ignition Citroen C ZERO 2015 1.G User Guide

35
C-zero_en_Chap03_confort_ed01-2014
Mirrors
Adjustment
The mirrors can be adjusted when the ignition
switch is in the "ON" or "ACC" position.
F
Mov
e control A to the right or to the left to
select the corresponding mirror.
F


d
ir
ect control B in all four directions to
adjust the mirror.
When adjustment is complete, return control A
to the central position.
Door mirrors
The mirrors can also be folded
manually.
However, you must never unfold them
manually , other wise the mirrors may
not remain in place correctly when
driving.
alw

ays use control C to unfold them.
Electric folding / unfolding*
F With the ignition switch in the "ON" or
" ACC" position: press control C to unfold
them
F
Wi

th the ignition switch in the "LOCK"
position: press control C within
30
s

econds to fold them.
* Depending on version.
3
Comfort

47
C-zero_en_Chap04_conduite_ed01-2014
Starting - stopping the vehicle
- Position 1: LOCK The steering is locked.
-
Po

sition 2: ACC
Th

e ancillaries (radio, 12 V socket...) can
be used.
-
Po

sition 3: ON
Ig

nition on.
-
Po

sition 4: S TA R T
"R

eady" lamp on.
Mo

tor ready to drive the vehicle.
Ignition switch
F Check that the drive selector is in
position P.
F In

sert the key in the ignition switch.
F
Tu

rn the key to position 4 (S TA R T ) .
Starting Stopping
F Stop the vehicle.
F Ke ep your foot on the brake pedal.
F
Pl

ace the drive selector in position P .
F
Ap

ply the parking brake.
F
Tu

rn the key to position 1 (LOCK) .
F
Re

move the key from the ignition switch.
F
Ho

ld it in this position for a few
seconds until the " RE ADY " lamp
comes on accompanied by an
audible signal.
F
Re

lease the key.
Th

e key returns automatically to position 3
(ON) . Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
If you use the ancillaries for a prolonged
period (with the key in the ACC position),
you risk discharging the ancillaries
battery. Starting your vehicle will then no
longer be possible. Be aware .
4
Driving

48
C-zero_en_Chap04_conduite_ed01-2014
Parking brake
Applying
F Pull the parking brake lever fully up to
immobilise your vehicle.
When parking on a slope, direct your
wheels against the kerb, apply the
parking brake, place the drive selector
in position P and switch off the ignition.
Releasing
F Pull the parking brake lever up slightly,
press the release button then lower the
lever fully.
When the vehicle is being driven, if
the parking brake is still on or has
not been fully released, this warning
lamp comes on.
Driving

50
C-zero_en_Chap04_conduite_ed01-2014
To tow your vehicle, the drive selector
must be in position N, refer to "Practical
Information".
Parking the vehicle
To stop the motor, you must select position P .
You must apply the parking brake to immobilise
the vehicle.
To remove the key from the ignition switch, the
drive selector must be in position P .
Driving

52
C-zero_en_Chap05_visibilite_ed01-2014
Front and rear foglamps
Foglamps selection ring.
The foglamps operate with the sidelamps and
dipped and main beam headlamps.Front and rear foglamps.
In good or rainy weather, both day
and night, the front foglamps and the
rear foglamp is prohibited. In these
situations, the power of its beam may
dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when
they are no longer necessary.
Lighting on reminder
There is an audible signal when the
driver's door is opened, to warn the
driver if the vehicle lighting is on, with
the ignition off.
Switching off the lighting stops the
audible signal.
F
To s

witch on the front foglamps, turn the
ring for wards once.
F
To s

witch on the rear foglamp, turn the ring
for wards twice.
F
To s

witch off the rear foglamp, turn the ring
rear wards twice.
F
To s

witch off the front foglamps, turn the
ring rear wards once.
The ring returns to its initial position automatically.The rear foglamp is switched off automatically
when you switch off the sidelamps, or the
dipped or main beam headlamps.
Visibility

53
C-zero_en_Chap05_visibilite_ed01-2014
Daytime running lamps
Special daytime lighting so that the vehicle can
be seen more easily.
The daytime running lamps come on
automatically when starting the motor, if no
other lighting is on.
They cannot be deactivated.Automatic illumination of headlamps
With the main lighting control ring in the AUTO
position, the sidelamps and dipped beam headlamps
come on automatically, without any action by the
driver, when a low level of ambient light is detected.
When the light returns to a sufficient level or the
wipers are switched off, the lighting is switched off
automatically.
The sensor is located at the base of the windscreen.
Automatic illumination of
headlamps
Automatic lighting off
When the lighting stalk is in the
"AUTO" p osition, if the ignition switch is in
the "LOCK" or "ACC" position or if the key
has been removed, the lighting switches off
automatically when the driver's door is
opened . The initial setting is position "0"
.
Headlamp
adjustment
To avoid causing a nuisance to other road
users, the height of the halogen headlamps
should be adjusted according to the load in
the
v

ehicle.
0.
Dr

iver only or driver + 1 front passenger.
1 or 2.
4 pe

ople (including the driver).
3.
4 pe

ople (including the driver) + maximum
authorised load.
4.
Dr

iver + maximum authorised load.
Although these lamps are located in
the same unit as the front foglamp, they
operate with a specific bulb.
Their use is covered by road vehicle
lighting regulations.
In foggy weather or in snow, the
sunshine sensor may detect sufficient
light. The lighting will not come on
automatically.
do no

t cover the sunshine sensor, the
associated functions will no longer be
controlled.
5
Visibility

