ABS Citroen BERLINGO FIRST 2011.5 1.G Owner's Manual

3CONTENTS
-
110 - 117  AUDIO
RD3 audio system 110
118 - 122  VISUAL INDEX 58 - 63  LIFE ON BOARD
Front fi ttings 58
Courtesy lamps 59
Headlamp adjustment 60
Steering wheel adjustment 60
Lashing rings 61
Rear fi ttings 62
64 - 71  DRIVING
Handbrake 64
ABS and EBFD systems 64
Speed limiter 65
Cruise control 67
Airbags 69
72 - 97  PRACTICAL INFORMATION
Under the bonnet 72
Levels 77
Checks 78
Changing a wheel 79
Changing a bulb 82
Changing a fuse 88
Battery 92
Energy economy mode 92
Fitting audio equipment, speakers 93
Snow screen 94
Towing 95
Towing a trailer 96
Accessories 97
98 - 109  TECHNICAL DATA
Dimensions 98
Engines 102
Light van weights and loads 105
Ludospace weights
and loads 107
Identifi cation features 109

MONITORING and DISPLAY SCREENS
20 -


1.
Seat belt not fastened warning
lamp

2.
Passenger's airbag deactivated
warning lamp

3.
Front and lateral airbags warning
lamp

4.
Front foglamps warning lamp

5.
Anti-lock braking system (ABS)
warning lamp

6.
Rear foglamp warning lamp

7.
Diesel pre-heater warning lamp

8.
Left hand direction indicator
9.
Total distance recorder, service
indicator and engine oil level
indicator

10.
Right hand direction indicator

11 .
Emission control system warning
lamp

12.
Main beam headlamps warning
lamp

13.
Parking brake, low brake fl uid
level and electronic brake force
distribution fault warning lamp

14.
Dipped beam headlamps
warning lamp

15.
Battery charge warning lamp

16.
Engine oil pressure and
temperature warning lamp
17.
Water in Diesel fi lter warning
lamp

18.
Low coolant level warning lamp

19.
Coolant temperature indicator

20.
Total distance recorder button

21.
Central (STOP) warning lamp

22.
Speedometer *

23.
Rev counter

24.
Lighting dimmer button

25.
Fuel gauge

26.
Low fuel level warning lamp

27.
Speed limiter/cruise control
screen

INSTRUMENT PANEL: PETROL - DIESEL


*
Version indicating in miles or kilo-
metres according to country of sale.

21MONITORING and DISPLAY SCREENS
-
MONITORING OPERATION


A warning lamp on fi xed or fl ash-
ing, with the engine running, in-
dicates an fault in the operation
of the unit concerned. The illumi-
nation of certain warning lamps
may be accompanied by an audi-
ble signal and a message in the
screen. Do not ignore this warn-
ing: consult a
CITROËN dealer as
soon as possible.


If the central STOP warning lamp
comes on when you are driving,
stop your vehicle immediately,
where it is safe to do so.



Central (STOP)
warning lamp
Engine oil pressure
and temperature
warning lamp
Linked to the central (STOP) warning
lamp.

You must stop.

This warning lamp indicates one of
the following:


- low oil pressure indicated by the
message "Oil pressure insuffi -
cient"
in the screen.

- low engine oil level. Top up the
level.

- oil temperature too high. To lower
the oil temperature, reduce your
speed.
Illumination of the warning lamp is
accompanied by an audible signal.
Consult a CITROËN dealer.


Low engine coolant
level warning lamp
Linked to the central (STOP) warn-
ing lamp.
This comes on for a few seconds
when the ignition is switched on.
Illumination of this warning lamp is
accompanied by an audible signal
and the message "Top up engine
fl uid level"
in the screen.

You must stop as soon as it is safe
to do so.

Wait for the engine to cool before
topping up the level.
The cooling system is pressurised.



Parking brake, low
brake fluid level and
Electronic Brake Force
Distribution system
fault warning lamp
Linked to the central (STOP) warning
lamp.
This comes on each time the ignition
is switched on.
Illumination of this warning lamp is
accompanied by an audible signal
and a message in the screen indicat-
ing the cause of the warning:


- "Handbrake on",
if the parking
brake is applied or not fully re-
leased.

- "Brake fl uid level low"
if there is
an excessive drop in brake fl uid
level (if the warning lamp remains
on even when the parking brake
is released).

- "Braking fault"
is displayed to-
gether with the ABS warning
lamp, indicating a fault with the
Electronic Brake Force Distribu-
tion system. You must stop as
soon as it is safe to do so.


Consult a CITROËN dealer. If a check is required, to prevent any
risk of burns
unscrew the cap by
two turns to allow the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Consult a CITROËN dealer.
Linked to the warning lamps for:


- ''engine oil pressure and temper-
ature'',

- "low coolant level'',

- "parking brake'',

- ''low brake fl uid level'',

- ''electronic brake force distribution
system fault''.
Linked with the "coolant temperature"
gauge.

You must stop if the lamp fl ashes
with the engine running.

Consult a CITROËN dealer.

