warning Citroen C3 RHD 2013 2.G Owner's Guide

5
Visibility
85
Association with the automatic"Guide-me-home" lighting
Association with the automatic illumination of headlamps provides "guide-me-home" lighting with the following additional options:
- selection of the lighting duration to 15, 30 or 60 seconds in the functions that can be set
in the vehicle configuration menu (except in
the case of the monochrome screen A, for
which the duration is set: 60 seconds),
- automatic activation of "guide-me-home"lighting when automatic illumination of headlamps is in operation.
Operating fault
In the event of a fault with the sunshine sensor, the lighting come on, this warning lamp is displayed in theinstrument panel and/or a message appears in
the screen, accompanied by an audible signal.
Contact a CITROËN dealer or a qualifiedworkshop.
In fog or snow, the sunshine sensor may detect sufficient light. Therefore, thelighting will not come on automatically. Do not cover the sunshine sensor, coupled with the rain sensor andlocated in the centre of the windscreen behind the rear view mirror; the associated functions would no longer be controlled.

Automatic illumination of headlamps


Activation
)Turn ring to the "AUTO"
position. Theautomatic illumination of headlamps is accompanied by a message in the screen.


Deactivation
)Turn ring to a position other than "AUTO" .
Deactivation is accompanied by a message
in the screen. The sidelamps and dipped beam headlamps
are switched on automaticall
y, without any
action on the par t of the driver, when a low level
o
f external light is detected or in certain cases
of activation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.

Safety
108











Direction indicators Selection of the left or right direction indicators
to signal a change of direction of the vehicle.
)Left: lower the lighting stalk beyond thepoint of resistance.)Right: raise the lighting stalk beyond thepoint of resistance.
"Motorway" function
)Press briefly upwards or downwards,
without going beyond the point of resistance; the direction indicators will flash 3 times.







Hazard warning lamps
)
Press this button, the direction indicatorsflash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps come on automatically.
They switch off automatically the first time you accelerate.)You can also switch them off by pressingthe button.
A visual warnin
g by means of the direction
indicators to alert other road users to a vehiclebreakdown, towing or accident.

Safety
110

Operating fault
You must stop as soon as it is safe to do so.

In either case, contact a CITROËN dealer or aqualified workshop. If this warnin
g lamp comes on,
accompanied by an audible signaland a message in the screen, it
indicates a malfunction of the anti-lock braking system which could
result in loss of control of the vehicle
when braking.
If this warnin
g lamp comes on,
together with the STOPand ABSwarning lamps, accompanied by an
audible signal and a message in the screen, it indicates a malfunction of
the electronic brake force distribution
which could result in loss of control of
the vehicle when braking.
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure morequickly, thus reducing the stopping distance.

Activation

It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
When replacing wheels (tyres and rims), ensure that they conform to the manufacturer's recommendations.

When braking in an emergency, press firmly without releasing the pressure.

















Braking assistance systems
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and manoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.
When braking in an emergency, press very firmly without releasing the pressure. Group of supplementar
y systems which helpyou to obtain optimum braking in complete safety in emergency situations:
- anti-lock braking system (ABS),
- electronic brake force distribution (EBFD),
- emergency braking assistance (EBA).

8
Safety
111














Trajectory control systems


Anti-slip regulation (ASR)
and electronic stability
programme (ESP)


The anti-slip regulation (also known as Traction Control) optimises traction to prevent skidding
of the wheels, by acting on the brakes of the
driving wheels and on the engine.
The electronic stability programme acts on the
brake of one or more wheels and on the engine to
keep the vehicle on the trajectory required by the
driver, within the limits of the laws of physics.


Activation

These systems are activated automatically each time the vehicle is started.
They come into operation in the event of a grip
or trajectory problem.
This is indicated b
y flashing of this
warning lamp in the instrument panel.

Deactivation
In exceptional conditions (starting a vehicle which is bogged down, stuck in snow, on softground...), if you are unable to make progress, it may be advisable to temporarily deactivate
these systems, so that the wheels can spin freely and allow the vehicle to move. ) Press the "ESP OFF"
button, located near
the steering wheel.
If this warning lamp comes on in the instrument panel and the indicator lamp in the button comes on, this
indicates that these systems are deactivated. It is recommended that the systems be reactivated as soon as possible.
Reactivation
These systems are reactivated automaticallyeach time the ignition is switched back on or from 30 mph (50 km/h).)
Press the "ESP OFF"
button again to reactivate them manually.


