ECU CHRYSLER VOYAGER 2001 Workshop Manual

Symptom:
PCI BUS SHORTED TO BATTERY
When Monitored and Set Condition:
PCI BUS SHORTED TO BATTERY
When Monitored: Continuously with the ignition on.
Set Condition: The RKE/Thatcham Alarm Module has detected a short to battery voltage
on the PCI Bus.
POSSIBLE CAUSES
PCI BUS MALFUNCTION
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1NOTE: If this code is set and active it will be necessary to perform the PCI
Bus Communication Failure symptom.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?All
Ye s®Repair as necessary.
Perform VTSS VERIFICATION TEST - 1A.
No®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition. Look for any chafed, pierced, pinched or partially
broken wires.
Perform VTSS VERIFICATION TEST - 1A.
937
VEHICLE THEFT/SECURITY

Symptom:
PCI BUS SHORTED TO GROUND
When Monitored and Set Condition:
PCI BUS SHORTED TO GROUND
When Monitored: Continuously with the ignition on.
Set Condition: The RKE/Thatcham Alarm Module has detected a short to ground on the
PCI Bus.
POSSIBLE CAUSES
PCI BUS MALFUNCTION
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1NOTE: If this code is set and active it will be necessary to perform the PCI
Bus Communication Failure symptom.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?All
Ye s®Repair as necessary.
Perform VTSS VERIFICATION TEST - 1A.
No®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition. Look for any chafed, pierced, pinched or partially
broken wires.
Perform VTSS VERIFICATION TEST - 1A.
938
VEHICLE THEFT/SECURITY

Symptom:
PCM MESSAGES NOT RECEIVED
When Monitored and Set Condition:
PCM MESSAGES NOT RECEIVED
When Monitored: Continuously with the ignition on.
Set Condition: The RKE/Thatcham Alarm Module does not receive any messages from
the PCM for at least 5 seconds.
POSSIBLE CAUSES
INTERMITTENT CONDITION
PCM COMMUNICATION FAILURE
PCI BUS CIRCUIT OPEN
RKE/THATCHAM ALARM MODULE - INTERNAL MALFUNCTION
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRBIIIt, attempt to communicate with the PCM.
Was the DRBIIItable to communicate with the PCM?All
Ye s®Go To 2
No®Refer to the Communication category and perform the appropri-
ate symptom.
Perform VTSS VERIFICATION TEST - 1A.
2 Turn the ignition on.
With the DRBIIIt, attempt to communicate with the RKE/Thatcham Alarm Module.
Was the DRBIIItable to communicate with the RKE/Thatcham Alarm Module?All
Ye s®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition.
Perform VTSS VERIFICATION TEST - 1A.
No®Go To 3
3 Turn the ignition off.
Disconnect the RKE/Thatcham Alarm Module C1 harness connector.
Connect the diagnostic junction port tester #8339 to the diagnostic junction port.
NOTE: Do not connect the tester to the DRBIIIt.
Measure the resistance of the PCI Bus circuit between the diagnostic junction port
tester and the RKE/Thatcham Alarm Module C1 connector (cavity 13).
Is the resistance below 5.0 ohms?All
Ye s®Replace the RKE/Thatcham Alarm Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Repair the PCI Bus circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.
939
VEHICLE THEFT/SECURITY

Symptom:
VEHICLE THEFT ALARM INDICATOR OUTPUT OPEN
When Monitored and Set Condition:
VEHICLE THEFT ALARM INDICATOR OUTPUT OPEN
When Monitored: Continuously with the ignition on.
Set Condition: The BCM has detected an open in the VTSS Indicator Driver circuit.
POSSIBLE CAUSES
INTERMITTENT CONDITION
VTA LAMP FUNCTIONAL TEST
VTSS INDICATOR DRIVER CIRCUIT OPEN
BODY CONTROL MODULE INTERNAL MALFUNCTION
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRBIIIt, erase the current Body Control Module DTC's.
Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIIIt, read the current Body Control Module DTC's.
Does the DRBIIItdisplay: VTA INDICATOR OUTPUT OPEN?All
Ye s®Go To 2
No®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition.
Perform VTSS VERIFICATION TEST - 1A.
2 With the DRBIIIt, actuate the VTA Indicator Lamp.
Did the VTA Lamp flash on and off during the actuation?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Go To 3
3 Disconnect the Message Center harness connector.
Disconnect the Body Control Module C4 harness connector.
Measure the resistance of the VTSS Indicator Driver circuit.
Is the resistance below 5.0 ohms?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Repair the VTSS Indicator Driver circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.
940
VEHICLE THEFT/SECURITY

