brake CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
P-0500 NO VEHICLE SPEED SENSOR SIGNAL
When Monitored and Set Condition:
P-0500 NO VEHICLE SPEED SENSOR SIGNAL
When Monitored: For 3 Speed: With engine running, transmission not in park or neutral,
brakes not applied, engine rpm greater than 1500. For 4 Speed: With the engine running,
transmission not in park or neutral, brakes not applied, engine rpm greater than 1500.
Set Condition: For 3 Speed: No signal from the vehicle speed sensor for more than 11
seconds for 2 consecutive trips. For 4 Speed: No signal from the vehicle speed sensor (TCM)
is present for more than 11 seconds for 2 consecutive trips.
POSSIBLE CAUSES
ELECTRONIC AUTO TRANSAXLE TROUBLE CODES PRESENT
8-VOLT SUPPLY CIRCUIT OPEN
PCM DEF (NO VSS SIGNAL CKT)
PCM TERMINAL DEFECTIVE
VEHICLE SPEED SENSOR GROUND CIRCUIT OPEN
VEHICLE SPEED SENSOR SIGNAL CIRCUIT WIRING HARNESS OBSERVABLE DEFECT
PINION GEAR DEFECTIVE
OUTPUT SPEED SENSOR CIRCUIT OPEN
OUTPUT SPEED SENSOR CIRCUIT SHORTED TO GROUND
VEHICLE SPEED SENSOR SIGNAL CIRCUIT OPEN
VSS SIGNAL CIRCUIT SHORTED TO GROUND
OUTPUT SPEED SENSOR DEFECTIVE
OUTPUT SPEED SENSOR DEFECTIVE (RES > 5.0)
PCM DEFECTIVE (NO VSS SIGNAL CKT)
PCM DEFECTIVE (NO VSS SIGNAL CKT)
TCM DEFECTIVE (VSS SIG CKT)
VSS DEFECTIVE
153
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored and Set Condition:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored: With engine running. The PCM expects the signal to be high for 16
cycles while it monitors the brake switch signal during accel and decel modes.
Set Condition: After the vehicle speed increases, the PCM must accumulate 6 seconds
while delta throttle voltage is above 0.02 volt. The count is reset to zero whenever the
brake switch indicates a low signal.
POSSIBLE CAUSES
BRAKE SWITCH GROUND CIRCUIT OPEN
BRAKE SWITCH INTERNAL SHORT
BRAKE SWITCH SENSE CIRCUIT OPEN
BRAKE SWITCH SENSE CIRCUIT SHORT TO GROUND
PCM CONNECTOR OBSERVABLE DEFECT
PCM DEF (VOLTAGE HIGH)
PCM DEF (VOLTAGE LOW)
TEST ACTION APPLICABILITY
1 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With a Voltmeter, measure the Brake Switch Sense Circuit at the Brake Switch
Connector.
Is the voltage above 9.0 volts?All
Ye s®Go To 2
No®Go To 5
2 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Ground Circuit at the Brake Switch
Connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Repair the Brake Switch Ground Circuit.
Perform Powertrain Verification Test VER-2A.
172
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on with engine not running.
Monitor Brake Switch status on the DRB while performing the next step.
Connect a jumper across the Brake Switch Circuit to Ground Circuit.
Did the DRB change from9pressed9to9released9?All
Ye s®Replace or adjust the Brake Switch.
Perform Powertrain Verification Test VER-2A.
No®Go To 4
4 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit resistance from the
PCM to the Brake Switch Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Brake Switch Sense Circuit for an open.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Is any terminal damaged, pushed out, or miswired?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 7
7 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit to a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Brake Switch Sense Circuit for a short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
173
DRIVEABILITY
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
174
DRIVEABILITY
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED ÐContinued
ProCarManuals.com

Symptom:
P-1698 NO CCD MESSAGES FROM TCM
When Monitored and Set Condition:
P-1698 NO CCD MESSAGES FROM TCM
When Monitored: With the engine running.
Set Condition: No CCD messages are received from the TCM for 10 seconds.
POSSIBLE CAUSES
DRB DOES NOT SHOW BUS OPERATIONAL
CCD WIRING HARNESS OBSERVABLE DEFECT
CCD BUS (+) CIRCUIT OPEN BETWEEN PCM AND TCM
CCD BUS (-) CIRCUIT OPEN BETWEEN PCM AND TCM
PCM DEFECTIVE (NO CCD MESSAGE)
TCM DEFECTIVE (NO CCD MESSAGE)
TEST ACTION APPLICABILITY
1 Ignition On
With the DRB, select9Transmission9.
