Top Citroen C3 PLURIEL 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 243
INJECTION
SAFETY REQUIREMENTS: HDi DIRECT INJECTION SYSTEM
Engines: HDi ALL TYPES
SAFETY REQUIREMENTS.
Preamble.
All interventions on the injection system must be carried out to conform with the following requirements and regulations:
Competent health authorities.
Accident prevention.
Environmental protection.
WARNING:Repairs must be carried out by specialised personnel informed of the safety requirements and of the precautions to be taken.
Safety requirements.
IMPERATIVE: Take into account the very high pressures in the high pressure fuel circuit (1350 bars), and respect the requirements below: No smoking in proximity to the high pressure circuit when work is being carried out.
Avoid working close to flame or sparks.
Engine running: Do not work on the high pressure fuel circuit.
Always stay clear of the trajectory of any possible jet of fuel, which could cause serious injuries.
Do not place your hand close to any leak in the high pressure fuel circuit.
After the engine has stopped, wait
30 secondsbefore any intervention.
NOTE:This waiting time is necessary in order to allow the high pressure fuel circuit to return to atmospheric pressure.

Downloaded from www.Manualslib.com manuals search engine 255
INJECTION
ADJUSTING THE MECHANICAL CONTROLS OF THE DELPHI INJECTION PUMP
Engine: WJY
Adjusting the fast idle.
Engine cold.
Ensure that the lever (2)is up against its stop to the right.
If not, adjust the tension of the cable (3)using the cable clamp (1).
Finish tensioning using the sleeve tensioner (4).
Engine hot. Check that the cable (3)is in tension.
Checking the thermostatic sensor. There should be a minimum 6 mmcable travel between a cold and a hot engine.
Adjusting the accelerator control.
Prior conditions.
Engine hot (cooling fan is engaged twice).
Checking the accelerator cable tension. Fully depress the accelerator pedal.
Check that the lever (6)is against its stop (5)otherwise, alter the position of the pin.
If not, adjust the position of the accelerator cable tensioning retaining pin.
Ensure that in the idle position the lever
(6)is against the stop (7).
B1HP0K9C
XSARA

Downloaded from www.Manualslib.com manuals search engine 256
INJECTION
ADJUSTING THE MECHANICAL CONTROLS OF THE DELPHI INJECTION PUMP
Engine: WJY (continued)
Adjusting the antistall (residual output).
Insert a 3 mmthick shim (10)between the throttle lever (6)and the antistall screw (7).
Push the stop lever (8).
Insert a 3 mmdiameter peg (9)in the lever (2).
Adjust the engine speed to 1500 rpm ± 100using the stop screw (7).
Remove the shim (10)and the peg (9).
Adjusting the idle speed.
Adjust the speed using the idle adjustment screw (11).
Idling speed:825 ± 25 rpm.
Checking the engine deceleration.
Move the throttle lever (6)to obtain an engine speed of 3000 rpm.
Release the throttle lever (6).
The deceleration should be between 2.5and 3.5seconds.
The drop should be approximately 50 rpmin relation to the idle speed.
Deceleration too fast, (the engine has a tendency to stall)slacken the screw (7)by a quarter turn.
Deceleration too slow, (engine speed is greater than the idle speed)tighten screw (7)by a quarter turn.
NOTE:In each case, check the idle speed for any necessary adjustments.
B1HP0K9CB1HP0KAC
XSARA

Downloaded from www.Manualslib.com manuals search engine 273
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
General.
ESSENTIAL: Given the very high pressures prevailing in the fuel high pressure circuit (1600 Bars), respect the following regulations.
It is forbidden to smoke in the immediate proximity of the high pressure circuit during a repair.
Avoid working close to flames or sparks.When the engine is running:
Do touch the fuel high pressure circuit.
Always keep out of range of possible projections of fuel, which could cause serious injuries.
Do not place your hand near to any leak on the fuel high pressure circuit. After the engine has stopped, wait 30 seconds before starting any operation.
NOTE:The waiting time is necessary to allow the fuel high pressure circuit to return to atmospheric pressure.
Safety rules.
IMPERATIVE:Wait at least an hour before starting any repair on the exhaust line.
Forced regeneration of the particle filter:
Check that there are no aerosols or inflammable products inside the vehicle’s boot.
Wear high temperature gloves.
Connect the vehicle to a gas extractor approved for this type of operation.
IMPERATIVE: In the absence of the required installations, carry out the forced regeneration of the particle filter outside the workshop,
in a concreted area well away from any inflammable materials. Place the vehicle in the high position.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 275
INJECTION
SPECIAL FEATURES: FORCED REGENERATION OF THE PARTICLE FILTER
Tools.
Diagnostic stations: LEXIA or PROXIA
Imperative: Respect the safety and cleanliness requirements.
Forced regeneration of the particle filter.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
ESSENTIAL: Connect the vehicle to a gas extractor approved for this type of operation.In the absence of the required installations,carry out the forced regeneration of the particle filter outside the workshop, in a concreted
area well away from any inflammable materials. Place the vehicle in the high position.
WARNING:
Check that the fuel level is sufficient (at least 20 litres).
Start the engine and allow it to warm up (60°C minimum).
Connect the diagnostic tool to the vehicle’s central socket.
Trigger the regeneration cycle, with the diagnostic tool.
Automatic running of the regeneration cycle of the particle filter:
Autocheck by the engine ECU. Stabilisation of engine speed at
4000 rpm, operating with post injection.
Change to idling speed (for 30 seconds).
Stabilisation of engine speed at 3000 rpm, checking of the efficiency of the regeneration of the particle filter.
Change to idling speed.
NOTE:Let the engine run at idling speed for the benefit of cooling.
Stop the engine.
IMPERATIVE: Wait for at least an hour before any operation on the exhaust line.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 278
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Sealing of the additive injector.
Couple tool [1] to the tube (1).
Action the manual pump [1].
WARNING:The additive injector should open at a pressure of 100 ± 20 Bars.
Action the manual pump in vacuum
[1]at 800 m.bars.
WARNING:The downstream pressure should not fall rapidly.
NOTE:Replace the fuel tank if the injector is defective.
Couple the tube
(1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid ofLEXIAor PROXIA.
Check the additive level.
The checking of the additive level is done with reference to the gradations «a»marked on the additive
reservoir.
The top graduation indicates maximum filling
(3 Litres).
The difference between the two gradations equates to 0,25 Litres.
XSARA PICASSO
B1HP1UUC
B1KP019C

