ignition CITROEN C3 2023 Owner's Manual

50
In the event of a breakdown
Version 2
Fuses
Fuse No.ColourRating (A) Functions
FF01 Red 10On-board diagnosis (OBD-II)
FF02 Yellow 20Body control and cluster module 1 (BCCM-1)
FF03 Green 30Body control and cluster module 2 (BCCM-2)
FF04 Yellow 20Body control and cluster module 3 (BCCM-3)
FF05 Green 30Body control and cluster module 4 (BCCM-4)
FF06 Blue 15Audio system
FF07 Blue 1512V Socket
FF08 Ta n 5Spare connector / USB
FF09 Red 10Front washer
FF10 Ta n 5ECU's ignition
FF11 Ta n 5Airbag ECU
FF12 Ta n 5Switches ignition
FF Ta n 5Service
FF Red 10Service
FF Blue 15Service
FS01 Pink 30Body control and cluster module 5 (BCCM-5)
FS02 Pink 30Body control and cluster module 6 (BCCM-6)

51
In the event of a breakdown
8Relays
RelayColourRating (A) Functions
MICRO Brown 20Ignition Loads
Engine compartment fuses
The fusebox is placed in the engine
compartment near the battery.
Access to the fuses

► Remove the cover.
► Change the fuse.
►

When you have finished, close the cover
carefully then engage the two latches, to ensure
correct sealing of the fusebox.
Version 1
Engine fuse cum relay box
Fuse No. ColourRating (A) Functions
FF01 Green 30ABS ECU
FF02 Red 10HVAC Compressor
FF03 Red 10Horn
FF04 Green 30ECM Loads (Ignition Coil / Injectors / Fuel Pump)
FF05 Blue 15ECM Loads (Canister Valve / O2 Sensors)
FF06 Ta n 5ECM Loads (VVT Valve)

53
In the event of a breakdown
8Fuse No.ColourRating (A) Functions
FF03 Red 10Horn
FF04 Green 30ECM Loads (Ignition Coil
/ Injectors / Fuel Pump)
FF05 Blue 15ECM Loads (Canister Valve
/ O2 Sensors)
FF06 Ta n 5ECM Loads (VVT Valve)
FF07 Yellow 20ECM Power Supply
FF08 Ta n 5Radiator Fan Relay Coil Supply
FS01 Black 80Cabin Fuse Box Loads (CFB-1)
FS02 Yellow 60Electric Power Steering (EPS) Motor
FS03 Green 40ABS Motor
FS04 Green 40Radiator Fan
FS05 Green 40Accessory Load (HVAC Blower/Washer)
FF Green 30Service
FF Blue 15Service
FF Red 10Service
Relay ColourRating (A) Functions
MICRO Brown 20HVAC Compressor
MICRO Brown 20Horn
MICRO Brown 20Starter Solenoid
MICRO Grey 35ECM Main

54
In the event of a breakdown
Engine fuse cum relay box turbo
Fuse No.ColourRating (A) Functions
FF01 Green 30ABS ECU
FF02 Red 10HVAC Compressor
FF03 Red 10Horn
FF04 Green 30ECM Loads (Ignition Coil
/ Fuel Pump)
FF05 Blue 15ECM Loads (Canister Valve
/ O2 Sensors)
FF06 Blue 15ECM Loads (VVT


/ Thermostat / Oil Pump Valve)
FF07 Yellow 20ECM Power Supply & Injectors
FF08 Ta n 5Radiator Fan Relay Coil Supply
FS01 Black 80Cabin Fuse Box Loads (CFB-1)
FS02 Yellow 60Electric Power Steering (EPS) Motor
FS03 Green 40ABS Motor
FS04 Yellow 60Radiator Fan
FS05 Green 40Accessory Load (HVAC Blower/Washer)
FF Green 30Service
FF Blue 15Service
FF Red 10Service
Relay ColourRating (A) Functions
MICRO Brown 20HVAC Compressor
MICRO Brown 20Horn
MICRO Brown 20Starter Solenoid
MICRO Grey 35ECM Main