Note: The CCD Bus test is automatic.
Does the DRB show9Bus Operational9?All
Ye s®Go To 2
No®Go to the appropriate symptom group for body diagnostics.
2 Ignition Off
With the DRB, select9Engine9module.
With the DRB erase trouble codes.
Raise all four wheels off the ground and properly support the vehicle.
Caution: Keep clear of rotating wheels in the next step.
Start the engine. Place the Shift Lever in Drive and allow the wheels to rotate for 1
minute.
Step on the brakes, put the Shift Lever back in Park.
With the DRB read Trouble Codes.
Does display show9No CCD Message from TCM9and the start run counter equal to
zero?All
Ye s®Go To 3
No®Go To 7
224
DRIVEABILITY
ProCarManuals.com

Symptom:
* CHECKING FUEL DELIVERY
POSSIBLE CAUSES
FUEL LINE RESTRICTED
FUEL FILTER DEFECTIVE
FUEL LINE RESTRICTED
FUEL PRESSURE REGULATOR DEFECTIVE
FUEL PUMP/REGULATOR ASSEMBLY DEFECTIVE
FUEL RETURN LINE DEFECTIVE
FUEL PUMP/REGULATOR ASSEMBLY DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel Pressure.
Connect a Fuel Pressure Gauge to test port.
Ignition On, Engine Not Running
With the DRB, actuate Fuel System. Fuel Pressure should be 43 to 53 psi.
Fuel Pressure should be 43 to 53 psi.
Is the Fuel Pressure within the specification?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Go To 2
No®Go To 5
2 Ignition Off
Note: Make sure the Gear Lever is in neutral, and the Park Brakes engaged.
Start the engine.
Monitor the Fuel Pressure Gauge in the next step.
While monitoring the pressure, momentarily snap Throttle wide open raising RPM to
above 3000.
Did the fuel pressure drop below 35 psi at all?All
Ye s®Go To 3
No®Test Complete.
3 Ignition Off
Inspect the Chassis Fuel Supply Line to the engine for a kink or restriction.
Is the line kinked or restricted?All
Ye s®Release the fuel pressure. Repair the Fuel Line as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 4
237
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
8 Ignition Off
Inspect the Chassis Fuel Supply Line to engine for a kink or restriction.
Is the Line kinked or restricted?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Release the Fuel Pressure. Repair the Fuel Line as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 9
9 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the fuel pressure.
Connect a Fuel Pressure Adapter and Gauge to Supply Line between Tank/Filter.
Turn ignition on.
With the DRB, actuate the Fuel System test.
Is the Fuel Pressure at least 5 psi higher than previously recorded pressure?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Release the Fuel Pressure. Replace the Fuel Filter.
Perform Powertrain Verification Test VER-2A.
No®Go To 10
10 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Release the fuel pressure.
Connect a Fuel Pressure Adapter and Gauge to Supply Line between Tank/Filter.
Turn ignition on.
With the DRB, actuate the Fuel System test.
Is Fuel Pressure at least 5 psi higher than previously recorded pressure?ENGINE - 2.4L I-4
DOHC and/or EN-
GINE - 3.3L V6
and/or ENGINE -
3.3L V6 FFV and/or
ENGINE - 3.8L V6
Ye s®Test Complete.
No®Release the Fuel Pressure. Replace the Fuel Pump and Regulator
Assembly.
Perform Powertrain Verification Test VER-2A.
11 Ignition Off
Warning: The Fuel System must be opened and may be under high pressure.
Relieve the Fuel Pressure.
Tee-in Fuel Pressure Gauge into the Fuel Supply Hose using Tool #6433.
Turn ignition on.
With the DRB, actuate the ASD Fuel System test.
Is the Fuel Pressure between 43 and 53 psi?ENGINE - 3.0L V6
Ye s®Go To 12
No®Go To 15
12 Ignition Off
Note: Make sure the Gear Lever is in neutral, and the Park Brakes engaged.
Start the engine.
Monitor the Fuel Pressure Gauge in the next step.
While monitoring the pressure, momentarily snap Throttle wide open raising RPM to
above 3000.
Did the fuel pressure drop below 35 psi at all?All
Ye s®Go To 13
No®Test Complete.
239
DRIVEABILITY
* CHECKING FUEL DELIVERY ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE ENGINE MECHANICAL SYSTEMS
POSSIBLE CAUSES
CHECKING ENGINE MECHANICAL SYSTEMS
TEST ACTION APPLICABILITY
1 At this point in the diagnostic test procedure, you have determined that all of the
engine electrical systems are operating as designed; therefore, they are not the cause
of the driveability problem.
