ignition Citroen C3 RHD 2013 2.G Service Manual

Driving
136
You can activate or deactivate the system by means of the multifunction screen configuration
menu. The system state is memorised when switching off the ignition.
For more information on access to the parkingsensors menu, refer to "Configuration / Vehicleparameters" in the "Multifunction screens"section corresponding to your screen.

Operating faults
If there is an operating fault, when
reverse gear is engaged this
warning lamp comes on in the
instrument panel, accompanied b
yan audible signal (short beep) and a
message in the multifunction screen.
Programming
The system will be deactivated automatically when towing a trailer or when a bicycle carrier is fitted (vehiclefitted with a towbar or bicycle carrier recommended by CITROËN).
In bad or wintry weather, ensure thatthe sensors are not covered with mud,frost or snow.

10
Checks
143






Checking levels
Oil level


The check is carried out either when
the ignition is switched on using theoil level indicator in the instrument
panel, or using the dipstick.
Engine oil change
Refer to the MAINTENANCE AND WARR ANT Y GUIDE for details of the inter val
for this operation.
In order to maintain the reliabilit
y of the engine and emission control system, the use of additives in the engine oil is prohibited.

It is normal to top up the oil levelbetween two ser vices (or oil changes).CITROËN recommends that you check
the level, and top up if necessary, every3 000 miles (5 000 kms). After topping up the oil, the check when switching on the ignition with the oil level indicator in the instrument panel is not valid during the 30 minutes after topping up. It will onl
y be correct if the vehicle is on level ground and the engine has been off for more
than 30 minutes.
Check all of these levels re
gularly, in line with the MAINTENANCE AND WARR ANT Y GUIDE. Top them up if necessary, unless other wise indicated.
If a level drops significantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop.


Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could star t atany time (even with the ignition off).

Oil specifi cation
The oil must be the correct grade for your
engine and conform to the manufacturer'srecommendations.
Th
e brake fluid level should be close
to the "MA X" mark. If it is not, check
the brake pad wear.
Brake fluid level

Changing the fl uid

Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of the intervalfor this operation.


Fluid specifi cation

The brake fluid must conform to themanufacturer's recommendations and meet
the DOT3 or DOT4 standard.

Practical information
148
Repair procedure
1. Sealing
) Uncoil the white pipe G
fully.)
Unscrew the cap from the white pipe.)
Connect the white pipe to the valve of the
tyre to be repaired.

)Connect the compressor's electric plug to
the vehicle's 12 V socket. )Star t the vehicle and leave the engine running.
Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if
swallowed and causes irritation to the eyes. Keep this product out of the reach of children.
Avoid removing any foreign bodieswhich have penetrated into the tyre.

Do not star t the compressor before connecting the white pipe to the tyre valve: the sealant product would be expelled through the pipe.
)Switch off the ignition.
)Turn the selector Ato the"sealant" position. )Check that the switch B
is in position "O"
.

11
Practical information
155
Removing a wheel

List of operations
)
Remove the bolt cover from each of the bolts using the tool 3(with alloy wheels
only).) Fit the security bolt socket 4
on thewheelbrace 1to slacken the security bolt(if your vehicle has them).)
Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off theignition and engage first gear *
to lock the wheels. If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. It is imperative that you ensure that the occupants get out of the vehicle andwait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.
*
position R
for an electronic gearbox; position P
for an automatic gearbox.

11
Practical information
169
Fuse N°RatingFunctions
F
820 A Multifunction screen, audio system, navigation radio, instrument
panel with clock, alarm control unit, alarm siren, audio system (after-market), por table navigation system carrier supply.
F
930 A
Multifunction screen, audio system, navigation audio unit,
instrument pnael with clock, alarm control unit, alarm siren,
audio s
ystem (after-market), 12 V socket, portable navigationsupport supply, locking.
F1
015 A Steering mounted controls.
F1
115 A
Ignition, diagnostic socket, automatic gearbox control unit.
F12 15 A
Rain
/ sunshine sensor, trailer relay unit, driving school module.
F1
35 A Main stop switch, engine relay unit, electronic gearbox gear lever.
F1415 A Parking sensors control unit, airbag control unit, instrument
panel, automatic air conditioning, USB Box, HiFi amplifier, reversing camera.
F1
530 A Locking.
F1
6- Not used.
F17
40 A Rear screen and door mirrors demisting/defrosting.
S
H- PA RC shunt.

