnect the TP Sensor Conn. Replace Throttle Position Sensor.
Perform Powertrain Verification Test VER-1A.
No®Go To 14
14 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 3.0L V6
Ye s®Go To 15
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
281
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Check Transmission Fluid level and ensure it is clear of any debris.
Is the Transmission Fluid okay?TRANSMISSION -
AUTOMATIC
3-SPD, 31TH
Ye s®Go To 4
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Disconnect the TCC Solenoid connector.
Note: Check connectors - Clean/repair as necessary.
Turn key on.
Use a Voltmeter in the following step.
Using a Voltmeter, measure the Fused Ignition Switch Output Circuit at Solenoid
Connector.
Is the voltage above 10.0 volts?TRANSMISSION -
AUTOMATIC
3-SPD, 31TH
Ye s®Go To 5
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off
Disconnect the TCC Solenoid connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure across the Solenoid for resistance.
Was resistance between 30.0 and 50.0 ohms?TRANSMISSION -
AUTOMATIC
3-SPD, 31TH
Ye s®Go To 6
No®Replace TCC Solenoid.
Perform Powertrain Verification Test VER-5A.
6 Drive Vehicle
Maintain 50 MPH per DRB. Wait 10 seconds in lockup. Record Engine RPM.
Was engine RPM 2200 +/- 50 RPM?TRANSMISSION -
AUTOMATIC
3-SPD, 31TH
Ye s®Go To 7
No®Inspect Differential, Output Shaft, or Gear Box. Refer to service
instructions for proper diagnosis.
Perform Powertrain Verification Test VER-5A.
7 Ignition Off
Remove VSS.
Note: Check connectors - Clean/repair as necessary.
Inspect sensor and gear for damage, also improper wheel size.
Were any problems found?TRANSMISSION -
AUTOMATIC
3-SPD, 31TH
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
303
TRANSMISSION
P-0740 TORQUE CONV CLUTCH, NO RPM DROP AT LOCKUP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 Ignition Off.
Inspect the Wiring and Connector relating to Park/Neutral Position Switch.
Were any problems found?TRANSMISSION -
AUTOMATIC
4-SPD, 41TE
and/or TRANSMIS-
SION - AUTO-
STICK
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
9 Ignition Off.
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure between the Park/Neutral Switch Sense Circuit at the
PCM Connector and Ground.
While moving Gear Selector between Park and Reverse, watch Ohmmeter display.
Did the display switch from below 5.0 ohms to above 5.0 ohms?TRANSMISSION -
AUTOMATIC
4-SPD, 41TE
and/or TRANSMIS-
SION - AUTO-
STICK
Ye s®Replace the PCM.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
10 Ignition Off.
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure between the Park/Neutral Switch Sense Circuit at the
PCM Connector and Ground.
While moving gear selector between Park and Reverse, watch Ohmmeter display.
Did the display stay below 5.0 ohms at all times?TRANSMISSION -
AUTOMATIC
4-SPD, 41TE
and/or TRANSMIS-
SION - AUTO-
STICK
Ye s®Repair the P/N Switch Sense Circuit for a short to Ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 11
11 Ignition Off.
Disconnect the PCM.
Disconnect the Transmission Range Sensor (TRS) Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Park/Neutral Switch Sense Circuit from the PCM
to the TRS.
Is the resistance below 5.0 ohms?TRANSMISSION -
AUTOMATIC
4-SPD, 41TE
and/or TRANSMIS-
SION - AUTO-
STICK
Ye s®Go To 12
No®Repair open Park/Neutral Switch Sense Circuit.
Perform Powertrain Verification Test VER-5A.
12 If there are no potential causes remaining, the Transmission Range Sensor is
assumed to be defective.
View repair options.TRANSMISSION -
AUTOMATIC
4-SPD, 41TE
and/or TRANSMIS-
SION - AUTO-
STICK
Repair
Replace the TRS.
Perform Powertrain Verification Test VER-5A.
309
TRANSMISSION
P-1899 PARK/NEUTRAL SWITCH STUCK IN PARK OR IN GEAR Ð
Continued
ProCarManuals.com

