Ati Citroen C2 2004 1.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 111
ENGINE
XSARA
CYLINDER HEAD
Identification of cylinder head gasket
Number
of holes
at B Number
of holes
at A Thickness
(mm)
± 0,04 Plaque
EnginePiston
standproud
(mm)(
*)
0,51 to 0,55 1,26 1
0,55 to 0,59 1,30 2
0,59 to 0,63 1,34 3
0,63 to 0,67 1,38 4
0,67 to 0,711,425
WJY
(A) = Repère engine.
(B) = Thickness references.
(*) = Take the highest piston as a reference.
B1DP14QD
Engine: WJY
WJY
2

Downloaded from www.Manualslib.com manuals search engine 112
ENGINEXSARA XSARA PICASSOCYLINDER HEAD
Identification of cylinder head gasket
No. of notches at A Thickness
(mm) Plaque
EnginePiston
standproud
(mm)
0,47 to 0,6051,30 ± 0,06 1
0,605 to 0,655 1,35 ± 0,06 2
0,655 to 0,7051,40 ±0,063
0,705 to 0,755 1,45 ± 0,06 4
0,755 to 0,83 1,50 ± 0,06 5
RHY
RHZ
B1DP15AD
Engines: RHY RHZ

Downloaded from www.Manualslib.com manuals search engine 120
ENGINE
B1BP234C
XSARA PICASSOAUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
Without air conditioning.
Tools.
[1]Pliers for removing plastic pegs: 7504 –T
[2]Belt tension measuring instrument: 4122 –T
[3]TORX spanner
Remove. Release the central screw (1),tool [3] Detension the tensioner roller (2), (flat spanner 27 on flat).
Remove the belt.
Refit. Position the belt.
Hold the belt in position using the tensioner roller (2).
Pretension the belt 120 SEEM units, tool [2].
Lock the central screw (1),tool [3].
Remove the tool [2].
Rotate the crankshaft 2to 4times.
Check the tension, 120 SEEM units.
If not, restart the operation.

Downloaded from www.Manualslib.com manuals search engine 121
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
With air conditioning.
XSARA PICASSO
B1BP235C
Tools.
[1]
Pliers for removing plastic pegs: 7504 –T
[2] Belt tension measuring instrument: 4122 –T
[3] 10 mm square (drain spanner)[4] TORX spanner
Remove. Detension the automatic tensioner, tool[3]. Place aØ 6 mm peg at(a) to immobilise the automatic tensioner.
Remove the belt.
Refit. Position the belt
Detension the automatic tensioner, tool[3]. Remove theØ 6 mm peg.
Release the automatic tensioner.
Remove the tool
[3].

Downloaded from www.Manualslib.com manuals search engine 127
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT 2002XSARA
Tools.
[1]
Belt tension measuring instrument :4122T
(1)
Tensioning screw.
(2)Roller support fixing screw (3).
Lightly tighten the screws
(2).
Place the tool
[1]on the belt.
Tension the belt using the screw
(1).
• Reused belt
90 SEEM units.
• New belt
120 SEEM units.
Tighten the screws
(2)to 2 m.daN.
Remove the tool
[1].
Rotate the crankshaft by 3 turns
(direction of rotation).
Check the belt tension using the tool
[1], and adjust (if necessary).
Without air conditioning.
B1EP12YCB1EP12XC
Engine: RFS

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
With compressor and alternator .
B1BP2MKCB1BP2MJD
Tools.
[1]
Pliers for removing plastic pegs: 7504T
[2]Tensioner roller compression lever:().0194.E
[3]Tensioner roller setting peg Ø4 mm: ().0194.F
Removing.
Disconnect the battery negative cable.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel.
Move aside the splashshield, using tool
[1].
IMPERATIVE: In the case of belt reuse, mark the
direction of rotation of the belt. If the index on the
tensioner roller is outside the marks, change
the auxiliary equipment drive belt.
The alternator (1).
The aircon compressor (2).
Detension the auxiliary belt tensioner roller, using tool [2].
Position the peg [3].
Remove the auxiliary drive belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 137
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Tools.
[1]
Dynamic tensioner compression lever: ().0188.Z
[2]Peg for dynamic tensioner roller: ().0194.F
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to high pressure
diesel injection engines (HDi).
Remove:
The front RH wheel.
The underengine sounddeadening.
The splashshield.
WARNING: Mark the direction of fitting of the accessories drive belt, if it is to be reused.
Compress the tensioner roller (1)by acting at «a»(clockwise), using tool [1].
Peg at «b», using tool [2].
Keeping the tensioner roller (1)compressed, remove the accessories drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely (without play and without
tight spots).B1BP2VZD
Engine: 8HZ

Downloaded from www.Manualslib.com manuals search engine 138
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Refitting.
WARNING:
Belt to be reused, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller
(1)by acting at «a»(clockwise), using tool [1].
Remove tool
[2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various
pulleys.
Complete the refitting in the opposite order to removal.
Engine: 8HZ
B1BP2VZD

Downloaded from www.Manualslib.com manuals search engine 139
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HY 8HV
B1BP2MYDB1BP2MZC
Tools.
[1a]
Dynamic tensioner roller lever: ().0194E1
[1b]Lever extension: ().0194E2
[2]Accessories belt roller locking peg Ø 4 mm: ().0194F
Removing.
Pivot the tensioner roller support (1)(clockwise), using tools [1a]and [1b]at «a».
Remove the belt.
Immobilise the support
(1)of the tensioner roller, using tool [2].
Remove the auxiliary drive belt (2).
IMPERATIVE: Ensure that the tensioner rollers turn freely (no play, no tight spot).
Refitting.
Refit the belt.
Move the tool [1]on the tensioner roller to remove the peg [2].
ESSENTIAL: Make sure that the belt is correctly positioned in the various pulley
grooves.
C3

Downloaded from www.Manualslib.com manuals search engine 140
ENGINE
140
B1BP2Z6DB1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ 9HY
Tools.
[1]
Dynamic tensioner compression lever: ().0188.Z
[2]Peg for dynamic tensioner roller: ().0194.F
Removing.
Remove the front RH wheel, the underengine sounddeadening and the splashshield.
Vehicle with air conditioning.WARNING:Mark the direction of fitting of the accessories drive belt, if it is to be reused.
Compress the tensioner roller (1)by acting at «a»(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE:Check that the rollers (1) and (2) can turn freely (without play and without tight spots).
Refitting.
WARNING:
Belt to be reused, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller
(1)by acting at «a»(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO