warning Citroen BERLINGO MULTISPACE RHD 2016 2.G Owner's Guide

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls

11 4
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   in   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely

ABS
ABS
11 8
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
ANTI-LOCK BRAKING SYSTEM
(ABS / EBFD)
The ABS   and   EBFD   (electronic   brake  force
  distribution)   systems   improve   the  
stability

  and   manoeuvrability   of   your  
vehicle

  on   braking,   in   particular   on  
poor

  or   slippery   surfaces.
The
 
ABS
  prevents   locking   of   the  
wheels, the EBF

d provides control of
the
  braking   pressure   wheel   by   wheel.If
  this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, it indicates a
malfunction

  of   the  
ABS
  which  
could result in a loss of control of the
vehicle

  on   braking.
If
  this   warning   lamp   comes  
on,

  together   with   the   brake  
and

  STOP
 
warning   lamps,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen,

  it   indicates   a   malfunction   of  
the

  electronic   brake   force   distribution  
which could result in a loss of control of
the

  vehicle   on   braking.
EMERGENCY BRAKING
ASSIST

ANCE (EBA)
In an emergency, this system enables the  optimum   braking   pressure   to   be  
reached

  more   quickly,   press   the   pedal  
firmly

  without   releasing   it.
It is triggered by the speed at which the
brake
  pedal   is   pressed   down.
This
  alters   the   resistance   of   the   brake  
pedal

  under   your   foot.
To
  maintain   operation   of   the  
emergency

  braking   assistance   system:  
keep

  your   foot   on   the   brake   pedal.
Good practice
The anti-lock braking system comes into  operation   automatically   when  
there

  is   a   risk   of   wheel   lock.   It   does   not  
reduce

  the   braking   distance.
o

n very slippery surfaces (ice,
oil, etc...)
  the  
ABS
  may   increase   the  
braking

  distance.   When   braking   in  
an

  emergency,   do   not   hesitate   to  
press

  the   brake   pedal   firmly,   without  
releasing the pressure, even on a
slippery surface, you will then be able
to

  continue   to   manoeuvre   the   vehicle  
to

  avoid   an   obstacle.
Normal
  operation   of   the  
ABS
  may   be  
felt

  by   slight   vibration   of   the   brake  
pedal.
When changing wheels (tyres and
rims),

  ensure   that   these   are   listed   by  
CITROËN

  for   the   vehicle. Stop as soon as it is safe to do so.
In both cases, contact a CITR
o Ë n
dealer
  or   a   qualified   workshop.
driving safely

 119
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
ANTI-SLIP REGULATION (ASR)
AND

DYNAMIC STABILITY

CONTROL (DSC)
These systems are linked and complement  the  ABS.
The
 
ASR
  system   is   very   useful   for  
maintaining

  optimum   drive   and  
avoiding losses of control of the vehicle
on

  acceleration.
The
  system   optimises   drive   to   prevent  
the

  wheels   skidding,   by   acting   on   the  
brakes

  of   the   drive   wheels   and   on   the  
engine.

  It   also   allows   the   directional  
stability

  of   the   vehicle   to   be   improved  
on

  acceleration.
Use the
d SC to hold your course
without
  attempting   to   countersteer.
If there is a variation between the
trajectory
  followed   by   the   vehicle   and  
that required by the driver

, the d SC
system
  automatically   acts   on   the  
engine

  and   the   brake   of   one   or   more  
wheels,

  in   order   to   put   the   vehicle   back  
on

  course.
Deactivation
In certain exceptional conditions
(starting   the   vehicle   when   stuck   in   mud  
or

  snow,   or   on   loose   ground...),   it   could  
prove useful to deactivate the a

SR and
DSC
  systems   to   make   the   wheels   spin  
and

  regain   grip.
Operating fault
Good practice
The ASR/DSC   systems   offer   increased  safety
  during   normal   driving,   but  
should

  not   incite   the   driver   to   take   risks  
or

  to   drive   at   high   speed.
The
  operation   of   these   systems   is  
ensured

  if   the   recommendations  
of

  the   manufacturer   regarding  
the

  wheels   (tyres   and   rims),   the  
braking

  components,   the   electronic  
components

  and   the   fitting   and   repair  
procedures

  are   observed.
After
  an   impact,   have   these   systems  
checked

  by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Operation
The warning lamp flashes when operation of the a SR or
DSC
  is   triggered.
They engage again:
-
 
automatically
  above   30   mph  
(50
 
km/h), When
  a   malfunction   of   the  systems
  occurs,   the   warning  
lamp

  and   the   LED   come   on,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen.
-


Press the button or turn
the dial to the

d SC o FF
position (depending on
model).
-
 
The

 
LED   comes   on:   the  
ASR
  and  
DSC

 
systems   no   longer   come   into  
play

. -
 
manually
  by   pressing   the  
button again or by turning
the dial to this position
(depending

  on   model).Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
The

  warning   lamp   may   also   come   on   if  
the

  tyres   are   under-inflated.   Check   the  
pressure

  of   each   tyre.
driving safely
SaFETY
5

126
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
SEAT BELTS
Height adjustment
Squeeze the control with the return and
slide  the   assembly   on   the   driver's   seat  
side and on the individual passenger
seat

  side.
Fastening
Pull the strap, then insert the tongue
into  the   buckle.
Check
  that   the   seat   belt   is   fastened  
correctly

  by   pulling   the   strap.
Seat belt(s) not fastened
warning lamp Unfastening
Press the red button.
When the vehicle is started,
this
  warning   lamp   comes   on  
if a user at the front has not
fastened

  their   seat   belt.
Good practice
The driver must ensure that passengers use the seat belts correctly
and that they are all strapped in
securely  before   moving   off.
Wherever you are seated in the
vehicle, always fasten your seat belt,
even
  for   short   journeys.
The
  seat   belts   are   fitted   with   an   inertia  
reel

  which   automatically   adjusts   the  
length

  of   the   strap   to   your   size.
d

o not use accessories (clothes pegs,
clips,
  safety   pins,   etc.)   which   allow   the  
seat

  belt   straps   to   fit   loosely.
Ensure that the seat belt has reeled in
correctly
  after   use.
After
  folding   or   moving   a   seat   or   a   rear  
bench seat, ensure that the seat belt
has reeled in correctly and that the
buckle

  is   ready   to   accommodate   the  
tongue.
d

epending on the nature and
seriousness
  of   any   impact,   the  
pretensioning

  device   may   be   deployed  
before

  and   independently   of   inflation  
of

  the   airbags.   It   instantly   tightens  
the seat belts against the body of the
occupants.
Deployment

  of   the   pretensioners   is  
accompanied

  by   a   slight   discharge  
of

  harmless   smoke   and   a   noise,   due  
to the activation of the pyrotechnic
cartridge

  incorporated   in   the   system.
The
 
front
 
passenger's
 
seat
 
may
 
be
 
fitted

 
with

 
a

 
presence

 
detector

,
 
in

 
which

 
case you should not place anything
heavy on this seat as this could trigger
the

 
alert.
Seat belts

 127
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
Recommendations for children:
-
use a suitable child seat if the
passenger is less than 12 years old
or

  shorter   than   one   metre   fifty,
-

never allow a child to travel on
your lap, even with the seat belt
fastened. For

  more   information   on   child  
seats, refer to the "Child safety"
section

  of   chapter   5.
Clean the seat belt straps with
soapy water or a textile cleaning
product, sold by CITR
o Ë n
dealers.
In accordance with current safety
regulations, your CITR
o Ë n dealer can
guarantee
  all   work   or   any   checks,   from  
testing

  to   maintenance,   on   your   seat  
belt

  equipment.
Have
  the   seat   belts   checked   regularly  
(even

  after   a   minor   impact)   by   a  
CITROËN

  dealer   or   a   qualified  
workshop:

  they   must   not   show   any  
signs of wear

, cutting or fraying
and
  they   must   not   be   converted   or  
modified.
The

 
force
 
limiter
 
reduces
 
the
 
pressure
 of the seat belt against the body of the
occupants.
The pretensioning seat belts are active
when
 
the
 
ignition
 
is
 
switched
 
on.
The
 
inertia
 
reels
 
are
 
fitted
 
with
 
a
 
device
 
which

 
automatically
 
locks
 
the
 
strap
 
in
 
the

 
event
 
of
 
a
 
collision
 
or
 
emergency
 
braking

 
or
 
if
 
the
 
vehicle
 
rolls
 
over.
You can unfasten the seat belt by
pressing
 
the
 
red
 
button
 
on
 
the
 
buckle.
 