Operating fault
If this warning lamp comes on,accompanied by an audible signal
and a message in the screen, this
indicates a fault with these systems.
Have it checked by a CITROËN
dealer or a qualified workshop.
The trajectory control systems offer increased safety in normal driving, butthis should not encourage the driver totake extra risks or drive at high speed.
The correct functioning of these systems is assured provided that manufacturer's recommendations are observed on:


- wheels (tyres and rims),

- braking components,

- electronic components,

- assembly and repair procedures.
After an impact, have these systems checked by a CITROËN dealer or a qualified workshop.

Safety
112
Seat belts
Front seat belts
Fastening
)
Pull the strap, then inser t the tongue in the buckle. )
Check that the seat belt is fastened correctly by pulling the strap.
Unfastening
)Press the red button on the buckle. )Guide the seat belt as it is reeled in.



Seat belt not fastened / unfastened warning lamp
When the ignition is switched on, this
warning lamp comes on in the instrument
panel, if the driver and/or the front
passen
ger has not fastened their seat belt.

Rear seat belts

The rear seats are each fitted with a three-point
inertia reel seat belt.
Fastening
)Pull the strap, then insert the tongue in thebuckle.)Check that the seat belt is fastenedcorrectly by pulling the strap.



Unfastening
)Press the red button on the buckle.)Guide the seat belt as it is reeled in.

Th
e front seat belts are fitted with a pretensioning and force limiting system.
This s
ystem improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact, thepretensioning system instantly tightens the seat
belts against the body of the occupants.The pretensioning seat belts are active when
the ignition is on.
The
force limiter reduces the pressure of the seat belt on the chest of the occupant, so
improving their protection.

From approximatel
y 12 mph (20 km/h)
this warning lamp flashes for two minutes
accompanied by an audible signal of increasing
volume. Once these two minutes have elapsed,
this warning lamp remains on until the driver and/
or the front passenger fastens their seat belt.

8
Safety
113
The driver must ensure that passengers usethe seat belts correctly and that they are allrestrained securely before setting off. Wherever you are seated in the vehicle, always fasten your seat belt, even for shor t
journeys.
Do not interchange the seat belt buckles asthey will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the lengthof the strap to your size. The seat belt isstowed automatically when not in use.
Before and after use, ensure that the seatbelt is reeled in correctly.
The lower part of the strap must bepositioned as low as possible on the pelvis.
The upper par t must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation inthe event of a collision, emergency braking or if the vehicle rolls over. You can releasethe device by pulling firmly on the strap and releasing it so that it reels in slightly.
Recommendations for children
Use a suitable child seat if the passenger isless than 12 years old or shorter than one and a half metres.Never use the same seat belt to secure morethan one person. Never allow a child to travel on your lap.
In order to be effective, a seat belt must:- be tightened as close to the body aspossible, - be pulled in front of you with a smoothmovement, checking that it does not
twist, - be used to restrain only one person,- not bear any trace of cuts or fraying,- not be converted or modified to avoid affecting its performance.
In accordance with current safety regulations, for all repairs on your vehicle,go to a qualified workshop with the skills andequipment needed, which a CITROËN dealer is able to provide.Have your seat belts checked regularly bya CITROËN dealer or a qualified workshop,particularly if the straps show signs of damage.Clean the seat belt straps with soapy water or a textile cleaning product, sold byCITROËN dealers. After folding or moving a seat or rear benchseat, ensure that the seat belt is positionedand reeled in correctly.
In the event of an impact
Depending on the nature and seriousnessof the impact
, the pretensioning device may be deployed before and independently of theairbags. Deployment of the pretensionersis accompanied by a slight discharge of harmless smoke and a noise, due to theactivation of the pyrotechnic cartridge incorporated in the system. In all cases, the airbag warning lamp comes on.Following an impact, have the seat belts system checked, and if necessary replaced,by a CITROËN dealer or a qualified workshop.

8
Safety
115
Only the passenger's front airbag can be
deactivated:)with the ignition off, inser t the key in thefpassenger airbag deactivation switch, )turn it to the "OFF"position, )then, remove the key keeping the switch in
the new position.
This warnin
g lamp comes on in theinstrument panel when the ignition is
on and until the airbag is re-activated.
Reactivation
When you remove a child seat that has been
fitted "rear wards facing", turn switch to the
"ON"
position to re-activate the airbag and soassure the safety of your front passenger in the
event of an impact.


