CITROEN C CROSSER DAG 2009 Owners Manual

P R A C T I C A L I N F O R M A T I O N
IX
129
CHANGING A BULB
Handle the bulbs using a dry
cloth.

Do not clean the headlamps
using a dry or abrasive cloth, or us-
ing detergent or solvent products,

use a sponge and soapy water. In certain climatic conditions
(low temperature, humidity),
t
he
presence of condensation on the
inside of the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on.
Front lights
Blown bulb
Refer to the appropriate procedure to
change the corresponding bulb.
1. Direction indicators
(PY21W - 21 W).
2. Dipped headlamps (H11 - 55 W) or xenon bulb (D2S - 35 W).
3. Side lights (W5W - 5 W).
4. Main beam headlamps (H7 - 55 W).
5. Front fog lamps (H11 - 55 W). WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
CITROËN dealer.
Operating procedure for replacing a
faulty bulb with a new bulb.

P R A C T I C A L I N F O R M A T I O N
IX
130
Changing the direction
indicators (1) Coloured bulbs must be replaced
with bulbs of identical specifi cation
and colour.

 Turn the bulb holder A to the left
and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order. Access to the bulbs
on the left-hand side
When you change a bulb on the left-
hand side, remove the relay box fi xing
nut
B and move the relay box towards
the rear. Access to the bulbs
on the right-hand side
When you change a bulb on the right-
hand side:

 Remove the screenwash reservoir
fi xing C and move the reservoir
towards the rear.

 Remove the coolant reservoir fi xing
nut D .

 Remove the clip E and raise the
reservoir moving it towards the
front.

P R A C T I C A L I N F O R M A T I O N
IX
131
Changing the side lights (3)

 Unscrew the cover H .

 Disconnect the connector.

 Turn the bulb holder I a quarter of a
turn and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.

 Unscrew the cover F .

 Disconnect the connector.

 Turn the bulb G to the left and re-
move it.
To refi t, carry out these operations in
reverse order.
Changing the dipped headlamps (2)
Changing the main beam
headlamps (4)

 Unscrew the cover J .

 Disconnect the connector.

 Move aside the spring K to release
the bulb and remove it.
To refi t, carry out these operations in
reverse order.

P R A C T I C A L I N F O R M A T I O N
IX
132
Changing the integrated direction
indicator side repeaters

 Push the repeater A towards the
rear and detach it.

 Unclip the repeater.

 Disconnect the repeater connector
and change the repeater.
To refi t, carry out these operations in
reverse order.
To obtain repeaters, contact a CITROËN
dealer. Changing the fog lamps (5)

 Turn the wheel fully towards the out-
side for easy access to the fl ap A
located in the wheelarch.
 Using a screwdriver, remove the four
clips B located in the wheelarch.

P R A C T I C A L I N F O R M A T I O N
IX
133

 Using a screwdriver, remove the
three clips C located below the
bumper.
 Lift the access fl ap D located in the
wheelarch and slide it downwards.
 Disconnect the connector E .

 Turn the bulb F to the left and
remove it.
To refi t, carry out these operations in
reverse order.

P R A C T I C A L I N F O R M A T I O N
IX
134
Rear lights

1.
Third brake light (diodes).

2.
Brake lights / Side lights
(21/5 - W21W - 5 W).

3.
Direction indicators
(WY21W - 21 W).

4.
Reversing lights (W21W - 21 W).

5.
Number plate lights (W5W - 5W).

6.
Fog lamps (W21W - 21 W). Changing the brake lights / side
lights and direction indicators
These two bulbs are changed from
outside with the tailgate open:

 Open the tailgate (refer to the
“Access” section),

 Remove the two light fi xing bolts A ,

 Extract the light from outside,
 Turn the pin C to the left and remove it.

 Pull the bulb D and change it .
To refi t, carry out these operations in
reverse order.

 Turn the pin B to the left and remove it.

 Pull the bulb and change it. When refi tting the light, align the
two pins
E with the openings on the
vehicle.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour.
Changing the third brake light
(diodes)
All work on the diode lights must be
carried out by a CITROËN dealer.

P R A C T I C A L I N F O R M A T I O N
IX
135
Changing the reversing lights

 Open the tailgate (refer to the
“Access” section),

 From the inside of the tailgate, in-
sert a screwdriver in the opening on
the cover A to use it as a lever to
open the cover. Changing the number plate lights

 Open the tailgate (refer to the
“Access” section) to gain access to
the number plate lights D ,

 Remove the light unit D while
pressing it to the left.

 Turn the pin B to the left and remove
it.
 Pull the bulb C and change it.
To refi t, carry out these operations in
reverse order.
 Insert a thin screwdriver in the ope-
ning on the lens to press the tab E .

 Remove the lens.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.

 To refi t the light unit, insert the end
of the tab F fi rst, then align the
tab G .

P R A C T I C A L I N F O R M A T I O N
136
Changing the fog lamps

 Open the tailgate and the lower tail-
gate (refer to the “Access” section)
and fold down the cover A .

 Remove the 4 clips B using a
screwdriver to detach the light
cover.

 Remove the bolts C and remove the
light unit.
 Turn the pin and bulb assembly D to
the left.

 Remove the bulb.
To refi t, carry out these operations in
reverse order.

 When refi tting the light unit, align
the clips E with the openings on the
bodywork.

P R A C T I C A L I N F O R M A T I O N
137
INTERIOR BULBS
Front and rear courtesy lights

 Insert a screwdriver to remove the courtesy light cover.

 Remove the bulb while pressing the tab A .
To refi t the cover, align the hooks on the holes located in the body of the vehicle. Glove box light

 Turn the pin B anticlockwise and re-
move it.

 Remove the bulb.
Low level light

 Insert a screwdriver to remove the
light cover.

 Remove the bulb.

P R A C T I C A L I N F O R M A T I O N
IX
138
CHANGING A FUSE
Access to the tools
The extraction pliers are installed in the
engine compartment fuse box.
To gain access to them:

 Open the bonnet (refer to the
“Access” section),

 Press on the hook A and release the
catch,

 Remove the cover completely,

 Remove the pliers B . CITROËN will not accept re-
sponsibility for the cost incurred
in repairing your vehicle or for
rectifying the malfunctions resulting
from the installation of accessories
not supplied and not recommended
by CITROËN and not installed in ac-
cordance with its instructions, in par-
ticular when the consumption of all of
the additional equipment connected
exceeds 10 milliamperes. Your vehicle’s electrical system is
designed to operate with standard
or optional equipment.
Before installing other electrical
equipment or accessories in your
vehicle, contact a CITROËN dealer.
Changing a fuse
Before changing a fuse, the cause of the
failure must be identifi ed and rectifi ed.

 Identify the faulty fuse by checking
the condition of its fi lament.

 Use the special pliers to extract the
fuse from its location.

 Always replace the faulty fuse with
a fuse of the same rating.

 Check the correspondence between
the number etched on the box, the
rating etched on the top and the
tables below. Correct
Incorrect
The spare fuses are located on the
engine compartment fuse box cover.
Operating procedure for replacing a
faulty fuse with a new fuse to rectify a
failure in the corresponding function.