Guide

 
the
 
seat
 
belt
 
after
 
unfastening.
The
 
airbag
 
warning
 
lamp
 
comes
 
on
 
if

 
the
 
pretensioners
 
are
 
deployed.
 
Contact a CITR

o
Ë
n
dealer or a
qualified
 
workshop.
In
 
order
 
to
 
be
 
effective,
 
a
 
seat
 
belt:
-
 
must

 
restrain
 
one
 
person
 
only,
-
 
must

 
not
 
be
 
twisted,
 
check
 
by
 
pullin

g in front of you with an even
movement,
-
 
must

 
be
 
tightened
 
as
 
close
 
to
 
the
 
body

 
as
 
possible.
The upper part of the seat belt should
be positioned in the hollow of the
shoulder.
The lap part should be placed as low
as
 
possible
 
on
 
the
 
pelvis.
d

o not interchange the seat belt
buckles
 
as
 
they
 
will
 
not
 
fulfil
 
their
 
role
 
properly

.
 
If
 
the
 
seats
 
are
 
fitted
 
with
 
armrests,

 
the
 
lap
 
part
 
of
 
the
 
seat
 
belt
 
should

 
always
 
pass
 
under
 
the
 
armrest.
Check
 
that
 
the
 
seat
 
belt
 
is
 
fastened
 
correctly

 
by
 
pulling
 
the
 
strap
 
firmly.Front seat belts
The front seats are fitted with pretensioners   and   force   limiters.
Rear seat belts
(5 seat version)
The rear seats are fitted with three-
point   inertia   reel   seat   belts.
SaFETY
5
Seat belts

131
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
Curtain airbags
This is a system which protects the driver and passengers (with the
exception of the centre seat of row 2)
in  the   event   of   a   serious   side   impact   in  
order

  to   limit   the   risk   of   head   injuries.
Each curtain airbag is incorporated in
the pillars and the upper part of the
passenger
  compartment.
Activation
It
  is   triggered   at   the   same   time   as   the  
corresponding lateral airbag in the
event

  of   a   serious   side   impact   applied  
to

  all   or   part   of   the   side   impact   zone B,
perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane
  and   directed   from   the   outside  
towards

  the   inside   of   the   vehicle.
The
  curtain   airbag   inflates   between   the  
front or rear occupant of the vehicle
and

  the   windows.
Lateral airbags
This is a system which protects the driver and front passenger in the event
of  a   serious   side   impact   in   order   to   limit  
the

  risk   of   injury   to   the   chest.
Each
  lateral   airbag   is   fitted   in   the   front  
seat

  backrest   frame,   on   the   door   side.
Deployment
It is deployed unilaterally in the event
of
  a   serious   side   impact   applied   to  
all

  or   part   of   the   side   impact   zone B,
perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane
  and   directed   from   the   outside  
towards

  the   inside   of   the   vehicle.
The
  lateral   airbag   inflates   between   the  
front occupant of the vehicle and the
corresponding

  door   trim   panel.Impact detection zones
A.
 Front   impact   zone.
B.  Side   impact   zone.Operating fault
If   this   warning   lamp   comes  
on

  in   the   instrument   panel,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen, contact a CITR

o Ë n
dealer   or   a   qualified   workshop   to   have  
the

  system   checked.  
The
  airbags   may  
no longer be deployed in the event of a
serious

  impact.
In   the   event   of   a   minor   impact   or  
bump

  on   the   side   of   the   vehicle   or  
if the vehicle rolls over

, the airbag
may
  not   be   deployed.
SaFETY
5
airbags

132
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
Front airbags
Deployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement. Deactivating the passengers front
airbag
o

nly the passenger's front airbag can
be   deactivated.
-
W
ith the ignition switched off,
insert   the   key   into   the   passenger's  front
  airbag   deactivation   switch.
- T urn it to the "OFF"   position.
-
 