57
In the event of a breakdown
8at least equal to that of the discharged
battery.
The two vehicles must not be in contact with
each other.
Switch off all electricity-consuming equipment
on both vehicles (audio system, wipers,
lighting, etc.).
Make sure that the jump leads are well away
from the engine’s moving parts (fan, belt,
etc.).
Do not disconnect the (+) terminal while the
engine is running.
During jump start, extra care should be taken
to ensure right terminals are connected. If
terminal connections are reversed, it will
lead to failure of alternator & other electrical,
electronic components.
Never power electrical or electronic
components directly from battery terminals
as it will lead to poor battery charging, poor
performance of components and battery
sensor malfunction, which will impact fuel
economy. For Naturally Aspirated engine version

► Lift the cover on the (+) terminal, if the vehicle
has one.
►
Connect the red cable to the (+) terminal
of flat battery

A, then to the (+) terminal of the
backup battery
B or of the booster.
►

Connect one end of the green or black cable
to the (-) terminal of the backup battery

B or of
the booster (or to an earth point on the assisting
vehicle).
►

Connect the other end of the green or black
cable to the (-) terminal of flat battery

A.
►

Start the engine on the assisting vehicle and
leave it running for a few minutes.
►


Operate the starter on the broken down
vehicle and let the engine run.
If the engine does not start immediately

, switch
off the ignition and wait a few moments before
trying again.
►

W
ait for it to return to idle.
►

Disconnect the jump leads in reverse order:
first remove (-) terminal then (+) terminal.
► Refit the cover to the (+) terminal, if the
vehicle has one.
►

Allow the engine to run for at least
30

minutes, with the vehicle stationary, so that
the battery reaches an adequate state of charge.
For Turbo engine version

The negative cable must be connected to the car ground (not to the battery
negative terminal) so that the battery sensor
can detect all charging and discharging
currents.
►

Lift
the cover on the (+) terminal, if the vehicle
has one.
►

Connect the red cable to the (+) terminal of
flat battery

A (at the metal elbow), then to the
(+) terminal of the backup battery
B or of the
booster.
►

Connect one end of the green or black cable
to the (-) terminal of the backup battery

B or of

58
In the event of a breakdown
the booster (or to an earth point on the assisting
vehicle).
►
Connect the other end of the green or black
cable to the earth point


C
on the broken down
vehicle.
►

Start the engine on the assisting vehicle and
leave it running for a few minutes.
►


Operate the starter on the broken down
vehicle and let the engine run.
If the engine does not start immediately

, switch
off the ignition and wait a few moments before
trying again.
►

W
ait for it to return to idle.
►

Disconnect the jump leads in reverse order:
first remove (-) terminal then (+) terminal..
►


Refit the cover to the (+) terminal, if the
vehicle has one.
►


Allow the engine to run for at least
30

minutes, with the vehicle stationary, so that
the battery reaches an adequate state of charge.
Driving immediately without having
reached a sufficient level of charge may
affect some of the vehicle's functionalities.
Disconnecting/removing the
battery
In order to maintain an adequate state of charge
for starting the engine, it is recommended that
the battery be disconnected if the vehicle is
taken out of service for a long period.
Before disconnecting the battery: ►

Close all openings (doors, boot, windows).
►

Switch off all electrical consumers (audio
system, wipers, lighting, etc.).
►

Switch off the ignition and wait for 4
minutes.


Naturally Aspirated engine version

Turbo engine version
►
Disconnect the negative cable.
►

Disconnect the positive cable.
► Remove the mounting bracket if you need to
remove the battery .
Be careful not to cause accidental short
circuits between the positive and
negative battery terminals.
Do not allow smoking, sparks or flames
around fuel or the battery.
After reconnection
After reconnecting the battery, turn on the
ignition and wait 1 minute before starting the
engine, to enable the electronic systems to
initialise.
If minor problems nevertheless persist following
this operation, contact a CITROËN dealer.
Referring to the relevant section, initialise or
reset certain equipment:
–

Date and time.
–


Preset radio stations.
Towing the vehicle
General recommendations
Observe the legislation in force in the
country where you are driving.
Ensure that the weight of the towing vehicle is
higher than that of the towed vehicle.
The driver must remain at the wheel of the
towed vehicle and must have a valid driving
licence.

