boot Citroen C3 PICASSO 2012 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2012, Model line: C3 PICASSO, Model: Citroen C3 PICASSO 2012 1.GPages: 244, PDF Size: 8.21 MB
Page 83 of 244
5
81
VISIBILITY
The lighting time varies accord-
ing to the circumstances:
- when the ignition is off, ap-
proximately ten minutes,
- in energy economy mode, ap-
proximately thirty seconds,
- when the engine is running,
no limit. This comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed.
Torch
This is a removable lamp, fi tted in the
side of the boot, which can be used to
illuminate the boot or as a torch.
BOOT LAMP
Use
)
Extract the torch from its location by
pulling it from the front.
)
Press the switch, located on the
back, to switch the torch on or off.
)
Unfold the support, located on the
back, to set down and raise the
torch; for example, when changing
a wheel.
Storing
)
Put the torch back in place in its lo-
cation starting with the rear.
If you have forgotten to switch off
the torch, this switches it off auto-
matically.
It the torch is not engaged correctly, it
may not charge and may not come on
when the boot is opened.
Operation
This torch operates with NiMH type re-
chargeable batteries.
It has a battery life of approximately
45 minutes and charges while you are
driving.
Observe the polarities when fi t-
ting the batteries.
Never replace the rechargeable
batteries with single-use batteries.
Page 90 of 244
6
88
FITTINGS
Opening
)
Lower the storage shelf.
)
Press the fl ap opening control.
)
Lower the fl ap.
)
Check that the adjustable boot fl oor
is in the high position.
)
Load the objects from inside the
boot.
Device for storing and transporting long
objects.
When unfolded, this provides a storage
area split into 2 sections, completing
the storage spaces available at the rear
of the vehicle.
Storage tray
Page 91 of 244
6
FITTINGS
Boot fittings
1.
Storage net on right-hand boot trim.
2.
Open storage compartments.
3.
Torch.
4.
Adjustable boot fl oor.
5.
Carrier bag hook.
6.
Securing rings.
7.
Storage area under boot carpet
8.
Rear parcel shelf.
Page 92 of 244
6
90
FITTINGS
2-position adjustable boot
The two-position adjustable boot fl oor
allows you to:
- maximise the volume of the boot,
- partition the boot (stowing the rear
shelf...),
- obtain a fl at fl oor from the boot open-
ing to the front seats, when the rear
bench seat is in the folded and fully
back position.
Placing the adjustable boot fl oor in
the low position
)
Lift the adjustable boot fl oor by pull-
ing on the strap.
)
Move the adjustable boot fl oor rear-
wards and then down, following the
guides on the sides.
Placing the adjustable boot fl oor in
the high position
)
Lift the adjustable boot fl oor by pull-
ing the strap.
)
Move the adjustable boot fl oor rear-
wards then up to its high position.
In the high position, the adjustable boot
fl oor allows stowing of the rear parcel
shelf and fragile objects.
The adjustable boot fl oor is fi tted with
four stowing rings to secure your loads
using the net available as an acces-
sory.
Ensure that your boot is empty
before handling the adjustable
boot fl oor.
Page 93 of 244
6
91
FITTINGS
Hooks Rear parcel shelf
This consists of three sections.
The front section is fl exible, and the
central and rear sections are rigid.
The rear section is secured to the tail-
gate by two cords.
To remove it from the boot:
)
unhook the two cords,
)
gently lift up the cover to remove it
from its fi xings,
)
remove the cover.
It can be stored under the adjustable
boot fl oor, if this is in its high position. The hooks can be used to hold shop-
ping bags.
Page 137 of 244
11
135
PRACTICAL INFORMATION
TEMPORARY PUNCTURE REPAIR KIT
Complete system consisting of a com-
pressor and a sealant cartridge which
permits temporary repair
of a tyre so
that you can drive to the nearest garage.
It is designed to repair most punctures
which could affect the tyre, located on
the tyre tread or shoulder.
Description of the kit
The speed limit sticker I
must
be affi xed to the vehicle's steer-
ing wheel to remind you that a
wheel is in temporary use.
Do not exceed a speed of
50 mph (80 km/h) when driving
with a tyre repaired using this
type of kit.
A.
"Sealant" or "Air" position selector.
B.
On "I"
/off "O"
switch.
C.
Defl ation button.
D.
Pressure gauge (in bar or p.s.i.).
E.
Compartment housing:
- a cable with adaptor for 12 V socket,
- various infl ation adaptors for ac-
cessories, such as balls, bicycle
tyres...
