ESP Citroen C3 PICASSO 2012 1.G Owner's Manual

Guide-me-home lighting
After the ignition has been switched off, the headlamps
remain on briefl y to make your exit from the vehicle
easier when the light is poor.



75, 76



ASR and ESP systems
These systems are linked to assure the
directional stability of the vehicle, within
the limits of the laws of physics.



103


Glass panoramic sunroof
This roof provides incomparable visibility
and light in the passenger compartment.



69


Rear parking sensors
This system warns you if an obstacle is
detected behind the vehicle when re-
versing.



125


EXTERIOR


Stop & Start
This system puts the
engine temporarily into
standby during stops
in the traffi c (red lights,
traffi c jams, etc...). The
engine restarts auto-
matically as soon as you
want to move off. The
Stop & Start system re-
duces fuel consumption,
exhaust emissions and
the noise level when sta-
tionary.



11 8

9
FAMILIARI
S
AT I
ON


1.
Steering lock and ignition.

2.
Audio equipment steering mounted
control stalk.

3.
Wiper/screenwash/trip computer
control stalk.

4.
Central adjustable air vents.

5.
Storage tray.
Scented air freshener.

6.
Sunshine sensor.

7.
Passenger's air bag.

8.
Side adjustable air vent.

9.
Passenger's airbag deactivation
switch.

10.
Glove box.

11 .
Dynamic stability control
(ESP/ASR) switch
Parking sensors switch.
Central locking switch.
Hazard warning lamps switch.
Stop & Start switch.

12.
Heating/air conditioning controls.

13.
Audio equipment.

14.
Emergency or assistance call.

15.
12 V socket (100 W max).

16.
USB port/auxiliary socket.

17.
Cup holder.

18.
Heated seat controls.

19.
Parking brake.



INSTRUMENTS AND CONTROLS

13
FAMILIARI
S
AT I
ON

Lighting

Ring A


Ring B


Raise or lower the lighting stalk passing
the point of resistance; the corresponding
direction indicators will fl ash for as long as
the stalk remains in this position.

Direction indicators

Switching on "AUTO" mode



)
Press the stalk down and release it.

Ring B: rear wiper




73





78


Lighting off.
Automatic illumination of head-
lamps.
Sidelamps.
Dipped/main beam headlamps.
Rear foglamp.
or
Front and rear foglamps.
Park.
Intermittent wipe.
Wash-wipe.
Control stalk A: windscreen wipers




77

Wipers

Switching off "AUTO" mode



)
Push the stalk up and return it to po-
sition "0"
.



79




101


"Motorway" function

Press the lighting stalk up or down once,
without passing the point of resistance;
the corresponding direction indicators
will fl ash three times.
You can use this function at any speed,
but it is particularly useful when changing
lane on high-speed roads.

15
FAMILIARI
S
AT I
ON

Translucent digital instrument panel
Switch panels


A.
With the ignition on, the level of fuel
remaining is displayed in the digital
instrument panel

B.
With the ignition on, the oil level in-
dicator should display "OIL OK"
for
a few seconds.
If the levels are not correct, top up the
levels which are low. Lighting of the indicator lamp indicates
the status of the corresponding function.


A.
Deactivation of the ESP/ASR system.

103


B.
Deactivation of the rear parking sen-
sors.


126


C.
Central locking.


67


D.
Deactivation of Stop & Start.


11 9



With the ignition on, the orange and red
warning lamps come on.
With the engine running, these warn-
ing lamps should go off almost immedi-
ately, with the exception of the warning
lamp C
(passenger's front airbag activat-
ed) which goes off after approximately
one minute.
If warning lamps remain on, refer to the
relevant page.
Warning lamps



22




23


MONITORING

1
23
MONITORING
Certain warning lamps may
come on in two different modes.
Only by relating the type of illu-
mination to the operating status
of the vehicle can it be ascer-
tained whether the situation is
normal or whether a fault has
occurred.
Indicator and warning lamps

Visual indicators informing the driver that a system is in operation (operation or deactivation indicator lamps) or of the occur-
rence of a fault (warning lamp).

Associated warnings
The illumination of certain warning lamps may be accompanied by an audible
signal and a message in the multifunction screen.
The warning lamps may come on continuously (fi xed) or fl ash.

Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding
system has come into operation.

When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignition is switched on.
When the engine is started, these same warning lamps should go off.

If they remain on, before moving off, refer to the information on the warning lamp concerned.



Warning lamp



is on



Cause



Action/Observations






Left-hand
direction
indicato

r


fl ashing with
buzzer. The lighting stalk is pushed
down.




Right-hand
direction
indicator


fl ashing with
buzzer. The lighting stalk is pushed
up.





Sidelamps


fi xed. The lighting stalk is in the
"Sidelamps" position.




Dipped beam
headlamps


fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position.




Main beam
headlamps


fi xed. The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam headlamps.

1
26
MONITORING










Deactivation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding system has been switched off intentionally.
This is may be accompanied by an audible signal and a message on the multifunction screen.