56
C-zero_en_Chap06_securite_ed01-2014
Direction indicators
Selection of the left or right direction indicators
to signal a change of direction of the vehicle.
F
Le
ft: lower the lighting stalk beyond the
point of resistance.
F
Ri

ght: raise the lighting stalk beyond the
point of resistance.
Automatic operation
of brake lamps
The brake lamps come on automatically when
you release the accelerator pedal.
This does not happen in all cases and depends
on the rate of deceleration.
Hazard warning lamps
A visual warning by means of the direction
indicators to alert other road users to a vehicle
breakdown, towing or accident.
F
Pr

ess this button, the direction indicators
flash.
They can operate with the ignition off.
S

58
C-zero_en_Chap06_securite_ed01-2014
Under-inflation detection
System which continuously and automatically
checks the pressures of the four tyres after
switching on the ignition.
A pressure sensor is located in the valve of
each tyre.
The system triggers an alert if a drop in
pressure is detected in one or more tyres,
compared to the reference pressure registered
in the system. This reference pressure must be
reinitialised every time the tyre pressures are
adjusted or a wheel changed.
The system operates on condition that sensor
identifiers have first been memorised in the
system by a CITROËN dealer or a qualified
workshop.
You can memorise two sets of tyres
(for example: wheels with "standard" tyres and
wheels with "winter" tyres).The tyre under-inflation detection
system is an aid to driving which does
not replace the need for vigilance on
the part of the driver. This system does not avoid the need to
check the tyre pressures regularly and
before a long journey.
Driving with under-inflated tyres
adversely affects road holding,
extends braking distances and causes
premature tyre wear, particularly under
arduous conditions (vehicle loaded,
high speed, long journey).
Driving with under-inflated tyres
increases fuel consumption. The tyre pressures for your vehicle can
be found on the tyre pressure label (see
the "Identification markings" section).
The tyre pressures must be checked
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6 miles (10 km) at moderate speed).
Other wise, add 0.3 bar to the values
indicated on the label.
Safety

60
C-zero_en_Chap06_securite_ed01-2014
The under-inflation alert is only reliable
if the system has been reinitialised
with the four tyre pressures correctly
adjusted.Go to a CITROËN dealer or a qualified
workshop
t

o have the system checked
or, following the repair of a puncture, to
have the original wheel, equipped with a
sensor, refitted.
The reinitialisation instruction is entered in
the instrument panel screen screen, with the
ignition on and the vehicle stationary.
F
Pr

ess button A select the function
F
Pr

ess and hold button A for at least
3
s
econds
to reinitialise the under-inflation
detection system.
Reinitialisation of the system is confirmed
by the flashing of the warning lamp in the
instrument panel.
You then have to drive about 100 metres before
the warning lamp goes off.
Operating fault
The flashing and then fixed illumination
of the under-inflation warning lamp
indicates a fault with the system.
In this case, monitoring of the tyre pressures is
not assured.
This alert is also displayed if:
-
on

e or more wheels is not fitted with a
sensor,
-
a wi

reless device operating on the same
frequency is close to the vehicle,
-
th

ere are accumulations of snow or ice in
the wings or wheels,
-
th

e state of charge of the tyre pressure
monitoring system battery is too low,
-
th

e wheel sensor identifiers have not been
memorised in the system by a CITROËN
dealer or a qualified workshop. Any tyre repair or replacement on a
wheel fitted with this system must be
carried out by a CITROËN dealer or a
qualified workshop.
If you fit the second set of tyres
memorised in the system, a fault will
be signalled until the second set is
selected in the configuration menu.
Safety

61
C-zero_en_Chap06_securite_ed01-2014
Managing sets of wheels
and tyres
Selection of the other set of wheels and tyres
is is done via the instrument panel screen, with
the ignition on and the vehicle stationary.
After fitting the new set of wheels and
tyres, you should check and adjust the
tyre pressures to the values specified
on the tyre pressure label (see the
"Identification markings" section). The system automatically reinitialises
the reference pressure based on the
pressure in the new set (the under-
inflation detection warning lamp flashes
during the operation).
If you have had a second set of wheels and
tyres registered by a CITROËN dealer or a
qualified workshop, every time you change the
set of wheels (fitting a set of winter tyres, for
example), you must select the set you have just
fitted in the configuration menu.
F
Pr

ess button A to select the function.
F
Pr

ess and hold button A button for more
than 10 seconds to change successively
from set of wheels and tyres 1 to set of
wheels and tyres 2 or the other way round.
6
Safety