62
10" Touch Screen
10" Touch Screen
Multimedia audio system
The functions and settings described may vary according to the vehicle version
and configuration.
Driving while distracted can result in loss
of vehicle control, crash and injury. We
strongly recommend that you use extreme
caution when using any device that may take
your focus off the road.
Your primary responsibility is the safe
operation of your vehicle.
We recommend against the use of any hand-
held device while driving and encourage
the use of voice-operated systems when
possible.
Make sure you are aware of all applicable
local laws that may affect the use of electronic
devices while driving.
For safety reasons and because they
require sustained attention by the driver,
the following operations must be carried out
with the vehicle stationary and the ignition on:
–

Pairing the smartphone with the system in
Bluetooth® mode.
–
Connection to the Apple CarPlay® or
Android Auto applications.
–

Using the smartphone.
– Changing the system settings and
configuration.
Some functions are not accessible when
driving.
Overheating
In very hot conditions, operation may be
limited to protect the system (e.g. volume may
be reduced). A warning message is displayed
on the screen.
The system will resume normal operation
when the temperature in the passenger
compartment has dropped.
The system is protected in such a way that it will only operate in the vehicle.
For more information about smartphones
and OS compatibility, refer to the
following website:
https://citroen.in/citroen-connectivity
General information
Getting to know your
system
The system allows you to interact with a variety
of features using the touch screen and voice
commands. By integrating with your Bluetooth
®-enabled
phone, the touch screen provides easy
interaction with audio, multimedia, navigation,
and your phone's compatible applications.
Your system is equipped with a feature that
allows you to access and control audio features
for 60 minutes after you switch the ignition off
(until the doors are locked using the remote
control).
Layout of the touch screen
To operate the touch screen, simply touch the
item or option that you want to choose. The
button changes colour when you select it.


1. Display off (short press)
Power off (long press)
2. Connected device status with battery and
signal strength (when mobile phone is
connected)
3. Status bar
This bar displays icons and messages
pertaining to current system activities.
4. Date and time
5. Global volume control
6. Menus

66
10" Touch Screen
recommend keeping the smartphone's
operating system up-to-date, together with the
date and time on the smartphone and the
system.
Refer to your smartphone for Android Auto or
Apple CarPlay
® settings.
For the list of suitable smartphones, visit
the Android Auto and Apple CarPlay®
websites:
https://www.android.com/auto/
https://www.apple.com/in/ios/carplay/
Stop the car before connecting Android
Auto or Apple CarPlay® and follow the
instructions on your phone.
On connecting the USB cable, the
Android Auto or Apple CarPlay® function
deactivates the system's Bluetooth® mode.
Android Auto
Ensure the latest Android Auto
application is available on your
smartphone. If not, install it via "Play Store".
The Android Auto function requires the use
of a compatible smartphone and compatible
applications.


Connecting Android Auto smartphone can be
carried out either by USB cable or using a
wireless connection.
USB connection
Connect the USB cable.
Android Auto is automatically launched a few
seconds after the USB connection has been
established. A validation procedure on the
smartphone has to be followed for the first
connection, with the vehicle stationary.
The smartphone charges when connected by the
USB cable.
Wireless connection
The wireless connection of an Android Auto
device can be initiated from the Device List
menu or home screen Android Auto icon.
First activate the smartphone’s Bluetooth
®
function.
Select Device List menu to display the device to
be connected to Android Auto.
If the device has already been connected to the
system via Bluetooth
®, select the Android Auto
of the desired device from the list of connected
Android phones.
For wireless Android Auto, subsequent automatic
connection of the smartphone requires activation
of Bluetooth
® and Wi-Fi on your device.As soon as the connection is established, select this menu to display the Android
Auto interface.
There may be a pause before applications become available,
depending on the quality of the network and
performances of the phone.
Apple CarPlay®
The Apple CarPlay® function requires the
use of a compatible smartphone and
compatible applications.
Connecting Apple CarPlay
® smartphone can
be carried out either by USB cable or using a
wireless connection.
USB connection
Connect the USB cable.
The smartphone charges when connected by the
USB cable.
From the system, press Apple CarPlay®
menu to display the Apple CarPlay®
interface or press Device List menu to display
the list of connected devices and then select
Apple CarPlay
®.
When the USB cable is disconnected
and the ignition is switched off then back