MONITORING and DISPLAY SCREENS
22 -

Battery charge warning
lamp
This comes on for a few sec-
onds when the ignition is
switched on. Illumination of this warn-
ing lamp, when the engine is running,
accompanied by an audible signal
and the message "Battery charge
fault"
in the screen, indicates one of
the following:


- malfunction of the charging circuit,

- loose battery or starter terminals,

- a cut or loose alternator belt,

- an alternator failure.
Consult a CITROËN dealer.


Emission control
system warning lamp
This comes on for a few
seconds each time the igni-
tion is switched on.
If it comes on with the engine running,
accompanied by an audible signal
and the message in the screen:


- "Antipollution fault",
this indi-
cates a fault with the emission
control system.

- "Catalytic converter fault",
this
indicates a fault with the injection
or ignition system. There is a risk of
damage to the catalytic converter
(petrol engine only).
Consult a CITROËN dealer.


Diesel engine
pre-heater warning
lamp

Wait until the warning lamp goes out
before starting the engine.
If the temperature is high enough,
the warning lamp comes on for less
than one second. You can start the
engine without waiting.


Low fuel level
warning lamp
This comes on for a few
seconds when the igni-
tion is switched on.
When the ignition is on, it is accom-
panied by an audible signal and the
message "Fuel level low"
in the
screen.
If it fl ashes with the fuel gauge nee-
dle in the lowest position, when the
ignition is on, this indicates a fault
with the fuel gauge.
When this warning lamp comes on,
you have enough fuel left to drive ap-
proximately 30 miles (50 km)
.
Capacity of the tank:


- approximately 55 litres for petrol
engines,

- approximately 60 litres for Diesel
engines.



Water in Diesel filter
warning lamp *

There is a risk of damage to the in-
jection system.
Contact a CITROËN dealer as soon
as possible.


Anti-lock braking
system (ABS) warning
lamp
This comes on for a few seconds each
time the ignition is switched on.
If the warning lamp remains on or
comes on above 8 mph (12 km/h),
this indicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Illumination of this warning lamp,
accompanied by an audible signal
and the message "ABS fault"
in the
screen, indicates an ABS fault.
Consult a CITROËN dealer.

*
According to country.

35SEATS-
FRONT SEATS



The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.


To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
4. Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.

2. Armrests
These can be folded back.
3. Seat back angle adjustment

5. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops ope-
ration.

Note:
the command for activation of
heating of the seat(s) remains memo-
rised for two minutes after the ignition
has been switched off.
6. Access to rear seats
(version with one
sliding side door only)


A.
Turn the knob.

B.
Pull the lever (version
with one sliding side
door only).

Never drive with the head re-
straints removed; they must
be in place and correctly ad-
justed. No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).

SEATS36-
To fold the rear bench seat:


- lower the head restraint,

- press control 1
to unlock the seat
back 2
,

- fold the seat back 2
onto the seat,

- place the seat in the "folded" po-
sition. When repositioning:


- tilt the folded seat rearwards,

- lift the seat back,

- check that the seat is locked cor-
rectly.

Take care not to trap the seat belts.
On the 4-seat version, each rear seat
has a fi xed rear head restraint and a
seat belt.
REAR BENCH SEAT(4/5 SEAT VERSIONS)
Head restraint

This is of the "comma-shape" type.
High position: press the two tabs at
the same time, lift the head restraint
and raise it.
Low position: push the two tabs at
the same time and press the top to
lower the head restraint.
To remove the head restraint: place
it in the high position, lift it then re-
move it.
Store it inside the vehicle, securing
it fi rmly.
To install the head restraint: engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.

37SEATS-
GENERAL POINTS ON SEATBELTS
CHILD SEAT AT THE FRONT


"Forwards-facing"
When a "forwards-facing" child seat
is installed on the front passenger
seat
, adjust the vehicle's seat to the
intermediate longitudinal position
with the seat back upright and leave
the passenger's airbag activated.

Intermediate longitudinal
position
"Rearwards-facing"
When a "rearwards-facing" child seat
is installed on the front passenger
seat
, you must deactivate the pas-
senger's airbag * . Otherwise, the
child would risk being seriously
injured or killed if the airbag were
to infl ate
.

*
The rules for carrying children are
specifi c to each country. Refer to the
current legislation in your country.
The procedures for the use of child
seats and deactivation of the pas-
senger's airbag are common to the
entire CITROËN range.
In the absence of passenger airbag
deactivation, it is strictly forbidden to
install a child seat in the "forwards
facing" position on the front passenger
seat.
Although one of CITROËN's main
criteria when designing your vehicle,
the safety of your children also de-
pends on you.
For maximum safety, please follow
these precautions:


- all children under the age of 12
or less than one metre fi fty tall
must travel in approved child
seats suited to their weight
,
on seats fi tted with a seat belt or
ISOFIX mountings * .

- a child weighing less than 9 kg
must travel in the "rearwards-
facing" position in the front.

