spare wheel Citroen C1 DAG 2008 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C1 DAG, Model: Citroen C1 DAG 2008 1.GPages: 97, PDF Size: 3.15 MB
Page 52 of 97
4
50
ACCESS
BOOT
2. Spare wheel/Additional storage compartments
Located under the carpet and a plas-
tic cover, this contains the tools for
wheel changing and towing.
There are two shelf storage options:
- either behind the rear seats,
- o r fl a t i n t h e b o o t .
1. Rear shelf
To remove the shelf:
- u n h o o k t h e s h e l f f r o m i t s fi x i n g
A ,
- pull upwards on each side to de- t a c h i t f r o m i t s fi x i n g s ,
- raise then tilt the shelf slightly to remove it. In order to obtain additional
space, the spare wheel can be
removed temporarily (boot tray
available as an accessory).
Page 74 of 97
9
69
PRACTICAL INFORMATION
Parking the vehicle
As far as possible, immobilise the
vehicle on level, stable, non-slip-
pery ground.
Apply the handbrake, switch
o f f t h e i g n i t i o n a n d e n g a g e fi r s t
gear, reverse or position N for the
"SensoDrive" gearbox. Tools
The following tools are installed in a
carrier, located in the centre of the
spare wheel:
1. Wheelbrace
2. Jack with handle
3. Removable towing eye
Access to the spare wheel and
the jack in the boot
Remove the carpet then the plas-
tic cover using the handle. Tyre pressure
This is indicated on the label posi-
tioned on the interior pillar of the left
d o o r , s e e " I d e n t i fi c a t i o n " .
CHANGING A WHEEL
If necessary, chock the wheel di-
agonally opposite the wheel to be
changed.
It is imperative that you ensure
that the occupants get out of the
vehicle and wait in a safe loca-
tion.
Page 75 of 97
9
70
PRACTICAL INFORMATION R e fi t t i n g t h e w h e e l
1. Position the wheel.
2. Screw in the bolts fully by hand.
Removing the wheel
1. Remove the trim.
2. Release the wheel bolts using the
wheelbrace 1 .
3. Place the jack 2 in contact with
one of the four locations A pro-
vided on the underframe, the
one closest to the wheel to be
changed.
4. Extend the jack 2 until its base
is in contact with the ground. En-
sure that the centreline of the jack
base is directly below the location
A used.
5. Lift the vehicle.
6. Remove the bolts and detach the
wheel.
3. Pre-tighten * using the wheel-
brace 1 .
* I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y w h e e l s , w h e n t i g h t e n i n g t h e b o l t s i t i s normal
to notice that the washers do not come into contact with t he spare wheel. It is
fi x e d s e c u r e l y .
Page 76 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quar-
ter of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
tact a CITROËN dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a CITROËN dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps
Page 77 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quar-
ter of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
tact a CITROËN dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a CITROËN dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps
Page 90 of 97
9
81
PRACTICAL INFORMATION
TOWING YOUR VEHICLE
Your vehicle can only be towed at
the front. Lifting (2 wheels only on the
road)
It is preferable to raise the vehicle by
the wheels.
Never use the radiator crossmember.
When your vehicle is be-
ing towed with the engine
switched off, there is no brak-
ing or steering assistance.
Without lifting
(4 wheels on the road)
You should always use a towbar.
The removable towing eye is stored
in the spare wheel, under the boot
carpet.
Unclip the bottom of the cover,
Screw in the towing eye until it
locks.
Place the gear lever in posi-
tion N for the "SensoDrive"
gearbox.
FITTING ROOF BARS
W h e n fi t t i n g t r a n s v e r s e r o o f b a r s ,
use the accessories recommended
by CITROËN and follow the manu-
f a c t u r e r ’ s fi t t i n g i n s t r u c t i o n s .
For further information, contact a
CITROËN dealer.
Please refer to national legis-
lation in order to comply with
the regulations concerning the
transportation of objects which
are longer than the vehicle.
Towing with fours wheels on the road
must be carried out at very low speed
over a very short distance (in accor-
dance with the legislation in force).
In all other cases, your vehicle must
be transported on a trailer.
Vehicles fitted with a manual
gearbox (diesel version)
I n t h e c a s e o f v e h i c l e s fi t t e d w i t h a
manual gearbox, the gear lever must
be in the neutral position.
Failure to observe this special condi-
tion may result in damage to certain
braking components and the ab-
sence of braking assistance the next
time the engine is started.
Maximum weight authorised on
the bars, for a loading height not
exceeding 40 cm (except bicycle
carrier): 50 kg.
If the height exceeds 40 cm, adapt
the speed of the vehicle to the pro-
fi l e o f t h e r o a d t o a v o i d d a m a g i n g
the roof bars.