67
10" Touch Screen
10on, the system will not automatically switch to
other mode; the source must be changed
manually.
Wireless connection
The wireless connection of an Apple CarPlay®
device can only be initiated from the Device List
menu.
First activate the smartphone’s Bluetooth
®
function.
Select Device List menu to display the devices
to be connected to Apple CarPlay
®.
If the device has already been connected to the
system via Bluetooth
®, select Apple CarPlay on
the desired device from the list of connected
Apple phones.
For wireless Apple CarPlay
®, subsequent
automatic connection of the smartphone requires
activation of Bluetooth
® and Wi-Fi on your
device.
Visit the Apple CarPlay
® website at:
https://www.apple.com/ios/carplay/
Media

Insert the USB memory stick into the USB port
or connect the USB device/iPod to the USB port
using a suitable cable (not supplied).
USB device format supported: FAT16 or FAT32.
To protect the system, do not use a USB hub.
Music
The system supports MP3 and WAV audio file
types.
The system builds music playlists (in temporary
memory); this operation can take from a
few seconds to several minutes at the first
connection.
Reduce the number of non-music files and the
number of folders to reduce the waiting time.
Playlists are updated whenever the ignition
is switched off or a USB memory stick is
connected. The audio system memorises these
lists, which will subsequently load faster if they
have not been changed.
Videos
The system can play video files in the AVI, WMV,
MP4, MOV, M4V, DAT and VOB formats.
Video control commands are accessible only
through the touch screen.
When the vehicle is in motion, video playback
will cut off and only audio playback will be
available.
USB video is not available if Android Auto or
Apple CarPlay
® is active/connected.
For safety reasons, park the vehicle
before playing a video.
BT Audio

When a smartphone is paired to the system,
streaming allows you to listen to the audio feed
from your smartphone.
The Bluetooth
® profile must be activated.
First adjust the volume on the portable device
(to a high level). Then adjust the volume of the
audio system.
If play does not start automatically, it may be
necessary to start the audio playback from the
smartphone.
Browse button is available if supported by the
smartphone application.
Control is from the portable device or by using
the system's touch buttons.
Once connected in streaming mode, the
smartphone is considered to be a media
source.

72
Alphabetical index
P
Pads, brake 40
Paint
41
Parking sensors, audible and visual

33
Parking sensors, rear

33
Plates, identification

60
Port, USB

18
Pressures, tyres

40, 61
Pre-tensioning (seat belts)

25
Protecting children

26–28
Puncture

42
R
Recirculation, air 18
Reminder, lighting on
20
Remote control

9–10
Removing a wheel

43–44
Replacing bulbs

45–47
Replacing fuses

48
Replacing the air filter

40
Replacing the oil filter

40
Replacing the passenger compartment
filter

40
Reservoir, screenwash

38
Reversing lamps

47
Roof rack

41
S
Safety, children 26–28
Screenwash
21
Screenwash, front

21
Seat belts

24–25
Seats, front

14
Seats, rear

15–16
Serial number, vehicle

60
Servicing

7, 39, 40–41
Sidelamps

47
Starting the engine

31
Starting the vehicle

31–32
Starting using another battery

56
Stay, engine bonnet

36
Steering wheel (adjustment)

15
Stopping the vehicle

31–32
Storage

18
Suspension

40
Switch, ignition

31
Switching off the engine

31
T
Tables of engines 60
Tables of fuses
48, 51
Tank, fuel

35
Technical data

60
Temperature, coolant

7
Tools

42
Towing

58–59
Trip computer 7–8
Tyres
40, 61
U
Unlocking 9
Unlocking from the inside
10
Unlocking the doors

10
V
Ventilation 16
W
Warning and indicator lamps 5
Warning lamp, driver's seat belt not
fastened

25
Warning lamps

5
Warning lamp, seat belts

25
Warnings and indicators

5
Washing (advice)

41
Wheel, spare

40, 42–44
Wipers

21
Wipers, windscreen

21