Downloaded from www.Manualslib.com manuals search engine 289
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Refitting.
Place the pedal in the high position (contact at “a”).
Attach the cable yoke on the hook of the clutch pedal.
Fit a new clip
(3).
Fit the endpiece (4)to the bulkhead (fit with G6grease).
Clip the endpiece (5)on the gearbox.
Couple the cable to the lever (1).
Depress the clutch cable several times to lodge the cable in place.
Check that the endpiece (4) is correctly lodged on the bulkhead.
Check the operation of the automatic adjusting system.
After fitting the cable, pull the clutch lever in the inverse direction
(direction F), the lever should
move back when pulled by hand.
Press the clutch pedal very lightly and repeat the same operation. The lever should not move
back.
WARNING:If a system blockage is detected when checking, or if the pedal has been removed,
the pedal position must be adjusted. The correct positioning of the pedal is obtained by the
angular displacement of the stop supports
"a"and "b".
B2BP03CD
XSARA XSARA PICASSO
«PUSH» clutch
«PULL» clutch
B2BP03DD

Downloaded from www.Manualslib.com manuals search engine 290
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Adjusting the pedal height.
Loosen the nut (6)and the screw (7).
Using a lever, raise the stop support (8)to its highest position. In this position, there should be a substantial free
play in the pedal.
Lower the support until there is a free play of
2 ± 1 mm.
Tighten the nut (6) and the screw (7).
Check that the clutch cable sleeve can move freely.
At rest, the clutch cable sleeve should be free and able to lengthen and shorten.
Clutch pedal travel.
The automatic clutch wear adjustment system has no manual adjustment.
Pedal travel is identical on all models:154 ± 5 mm.
The adjustment is achieved by reducing the length of the cable sleeve.
WARNING:Automatic adjustment of the pedal travel is accompanied by a modification of the curvature of the
cable sleeve. Do not add any supplementary fixing points or alter the routing in any way.
«c»Routing of new cable.«b»Routing after adjustment of play.«x» Clutch wear.
B2BP03ECB2BP03FD
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 292
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS HYDRAULIQUE
Bleeding the hydraulic clutch control
Action the clutch pedal manually through its full travel:7 times rapidlydown and up.
Allow the clutch pedal to come back up to its high position.
Fill the brake fluid reservoir to the maximum of its capacity.
Open the bleed screw, at
«c».
Action the clutch pedal manually through its entire travel:7 timesrapidly down and up.
The last time, keep the clutch pedal fully down.
Reclose the bleed screw, at
«c».
If necessary, repeat the operation.
Top up the brake fluid to the MAX. level of the brake fluid reservoir.
Work the clutch vigorously
40 times.
Start the engine.
Apply the handbrake.
Engage a gear.
Check that the clutch starts to engage at a dimension
(X)greater than or equal to 45 mm(the dimension (X)is
given as a guide).
Repeat the bleed operations if necessary.
C5FP0FQCB2BP04YC
C2 C3 C3 PLURIEL
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 303
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: HFX KFV NFU 8HX 8HW
Tightening torques (m.daN).
(26)
5th gear cover fixing screw(3 screws): 2,2 ± 0,2
(27) Reverse gear switch (1 screw): 2,5 ± 0,5
(28)Drain plug (1 screw):3,3 ± 0,3
(29) Topup plug (1 screw): 3,3 ± 0,3 (*)
(*) =
The oil topup plug is discontinued from RPO 9919
Features.This gearbox:
has no adjustment. has a reverse gear braking device
(5th gear synchroniser).
has a device for prohibiting a change from 5th gear into reverse gear.
The clutch control has a balljoint mounted declutch fork.
Lubrication.Oil capacity :2 ±0,15 Litres.Checking the oil level: No oil level check (*)Lubrication interval:Lubricated «for life».
NOTE:There should be a visual check on the sealing at each engine oil
change.
B2CP3SSD
C2 C3 C3 PLURIEL