43SEATS-
ADVICE ON CHILD SEATS Children under the age of 10 must not
travel in the "forward facing" position
on the front passenger seat, unless
the rear seats are already occupied
by other children, cannot be used or
are absent.
Deactivate the passenger's airbag
when a "rear facing" child seat is in-
stalled on the front seat. Otherwise,
the child would risk being seriously
injured or killed if the airbag were to
infl ate. As a safety precaution, do not leave:


- one or more children alone and
unsupervised in a vehicle,

- a child or an animal in a vehicle
which is exposed to the sun, with
the windows closed,

- the keys within reach of children
inside the vehicle.

Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
CITROËN recommends the use of
a booster seat which has a back, fi t-
ted with a seat belt guide at shoulder
level. To prevent accidental open-
ing of the doors, use the
"Child lock". The incorrect installation of a child
seat in a vehicle compromises the
child's protection in the event of an
accident.
Remember to fasten the seat belts
or the child seat harnesses keep-
ing the slack
in relation to the child's
body to a minimum
, even for short
journeys.
For optimum installation of the "for-
ward facing" child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle's seat
and that the head restraint does not
cause any discomfort.
If the head restraint has to be removed,
ensure that it is stored or attached se-
curely to prevent it from being thrown
around the vehicle in the event of
sharp braking. Take care not to open the rear win-
dows by more than one third.
To protect young children from the
rays of the sun, fi t side blinds on the
rear windows.

ACCESS and STARTING48 -

*
According to country.

THE ALARM SYSTEM *

The alarm offers two types of protection:



- exterior protection:
the alarm
sounds if a door, the boot or the
bonnet is opened
;

- interior protection:
the alarm
sounds if there is a variation in
the volume inside the vehicle
(breaking of a window or move-
ment inside the vehicle)
.


Setting the alarm
Switch the ignition off and get out of
the vehicle.
Activate the alarm within fi ve minutes
following your exit from the vehicle,
by locking using the remote control
key (the red indicator lamp in the
switch 1
, which can be seen from the
outside, fl ashes once a second).
Warning
If, on setting the alarm, a door, the
boot or the bonnet are not closed
correctly, the siren sounds for a mo-
ment.
Close the vehicle correctly to set the
alarm.
If the interior protection alarm is trig-
gered ten times in succession, it is
disarmed automatically. It must be
set again in order for it to operate
correctly. When the alarm is triggered, the
siren sounds and the direction indi-
cators fl ash for thirty seconds.
After it has been triggered, the alarm
becomes operational again.

Note:
if you wish to lock your vehicle
without setting the alarm, lock it us-
ing the key in the door lock.

Disarming the alarm
Unlock the vehicle using the remote
control key (the red indicator lam in
the switch 1
goes off).

Note:
if the warning light fl ashes, it is
a sign that the alarm has been trig-
gered in your absence.
To stop it, switch on the ignition.
Note:
when the alarm is set, but the
remote control no longer works:


)
unlock the doors using the key
and open the door; the alarm is
triggered;

)
switch the ignition on within ten
seconds; the alarm is disarmed.


To set the alarm with exterior
protection only.
If, while you are away from the vehicle,
you wish to leave a window partially
open or a pet inside the vehicle, you
need to select exterior protection only:


●
Switch off the ignition.

●
Press the button 2
until the lamp 1

comes on continuously.

●
Get out of the vehicle.

●
Press the locking button of the re-
mote control.

●
The doors lock.

●
The red lamp in the switch fl ash-
es once a second.




Operating fault

When the ignition is switched on, fi xed
illumination of the red indicator lamp,
located in the centre of the dashboard,
indicates an anomaly with the siren.
Contact a CITROËN dealer to have
the system checked.
Do not make any modifi ca-
tions to the alarm system, this
could cause malfunctions.

DRIVING64 -
HANDBRAKE
Illumination of this warning
light and of the STOP
warn-
ing light, accompanied by
an audible signal (while the
vehicle is moving), indicates that the
handbrake is still applied or has not
been released fully.


ANTI-LOCK BRAKING
SYSTEM (ABS) AND THE ELECTRONIC BRAKE FORCEDISTRIBUTION (EBFD)
The ABS, in conjunction with the
electronic brake force distribution,
increases the stability and manoeu-
vrability of your vehicle on braking,
in particular on poor or slippery road
surfaces.

Note:
when changing wheels (tyres
and rims), make sure that these are
approved.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.

When this warning light comes
on, connected to the STOP

and ABS
warning lights, it
indicates that there is a mal-
function of the electronic brake force
distribution, which can cause a loss of
control of the vehicle when braking.


Stop immediately.

In both cases, consult a CITROËN
dealer. When this warning light
comes on, accompanied by a
buzzer, it indicates that there
is a malfunction of the ABS,
which can cause a loss of control of
the vehicle when braking. Normal operation of the ABS may
make itself felt by slight vibrations
of the brake pedal.

In emergency braking, press
very fi rmly without releasing the
pressure.



Releasing
Pull the handle and press the button
to release the handbrake.
Applying
When parking, pull the handbrake to
immobilise your vehicle.