remove seats Citroen BERLINGO FIRST DAG 2008 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: BERLINGO FIRST DAG, Model: Citroen BERLINGO FIRST DAG 2008 1.GPages: 114, PDF Size: 1.55 MB
Page 5 of 114
FAMILIARISATION8 -
FRONT SEATS
Never travel with the head
restraints removed.
2. Armrest.
3. Seat back angle adjustment.
4. Forwards-backwards adjustment.
5. Storage drawer (passenger).
40
1. Head restraint height adjustment.
Page 39 of 114
41SEATS-
FRONT SEATS
The adjustment is correct when
the upper edge of the head
restraint is level with the top of
the head.
To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
4. Forwards-backwards
adjustment
Lift the control and slide the seat
forwards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.
2. Armrests
These can be folded back. 3. Seat back angle adjustment
5. Storage drawer (version with
passenger air bag)
There is a storage drawer under the
front passenger seat.
To open it, lift it and pull. 6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops
operation.
Note: the command for activation
of heating of the seat(s) remains
memorised for two minutes after the
ignition has been switched off.
7. Access to rear seats (version with one
sliding side door only)
Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).
Do not place heavy objects
in the drawers.
A. Turn the knob.
B. Pull the lever (version
with one sliding side door
only).
Never drive with the head re-
straints removed; they must
be in place and correctly ad-
justed.
Page 40 of 114
SEATS42 -
MULTIFUNCTION PASSENGER SEAT
To fold the seat fully:
Pull the control 2 upwards and tilt the
whole seat.
It is not necessary to remove the
head restraint.
This provides access to a box which
enables you to store objects so that
they cannot be seen from outside the
vehicle. I f y o u r v e h i c l e i s n o t fi t t e d w i t h a l o a d
blocking partition, it can accommo-
date long objects (up to 2.10 m).
These must be placed on the front
e d g e o f t h e fl o o r a n d s e c u r e d u s i n g
the rear bar of the boot or using the
lashing rings.
To fold the seat back:
Pull the control
1 upwards and tilt the
seat back.
T h i s p r o v i d e s a fl a t s u r f a c e , r e c e s s e s
for drinks and a strap for retaining
documents.
Page 70 of 114
69COMFORT AND SAFETY-
1.
Trays between the front and
rear seats
2. Load-space cover
To install it:
- position the front ends of the load space cover on its support and press gently to put it in place,
- unfold the load space cover fully,
- position the rear ends of the load space cover on its support and press gently to put it in place.
To remove it:
- unclip the rear ends,
- fold the load space cover fully,
- unclip the front ends and remove the load space cover.
To store it, fold it like an accordion. Do not roll it .
3. Stowing rings
4. High load retaining net
The high load retaining net can be fi t t e d b e h i n d t h e f r o n t o r r e a r s e a t s .
Open the covers A of the corresponding Aupper fastenings.
Fit the ends of the metal bar in these fastenings.
Secure the two net strap hooks be-hind the front seats, with the rear seat folded, or in the stowing rings B o n t h e fl o o r .
The rings are located directly below the corresponding upper fastenings.
Pull the two straps C taut.
5. Side door storage compartments
6. Seat back storage pockets