Warning lamp



is on



Cause



Action/Observations






Passenger's
airbag
system


fi xed. The control switch, located
at the passenger's end of
the dashboard, is set to the
"OFF

"
position.
The passenger's front
airbag is deactivated.
In this case you can install
a "rear facing" child seat. Set the control switch to the "ON"
position to
activate the passenger's front airbag. In this
case, do not fi t a child seat in the rear-facing
position.





ESP/ASR


fi xed. The button, located in the
middle of the dashboard, is
pressed. Its indicator lamp
is on.
The ESP/ASR is deactivated.
ESP: electronic stability
programme.
ASR: anti-skid regulation. Press the button to activate the ESP/ASR. Its
indicator lamp switches off.
The ESP/ASR system is activated automatically
when the vehicle is started.
If deactivated, the system is reactivated
automatically from approximately 30 mph
(50 km/h).

1
28
MONITORING


Warning lamp



is on



Cause



Action/Observations






Anti-lock
Braking
System
(ABS)


fi xed. The anti-lock braking
system has a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a
CITROËN dealer or a qualifi ed workshop without
delay.




Dynamic
stability
control
(ESP/ASR)


fl ashing. The ESP/ASR regulation is
active. The system optimises traction and improves the
directional stability of the vehicle.

fi xed. Unless it has been
deactivated (button pressed
and its indicator lamp on) the
ESP/ASR system has a fault. Have it checked by a CITROËN or a qualifi ed
workshop.


Engine
autodiagnosis
system


fl ashing. The engine management
system has a fault. Risk of destruction of the catalytic converter.
Have it checked by a CITROËN dealer or a
qualifi ed workshop.

fi xed. The emission control
system has a fault. The warning lamp should go off when the engine
is started.
If it does not go off, contact a CITROËN dealer or
qualifi ed workshop without delay.





Low fuel level


fi xed. When it fi rst comes on there
remains approximately
5 litres of
fuel
in the tank. You must refuel as soon as possible to avoid
running out of fuel.
This warning lamp will come on every time the
ignition is switched on, until a suffi cient addition
of fuel is made.
Fuel tank capacity: approximately 50 litres
(petrol) or 48 litres (Diesel); depending on
version: approximately 30 litres (petrol or Diesel).
Never continue to drive until you run out of fuel
as this could damage the emission control and
injection systems.

2
36
MULTIFUNCTION SCREENS

Vehicle confi guration

Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not ac-
tive, faulty).
Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-Brasil,
Türkçe, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km,
mpg or km/l).



)
Once you have selected a setting,
press the "OK"
button to change its
value.

)
Wait for approximately ten seconds
without any action to allow the changed
data to be recorded or press the "ESC"

button to cancel.
The screen then returns to the normal
display.

Once the "Vehicle confi guration" menu
has been selected, you can activate or
deactivate the following equipment:


- wiper linked with reverse gear (refer
to the "Visibility" section),

- "guide-me-home" lighting (refer to
the "Visibility" section).
Once the fuel consumption unit
has been changed to mpg, the
information relating to speed and
distance also changes to miles.
For safety reasons, confi gura-
tion of the multifunction screen
by the driver must only be done
when stationary.

2
38
MULTIFUNCTION SCREENS
Once the fuel consumption unit
has been changed to mpg, the
information relating to speed
and distance also changes to
miles.
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.
Language
Once the "Language" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).

Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100km, mpg or
km/l).


)
Once you have selected a setting,
press the " 
" or " 
" buttons to
change its value.

)
Press the " 
" or " 
" buttons to
switch respectively to the previous
or next setting.

)
Press the "OK"
button to record the
change and return to the normal dis-
play or press the "ESC"
button to
cancel.



Vehicle confi guration


Options
Once the "Options" menu has been se-
lected, you can start diagnostics of the
status of the equipment (active, not active,
faulty). Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:


- wiper linked with reverse gear (refer
to the "Visibility" section),

- "guide-me-home" lighting (refer to
the "Visibility" section).

For safety reasons, confi gura-
tion of the multifunction screen
by the driver must only be done
when stationary.

2
40
MULTIFUNCTION SCREENS

Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active, not
active, faulty).

Language
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-Brasil,
Deutsch, English, Espanol).

Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or
km/l). colour screen


"SETUP" menu
Date and time
This menu allows you to adjust the date
and time, and their format (refer to the
"Audio and telematics section").

Display
This menu allows you to adjust the
brightness of the display, the display
contrast and the colour of the map (day/
night and auto mode).

System parameters
This menu allows you to restore the
factory settings, to display the software
version and to activate scrolling text. This displays the following information:


- time,

- date,

- audio functions,

- navigation system information. The chosen language will also
be used by the MyWay system
colour screen.
Once the fuel consumption unit
has been changed to mpg, the
information relating to speed
and distance also changes to
miles.
For safety reasons, confi gura-
tion of the multifunction screen
by the driver must only be done
when stationary.
For safety reasons, confi gura-
tion of the multifunction screen
by the driver must only be done
when stationary.

Press the SETUP button to access the
"SETUP"
menu. It gives you access to
the following functions:


- Date and time,

- Display,

- System parameters.