11
Practical information
171
Fuse N°RatingFunctions
F120 AEngine control unit supply, cooling fan unit control relay,multifunction engine control main relay, injection pump (Diesel).
F
215 AHorn.
F
310 AFront / rear wash-wipe.
F420 ADaytime running lamps, LED daytime running lamps.
F
515 ADiesel heater (Diesel), par ticle filter additive pump (Diesel), air
flow sensor (Diesel), fuel pump (1.1i and 1.4i), blow-by heater
and electrovalves (VTi).
F
610 A ABS/ESP control unit, secondary stop switch.
F710 AElectric power steering, automatic gearbox.
F
825 AStarter control.
F9
10 ASwitching and protection unit (Diesel).
F10
30 AFuel heater (Diesel), blow-by heater (1.1i, 1.4i and Diesel), fuel pump (VTi), injectors and ignition coils (petrol), electronic
thermostat and canister purge electrovalve (1.1i and 1.4i).
F1
140 AHeater blower.

Fuse table

Practical information
172
Fuse N°RatingFunctions
F1230 A Windscreen wipers slow / fast speed.
F13
40 A Built-in systems inter face supply (ignition positive).
F14
30 A Valvetronic supply (VTi).
F1
510 A Right-hand main beam headlamps.
F1
610 A
Left-hand main beam headlamps.
F17 15 A
Left-hand dipped beam headlamps.
F18 15 A
Ri
ght-hand dipped beam headlamps.
F1
915 A Oxygen sensors and electrovalves (VTi), electrovalves (Diesel),
EGR electrovalve (Diesel).
F20 10 A Pumps, electronic thermostat
(VTi), water in fuel sensor (Diesel).
F2
15 A Fan assembly control supply, ABS/ESP.

11
Practical information
175

Starting using another
batter
y

Charging the battery using
a battery charger

When the battery on your vehicle is discharged,
the engine can be star ted using a slave battery (external or on another vehicle) and jump leads.
) Follow the instructions for use provided by
the manufacturer of the charger.

First check that the slave battery has a nominal
voltage of 12 V and a capacity at least equal to
that of the discharged battery.
Do not try to star t the engine by connecting a
batter
y charger.
Do not disconnect the (+) terminal when theengine is running.
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B
.)Connect one end of the green or blackcable to the negative terminal (-) of the slave battery B
(or ear th point on the other
vehicle).)Connect the other end of the green or black cable to the negative terminal C(or
the engine mounting) of the broken-down
vehicle.)Star t the engine of the other vehicle and
allow it to run for a few minutes.
Do not disconnect the battery to charge it.
)
Operate the star ter of the broken-down
vehicle and let the engine run.
If the engine does not star t immediately, switch off the ignition and wait a few
moments before trying again.) Wait until the engine returns to idle, then
disconnect the jump leads in reverse order.


Batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordance with regulationsand must not, in any circumstances, bediscarded with household waste.
Take used remote control batteries and vehicle batteries to a special collection
point.

Practical information
178








Changing a front or rear wiper blade
Removal
)Raise the corresponding wiper arm.)Unclip the wiper blade and remove it.


Fitting
)
At the front, check the size of the wiper blade as the shorter blade is fitted to the
passenger side of the vehicle.) Put the corresponding new wiper blade in
place and clip it.
) Fold down the wiper arm carefully.
Before removing a front
wiper blade
)Within one minute after switching off theignition, operate the wiper stalk to position
the wiper blades in the ver tical position. This position must be used in order to avoiddamaging the wiper blade and the bonnet.


After fitting a front wiper
blade
)
Switch on the ignition. )
Operate the wiper stalk again to park the
wiper blades.
Procedure for replacin
g a worn wiper blade with a new one without the use of tools.

Practical information
180
To w i ng your vehicle
)On the front bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar.)Place the gear lever in neutral (position Nfor an electronic or automatic gearbox).
)On the rear bumper, unclip the cover by pressing at the bottom. )Screw the towing eye in fully. )Install the towing bar. )Switch on the hazard warning lamps on both vehicles.)Move off gently and drive for a shor tdistance only.


To w i ng another vehicle
Failure to obser ve this special condition could result in damage to cer tain components (braking, transmission...) and the absence of braking assistance the next time the engine is star ted.
)
Unlock the steering by turning the key one
notch in the ignition switch and release the
parkin
g brake.) Switch on the hazard warning lamps onboth vehicles. )
Move off gently and drive for a shor t
distance only.