8.3 DATA LINK CONNECTOR
8.4 SENSORS
2.0L AND 2.4L
2.0L AND 2.4L3.3L AND 3.8L
C
O
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
327
COMPONENT LOCATIONS
ProCarManuals.com

2.0L AND 2.4L3.3L AND 3.8L
2.0L AND 2.4L2.0L AND 2.4L
3.0L3.0L
C
O
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
328
COMPONENT LOCATIONS
8.4 SENSORS (Continued)
ProCarManuals.com

3.0L 1/13.3L AND 3.8L 1/1
3.0L, 3.3L, AND 3.8L 1/2
8.5 FUEL SYSTEM
2.0L AND 2.4L3.0L
C
O
M
P
O
N
E
N
T
L
O
C
A
T
I
O
N
S
330
COMPONENT LOCATIONS
8.4 SENSORS (Continued)
ProCarManuals.com

9.0 CONNECTOR PINOUTS
A/C COMPRESSOR CLUTCH - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 C3 18DB/BK A/C CLUTCH COMPRESSOR RELAY OUTPUT
2 Z1 18BK GROUND
AMBIENT TEMPERATURE SENSOR - GRAY 2 WAYCAV CIRCUIT FUNCTION
1 G31 20VT/LG AMBIENT TEMPERATURE SENSOR SIGNAL
2 G32 20BK/LB SENSOR GROUND
AMBIENT TEMPERATURE SENSOR (SENSOR SIDE) 2 WAYCAV CIRCUIT FUNCTION
1 - AMBIENT TEMPERATURE SENSOR SIGNAL
2 - SENSOR GROUND
BRAKE LAMP SWITCH - GRAY 6 WAYCAV CIRCUIT FUNCTION
1 K29 20WT/PK BRAKE SWITCH SENSE
2 Z1 20BK GROUND
3 V32 20YL/RD SPEED CONTROL ON/OFF SWITCH SENSE
4 V30 20DB/RD SPEED CONTROL BRAKE SWITCH OUTPUT
5 L50 18WT/TN BRAKE LAMP SWITCH OUTPUT
6 F32 18PK/DB FUSED B(+)
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
333
CONNECTOR PINOUTS
ProCarManuals.com

BRAKE SHIFT INTERLOCK SOLENOID (EXCEPT BUILT-UP EXPORT)-2WAYCAV CIRCUIT FUNCTION
1 K29 20WT/PK RED BRAKE WARNING LAMP DRIVER
2 F11 20RD/WT FUSED IGNITION SWITCH OUTPUT (ST-RUN-OFF)
CAMSHAFT POSITION SENSOR - BLACK 3-WAYCAV CIRCUIT FUNCTION
1 K7 18OR 8V SUPPLY
2 K4 18BK/LB SENSOR GROUND
3 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
CLOCKSPRING C1 - YELLOW 2 WAYCAV CIRCUIT FUNCTION
1 R43 18BK/LB DRIVER AIRBAG LINE 1
2 R45 18DG/LB DRIVER AIRBAG LINE 2
CLOCKSPRING C2 - NATURAL 5 WAYCAV CIRCUIT FUNCTION
1 X3 20BK/RD HORN RELAY CONTROL SENSE
2 X10 20RD/WT (RADIO RE-
MOTE CONTROL)RADIO MUX
3 Z2 20BK/LG (SPEED CON-
TROL)GROUND
4 V37 20RD/LG (SPEED
CONTROLSPEED CONTROL SWITCH SIGNAL
5 X20 20RD/BK (RADIO RE-
MOTE CONTROL)RADIO CONTROL MUX
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
334
CONNECTOR PINOUTS
ProCarManuals.com