brake light Citroen BERLINGO MULTISPACE 2016 2.G User Guide

160
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Checks
Good practice
Bleeding water from the Diesel
filter
Manual gearbox
Have the level checked in accordance with the
  manufacturer's   servicing   schedule.
In order to avoid damaging the electrical units, we strongly
advise you not to use high
pressure washing to clean the engine
compartment.
After
  washing   the   vehicle   dampness,  
or

 
in
  winter,   ice   may   form   on   the   brake  
discs

  and   pads:   braking   efficiency   may  
be

 
reduced.   Make   some   light   brake  
applications to dry and de-ice the
brakes.
If

 
this
 
warning
 
lamp
 
comes
 
on,

 
bleed
 
the
 
filter.
 
Otherwise
 
bleed

 
regularly
 
each
 
time
 
the
 
engine

 
oil
 
is
 
changed.
H

d
i engines use advanced
technology.
 
All

 
work
 
requires
 
special training, so should be
entrusted

 
to
 
a
 
CITROËN
 
dealer.
Depending
 
on
 
country
 
of
 
sale.
To drain the water, unscrew the bleed
screw
 
located
 
on
 
the
 
filter.
o

perate until all of the water no longer
flows
 
in
 
the
 
transparent
 
pipe,
 
then
 
tighten

 
the
 
bleed
 
screw.
Only  use   products   recommended   by  
CITR

o Ë n or products of equivalent
quality   and   specification.
In
 
order   to   optimise   the   operation  
of

 
units   as   important   as   the   braking  
system,

  CITROËN   selects   and   offers  
specific

  products.

172
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
1. Parking the vehicle
- The  occupants   must   get   out   of   the  vehicle
  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 Place   a   chock   under   the   wheel  diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. T

ools
The tools are stowed in a storage area
closed  by   a   flap   under   a   front   seat.
-
 
If
  necessary,   move   the   seat   forward  
to

  access   the   storage   compartment  
from

  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-
 
Remove
  the   tools   needed   from   the  
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 
it

 
is
 
sometimes
 
necessary
 
to
 
raise
 
the

 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to

 
remove
 
the
 
spare
 
wheel
 
from
 
its
 
carrier

.
On
 
certain
 
types
 
of
 
ground
 
and/
or if considerable loads are being
transported, call a CITR
o
Ë
n
dealer or
a
 
qualified
 
workshop.
The
 
jack
 
and
 
tools
 
are
 
specific
 
to
 
your
 
vehicle.

 
Do
 
not
 
use
 
them
 
for
 
other
 
purposes.
Changing a wheel

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb

196
Berlingo-2-VP_en_Chap09_Caract-technique_ed01-2016
ENGINE CHARACTERISTICS
The engine characteristics (capacity,
maximum  power,   maximum   power  
speed, fuel, C

o
2 emissions...) for your vehicle are given in the registration
certificate.
These characteristics correspond
to the values type-approved
on a test bed, under conditions
defined
 
in
 
European   legislation  
(Directive 1999/99/EC).
For

 
more
 
information,   refer   to   the  
manufacturer's

 
website   or   sales  
brochure

 
for
 
the
  model.   Contact  
a

 
CITROËN
 
dealer   or   a   qualified  
workshop.
WEIGHTS AND TOWED LOADS
These values, expressed in kg, can be found
  on   the   manufacturer's   VIN   plate  
or

  label.
The
  maximum   weights   and   towed  
loads for your vehicle can be found on
the

  vehicle's   registration   certificate.
The
  kerb   weight   is   equal   to   the   weight  
without

  load   +   driver   (75   kg)   +   fuel   tank  
filled

  to   90%.
The GTW and towed load values
indicated
  are   valid   up   to   a   maximum  
altitude

  of   1000   metres.  
The
  value   of  
the

  towed   load   mentioned   must   be  
reduced by 10 % for each additional
1000

  metres.
With
  load   transfer,   the   braked   trailer  
weight can be increased, on condition
that the equivalent of this load is
removed

  from   the   vehicle   so   that   the  
GTW

  is   not   exceeded. High
  ambient   temperatures  
may

  result   in   a   reduction   in   the  
performance

  of   the   vehicle   in  
order

  to   protect   the   engine.   When   the  
ambient

  temperature   is   higher   than  
37 °C,

  limit   the   towed   weight.
Towing with a lightly loaded
vehicle can adversely affect road
holding.
Towing
  a   trailer   increases   braking  
distances.
When

  towing,   the   maximum   permitted  
speed

  is   reduced   (comply   with   the  
legislation

  in   force   in   the   country).
The
  recommended   nose   weight   is  the downward force on the towball
(removable
  with   or   without   tools).
GVW: gross vehicle weight, the
maximum
  authorised   weight.
GTW:
  gross   train   weight,   the   maximum  
weight

  for   vehicle   plus   trailer.
The
  location   of   the   manufacturer's  
plate

  is   given   in   chapter   9,  
"Identification

  markings"   section.
In
  each   country,   it   is   imperative   that  
the

  maximum   towed   loads   authorised  
by

  local   legislation   are   complied  
with.

 
T
o   find   out   your   vehicle's   towing  
capacities and its gross train weight,
consult

  a   CITROËN   dealer.
Weights