F.
Sealant cartridge.
G.
White pipe with cap for repair.
H.
Black pipe for infl ation.
I.
Speed limit sticker.
Access to the kit
This kit is installed in the storage box,
under the boot fl oor.
Page 142 of 244
11
140
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed under the boot
fl oor.
For access to them:
)
open the boot,
)
remove the boot fl oor,
)
lift up the boot carpet,
)
remove the box containing the tools,
)
remove the polystyrene storage box. All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
List of tools
Other accessories
5.
Removable towing eye.
Refer to the paragraph "Towing the
vehicle".
Access to the tools
Wheel with trim
When removing the wheel
, fi rst
detach the trim using the wheel-
brace 1
pulling at the valve pas-
sage hole.
When refi tting the wheel
, refi t
the trim starting by placing its
notch facing the valve and press
around its edge with the palm of
your hand.
1.
Wheelbrace.
For removing the wheel trim and
removing the wheel fi xing bolts.
2.
Jack with integral handle.
For raising the vehicle.
3.
"Bolt cover" tool.
For removing the bolt protectors
(covers) on alloy wheels. Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
4.
Socket for the security bolts (located
in the glove box).
For adapting the wheelbrace
to the special "security" bolts (if
your vehicle has them).
Page 143 of 244
11
PRACTICAL INFORMATION
Fitting the steel or "space-saver"
type spare wheel
If your vehicle is fi tted with alloy
wheels, it is normal to notice,
when tightening the bolts on fi t-
ting, that the washers do not
come into contact with the steel
or "space-saver" type spare
wheel. The wheel is secured by
the conical contact of each bolt.
Access to the spare wheel
The spare wheel is installed in the boot
under the fl oor.
According to country, the spare wheel may be steel or of the "space-saver" type.
For access to it, refer to the paragraph
"Access to tools" on the previous page.
Taking out the wheel
)
Unscrew the yellow central bolt, and
remove it.
)
Raise the spare wheel towards you
from the rear.
)
Take the wheel out of the boot.
Putting the wheel back in place
)
Put the wheel back in its housing.
)
Refi t the yellow central bolt in the
centre of the wheel.
)
Tighten fully until the central bolt
clicks to retain the wheel correctly.
)
Put the polystyrene storage box
back in place.
)
Put the box back in place and clip it.
Page 145 of 244
11
PRACTICAL INFORMATION
List of operations
)
Put the wheel in place on the hub.
)
Screw in the bolts by hand as far as
possible.
)
Pre-tighten the security bolt (if your ve-
hicle has them) using the wheelbrace 1
fi tted with the security socket 4
.
)
Pre-tighten the other bolts using the
wheelbrace 1
only.
)
Lower the vehicle fully.
)
Fold the jack 2
and detach it.
After changing a wheel
To store the punctured wheel in
the boot correctly, fi rst remove
the central cover.
When using the "space-saver"
type spare wheel, do not ex-
ceed 50 mph (80 km/h).
Have the tightening of the bolts
and the pressure of the spare
wheel checked by a CITROËN
dealer or a qualifi ed workshop
without delay.
Have the punctured wheel re-
paired and replace it on the vehicle
as soon as possible.
Refitting a wheel
)
Tighten the security bolt (if your vehi-
cle has them) using the wheelbrace 1
fi tted with the security socket 4
.
)
Tighten the other bolts using the
wheelbrace 1
only.
)
Refi t the bolt covers on each of the
bolts (with alloy wheels only).
)
Store the tools in the box.
Page 150 of 244
11
148
PRACTICAL INFORMATION
Changing foglamp/reversing lamp
bulbs
)
open the boot,
)
press on the tabs using 2 screwdrivers,
)
disconnect the lamp unit connector,
)
turn the bulb holder by a quarter turn,
)
remove the bulb and replace it.
To r efi t, carry out these operations in
reverse order.
Changing the third brake lamp bulbs
(4 x W 5 W bulbs)
)
open the boot,
)
remove the two plugs located on the
boot inner panel,
)
press on the body of the lamp with
2 screwdrivers to remove it from its
housing,
)
turn the corresponding bulb-holder
a quarter turn,
)
pull the bulb and replace it.
To r efi t, carry out these operations in
reverse order.
Changing the number plate lamp
bulbs (W5W)
)
insert a thin screwdriver into one of
the lens' exterior holes,
)
push it outwards to unclip.
)
remove the lens.
)
pull the bulb and replace it.
To r efi t, carry out these operations in
reverse order.