Operating fault
If this warning lamp comes on in the
instrument panel, accompanied by
an audible warning and a message
in the multifunction screen, contact a
CITROËN dealer or qualified workshop
to have the s
ystem checked. The airbags may no longer be deployed in
the event of a serious impact.
I
f this warning lamp flashes, contacta CITROËN dealer or a qualified
workshop. The passenger's front airbag may no longer be deployed in
the event of a serious impact.
If at least one of the two airbag warning lamps come on continuously, do not install a child seat on the front
passenger seat.
Have it checked by a CITROËN dealer or a qualified workshop.

To assure the safety of your child,the passenger's front airbag must be deactivated when you install a "rear facing" child seat on the front passenger seat.Other wise, the child would risk beingseriously injured or killed if the airbag were deployed.


Deactivation

Safety
116
Lateral airbags
Deployment
The lateral airbags are deployed unilaterally in
the event of a serious side impact applied to all
or par t o
f the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The lateral airba
g inflates between the hip andshoulder of the front occupant of the vehicle and the corresponding door trim panel.

Impact detection zones
A.
Front impact zone.
B. Side impact zone.


Curtain airbags

System which protects the driver and
passengers (with the exception of the rear centre passenger) in the event of a serious side
impact in order to limit the risk of injury to the side of the head.
Each cur tain airbag is built into the pillars and
the upper passen
ger compar tment area.

Deployment

The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or par t of the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or
rear occupant of the vehicle and the windows.

Operating fault

If this warning lamp comes on in the instrument panel, accompanied by anaudible signal and a message in thescreen, contact a CITROËN dealer or a
qualified workshop to have the systemchecked. The airbags may no longer be
deployed in the event of a serious impact.
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be
deployed.
In the event of a rear or front collision, the airbag is not deployed.
System which protects the driver and frontpassenger in the event of a serious side impact
in order to limit the risk of in
jury to the chest,
between the hip and the shoulder.
Each lateral airba
g is fitted in the seat backrest frame, door side.

Driving
118





Parking brake
Applying
)Pull the parking brake lever fully up toimmobilise your vehicle.

Releasing
)Pull the parking brake lever gently, press
the release button then lower the lever fully.
When the vehicle is bein
g driven,
if this warning lamp and the STOPwarning lamp come on, accompanied by an audible signal and a message
on the multifunction screen, this indicates that the parking brake is still
on or has not been properly released.








6-speed manual
gearbox

Engaging 5th
or 6th
gear
)
Move the lever fully to the right to engage 5th or 6th gear.
)Raise the ring under the knob and move
the gear lever to the left then forwards.


Engaging reverse gear
Only engage reverse gear when the vehicle is stationary with the engine at idle.

As a safety precaution and to facilitate starting of the engine:


- always select neutral,

- press the clutch pedal.

When parking on a slope, direct your wheels against the pavement, apply the parking brake and engage a gear.

Failure to follow this advice may cause permanent damage to the gearbox (engagement of 3rdor 4thgear bymistake).

9
Driving
121

Display in the instrument panel


Gear lever positions
N
. Neutral R
. Reverse1 2 3 4 5 / 6.Gears in manual mode.
AUTO. This comes on when automated mode
is selected. It goes off when changing tomanual mode.
) Select position N . )
Press the brake pedal fully.
)
Start the engine.
Nappears in the instrument panel.
)
Select automated mode (position A
), Amanual mode (position M ) or reverse(position R)R
AUTO
and 1, 1
or Rappear in the
instrument panel.
)Place your foot on the brakewhen this warning lamp flashes (e.g.: star ting the engine).




Creep function
(6-speed electronic gearbox
system)
This function allows the vehicle to be
manoeuvred more easily at low speeds (when
parking, in traffic jams...).
With the gear lever in position A, Mor R, the vehicle moves as soon as you take your foot off the brake pedal, at low speed and
with the engine at idle.
) Release the parking brake.)
Progressively take your foot off the brake
pedal.
) Accelerate away.
Vehicles fitted with the 6 -speed
electronic gearbox system then move off on their own (refer to the paragraph"Creep function").

Do not leave children unsuper visedinside the vehicle when the engine is running.
You must keep your foot on the brake pedal while star ting the engine.
Do not press the brake and clutch
pedals simultaneously. This can cause rapid clutch wear.
Nflashes in the instrument panelscreen if the gear lever is not inposition N
when star ting.

The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.

Moving off