Symptom:
VEHICLE THEFT ALARM INDICATOR OUTPUT SHORT
When Monitored and Set Condition:
VEHICLE THEFT ALARM INDICATOR OUTPUT SHORT
When Monitored: Continuously with the ignition on.
Set Condition: The BCM has detected a short to ground in the VTSS Indicator Driver
circuit.
POSSIBLE CAUSES
INTERMITTENT CONDITION
MESSAGE CENTER INTERNAL MALFUNCTION
BODY CONTROL MODULE INTERNAL MALFUNCTION
VTSS INDICATOR DRIVER CIRCUIT SHORTED TO GROUND
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRBIIIt, erase the current Body Control Module DTC's.
Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIIIt, read the current Body Control Module DTC's.
Does the DRBIIItdisplay: VTA INDICATOR OUTPUT OPEN?All
Ye s®Go To 2
No®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition.
Perform VTSS VERIFICATION TEST - 1A.
2 Disconnect the Body Control Module C4 connector.
Measure the resistance between ground and the VTSS Indicator Driver circuit.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
3 Disconnect the Body Control Module C4 connector.
Disconnect the Message Center connector.
Measure the resistance of the VTSS Indicator Driver circuit to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the VTSS Indicator Driver circuit for a short to ground.
Perform VTSS VERIFICATION TEST - 1A.
No®Replace the Message Center assembly.
Perform VTSS VERIFICATION TEST - 1A.
941
VEHICLE THEFT/SECURITY

Symptom:
*ALARM TRIPS ON ITS OWN
POSSIBLE CAUSES
ALARM TRIPPED BY
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1 With the DRBIIIt, read the Alarm Tripped By status.
Were there any causes displayed?All
Ye s®Refer to Symptom List for problems related to the component
indicated by the DRBIIIt.
Perform VTSS VERIFICATION TEST - 1A.
No®The condition that caused this symptom is currently not present.
Inspect the related wiring harness for a possible intermittent
condition. Look for any chafed, pierced, pinched or partially
broken wires.
Perform VTSS VERIFICATION TEST - 1A.
942
VEHICLE THEFT/SECURITY

Symptom:
*HOOD DOES NOT TRIP VTSS
POSSIBLE CAUSES
CHECK DRBIIItFOR HOOD AJAR SWITCH RESPONSE
BODY CONTROL MODULE
TEST ACTION APPLICABILITY
1 With the DRBIIIt, read the HOOD AJAR SW status.
Open the hood.
Does the DRBIIItdisplay CLOSED?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Refer to symptom HOOD AJAR CKT OPEN in the DOOR AJAR
category.
Perform VTSS VERIFICATION TEST - 1A.
943
VEHICLE THEFT/SECURITY

Symptom:
*LEFT FRONT DOOR DOES NOT TRIP VTSS
POSSIBLE CAUSES
BODY CONTROL MODULE
CHECK DRBIIItFOR DRIVER DOOR AJAR RESPONSE
TEST ACTION APPLICABILITY
1 With the DRBIIIt, read the DRVR DOOR AJAR SW status.
Open the driver door.
Does the DRBIIItdisplay CLOSED?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Refer to symptom DRIVER DOOR AJAR CKT OPEN in the
DOOR AJAR category.
Perform VTSS VERIFICATION TEST - 1A.
944
VEHICLE THEFT/SECURITY

Symptom:
*LEFT SLIDING DOOR DOES NOT TRIP VTSS
POSSIBLE CAUSES
MONITOR DRBIIItFOR LEFT SLIDING DOOR AJAR STATUS
BODY CONTROL MODULE
TEST ACTION APPLICABILITY
1 With the DRBIIIt, read the LSLIDE DR AJAR SW status.
Open the left sliding door.
Does the DRBIIItdisplay the switch state as CLOSED?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Refer to symptom LEFT SLIDING DOOR AJAR CKT OPEN in
the DOOR AJAR category.
Perform VTSS VERIFICATION TEST - 1A.
945
VEHICLE THEFT/SECURITY

Symptom:
*LIFTGATE DOES NOT TRIP VTSS
POSSIBLE CAUSES
CHECK DRBIIItFOR LIFTGATE SW RESPONSE
BODY CONTROL MODULE
TEST ACTION APPLICABILITY
1 With the DRBIIIt, read the LIFTGATE AJAR SW status.
Open the liftgate.
Does the DRBIIItdisplay CLOSED?All
Ye s®Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.
No®Refer to symptom LIFTGATE AJAR CKT OPEN in the DOOR
AJAR category.
Perform VTSS VERIFICATION TEST - 1A.
946
VEHICLE THEFT/SECURITY