Remove
  the   key   keeping   the   switch  
in

  the   new   position.
The passenger's front airbag
warning
 
lamp
 
in
 
the
 
instrument panel

  remains   on   while   the
 airbag

  is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rearward facing child seat and
contact a CITR
o Ë n dealer or a
qualified
  workshop.
Front airbag fault
To ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rearward facing child seat on
the
  front   passenger   seat.   Otherwise,  
the

  child   would   risk   being   killed   or  
seriously

  injured   if   the   airbag   were  
deployed.Reactivation
In the

"OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the passenger's front airbag switch
to the

"ON" position to reactivate the
airbag and thus ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  
on,

  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, consult a
CITR

o Ë n dealer or a
qualified   workshop   to   have  the
  system   checked.
The
  front   airbags   are   fitted   in   the  
centre of the steering wheel for the
driver and in the dashboard for the
front

  passenger.
airbags

136
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
DEACTIVATING THE
P
ASSENGER ' S
FRONT
AIRBAG
never install a rearward facing
child   restraint   system   on   a   seat  
protected

 
by
 
an
 
active
 
front
 
airbag.
 
This could cause the death of the child
or

 
serious   injury.
The warning label present on both
sides of the passenger's sun visor
repeats
  this   advice.   In   line   with   current  
legislation, the following tables contain
this warning in all of the languages
required. For

  information   on   deactivating  the passenger's front airbag, refer
to the "
a irbags" section in this
chapter.
Child safety

 149
Towing a trailer
Berlingo-2-VP_en_Chap06_Accessoire_ed02-2015
Good Practice
In certain cases of particularly arduous
use  (towing   the   maximum   load   up   a  
steep

  slope   in   high   temperatures),   the  
engine

  automatically   limits   its   power.  
In this case, the air conditioning is
automatically

  cut   off   to   save   engine  
power

.
Tyres
Check
  the   tyre   pressures   of   the   towing  
vehicle and of the trailer

, observing the
recommended
  pressures.
Chapter
  7,   "Levels"   section.
If
  the   coolant   temperature  
warning

  lamp   comes   on,   stop  
the vehicle and switch of

f the
engine
  as   soon   as   possible.Brakes
Towing
  increases   the   braking   distance.  Drive
  at   a   moderate   speed,   change  
down

  early   and   brake   gradually.
Towbar
We recommend the use of genuine CITRo Ë n towbars and their wiring
harnesses, which have been tested
and
  approved   from   the   design   stage   of  
your vehicle, and that you entrust the
fitting

  of   this   equipment   to   a   CITROËN  
dealer

.
If
  this   equipment   is   not   fitted   by   a  
CITROËN

  dealer,   it   is   imperative   that  
it

  is   fitted   using   the   electrical   pre-
equipment
  installed   at   the   rear   of   the  
vehicle and in accordance with the
manufacturer's

  instructions.
In accordance with the general
instructions
  a   reminder   of   which   has  
been given above, we draw your
attention

  to   the   risk   associated   with  
fitting

  a   towbar   or   electrical   accessory  
not

  recommended   by   CITROËN.  
Fitting

  such   equipment   could   result   in  
the failure of your vehicle's electronic
system.

  Please   obtain   information   from  
the

  Manufacturer   before   fitting   this   type  
of

  equipment.
Side wind
Sensitivity
 
to
 
side
 
wind
 
is
 
increased.
 
Drive

 
smoothly
 
and
 
at
 
a
 
moderate
 
speed.
ABS/DSC
The

 
ABS

 
or
 
DSC
 
systems
 
only
 
control
 
the

 
vehicle,
 
not
 
the
 
trailer
 
or
 
caravan.
Parking sensors
The
 
rear
 
parking
 
sensors
 
system
 
does
 
not

 
function
 
while
 
the
 
vehicle
 
is
 
towing.
Chapter
 
9,
 
"Identification
 
markings"

 
section.
ACCESSORIES
6