The following additional items should be checked as possible mechanical causes of
the problem:
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
CAMSHAFT LOBES - check for abnormal wear
CRANK SENSOR PICK-UP - check crankshaft slots for debris/deterioration
ENGINE EXHAUST SYSTEM - must be free of any restrictions
ENGINE PCV SYSTEM - must flow freely
ENGINE DRIVE SPROCKETS - must be properly positioned
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Note: If you came to this test from the oxygen sensor, and the rich or lean
condition is not caused by one of the first items above, replace the power-
train control module and perform TEST VER-2A (Road Test Verification).
Always look for any Technical Service Bulletins that may relate to the problem.
Did you come from an Oxygen Sensor rich or lean condition test?All
Ye s®Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
253
DRIVEABILITY
ProCarManuals.com

Symptom List:
P-1595 SPEED CONTROL SOLENOID CIRCUITS
P-1683 SPEED CONTROL POWER RELAY OR S/C 12V DRIVER
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-1595 SPEED CONTROL SOLE-
NOID CIRCUITS.
When Monitored and Set Condition:
P-1595 SPEED CONTROL SOLENOID CIRCUITS
When Monitored: Speed control on, vehicle speed > 25 mph, RPM < 5440, brake not
applied. For an automatic transmission, in drive mode. For a manual transmission, the
clutch not depressed.
Set Condition: The powertrain control module (PCM) actuates the vacuum and vent
solenoid but they do not respond.
P-1683 SPEED CONTROL POWER RELAY OR S/C 12V DRIVER
When Monitored: Speed control on, vehicle speed > 25 mph, RPM < 5440, brake not
applied. For an automatic transmission, in drive mode. For a manual transmission, the
clutch not depressed.
Set Condition: The powertrain control module (PCM) actuates the vacuum and vent
solenoids but they do not respond.
POSSIBLE CAUSES
S/C BRAKE SWITCH OUTPUT CIRCUIT OPEN
S/C BRAKE SWITCH OUTPUT CIRCUIT SHORTED TO GROUND
S/C VACUUM SOLENOID CONTROL CIRCUIT OPEN
S/C VENT SOLENOID CONTROL CIRCUIT OPEN
SPEED CONTROL POWER SUPPLY CIRCUIT OPEN
SPEED CONTROL SERVO GROUND CIRCUIT OPEN
BRAKE SWITCH DEFECTIVE
SPEED CONTROL SERVO DEFECTIVE
PCM DEFECTIVE (SC SOLENOID CIRCUIT)
PCM DEFECTIVE (SPEED CONTROL P/S CIRCUIT)
BRAKE SWITCH NEEDS TO BE ADJUSTED
256
SPEED CONTROL
ProCarManuals.com

TEST ACTION APPLICABILITY
1 Ignition Off
Note: A misadjusted Brake Switch can cause this code to set.
Does the Brake Switch need to be adjusted?All
Ye s®Adjust Brake Switch as necessary.
No®Go To 2
2 Ignition Off
Disconnect the Speed Control Servo 4-Way Connector.
Note: Check connectors - Clean/repair as necessary.
Note: Ensure the Brake pedal is not depressed during the following steps.
Engine off. Ignition key on and S/C On/Off Switch ON.
Using a Voltmeter, measure the voltage of the S/C Brake Switch Output Circuit at
Speed Control Servo Connector.
Is the voltage above 10.0 volts?All
Ye s®Go To 3
No®Go To 10
3 Ignition off.
Disconnect the Speed Control Servo Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of the Gnd Circuit at Servo Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 4
No®Repair the open Ground Circuit.
Perform Powertrain Verification Test VER-4A.
4 Ignition off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Note: Ensure the Brake pedal is not depressed during the following steps.
With an ohmmeter, test the resistance from the S/C Power Supply Circuit to the S/C
Vent Solenoid at PCM.
Is the resistance between 35 ohms and 55 ohms?All
Ye s®Go To 5
No®Go To 7
5 Ignition off
Disconnect Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Note: Ensure the Brake Pedal is not depressed during the following steps.
With an ohmmeter, test the resistance from the S/C Power Supply Circuit to the S/C
Vacuum Solenoid Control at PCM.
Is the resistance between 35 ohms and 55 ohms?All
Ye s®Go To 6
No®Go To 7
257
SPEED CONTROL
P-1595 SPEED CONTROL SOLENOID CIRCUITS ÐContinued
ProCarManuals.com