rfj Citroen C4 2005 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine 67
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Engine: RFJ
B1GP08WCB1DP05BC
IMPERATIVE: Respect the tightening sequence.
Cylinder head
(22) Crankshaft bearing cap screws
(24) Con rod cap screws(21) Flywheel screw(18) Coolant pump screw
B1CP0GCC
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 67

Downloaded from www.Manualslib.com manuals search engine 68
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
26 Oil gauge screw 1 ± 0,2
27 Oil filter support screw 0,8 ± 0,1
28 Anti-emulsion plate fixing screw 1,9 ± 0,3
29 Oil level sensor fixing screw 1 ± 0,2
30 Drain plug 3,4 ± 0,3
31 Oil sump screw 0,8 ± 0,1
32 Oil pressure switch 2 ± 0,2
33 Oil strainer fixing nuts 0,8 ± 0,1
34 Oil strainer stud 0,6 ± 0,1
Coolant pump screw
35Pre-tightening0,7
Tightening1 ± 0,1
Engine: RFJ
B1BP35NP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 68

Downloaded from www.Manualslib.com manuals search engine 69
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Timing
Exhaust camshaft pulley screw
36Pre-tightening3 ± 0,5
Tightening8,5 ± 0,5
37 Cap 1,1 ± 0,1
Inlet camshaft pulley screw
38Pre-tightening2 ± 0,2
Tightening11 ± 1
39 Tensioner roller screw 2,1 ± 0,2
Guide roller screw
40Pre-tightening1,5 ± 0,1
Tightening3,7 ± 0,7
Engine: RFJ
B1EP1GJP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 69

Downloaded from www.Manualslib.com manuals search engine 70
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Accessories
41 Accessories support fixing stud 0,8 ± 0,1
Accessories support fixings
42Pre-tightening1 ± 0,1
Tightening1,9 ± 0,2
43 Alternator top fixing screw 4,1 ± 0,5
44 Alternator power circuit fixing nut 1,7 ± 0,2
45 Aircon compressor fixing screw 2,3 ± 0,3
46 Alternator bottom fixing screw 4,9 ± 0,5
47 Screw for fixing the automatic tensioner roller
for the accessories drive belt2 ± 0,2
Engine: RFJ
B1BP35PP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 70

Downloaded from www.Manualslib.com manuals search engine 148
ENGINESPECIAL FEATURES - CYLINDER HEAD TIGHTENING
Engines all types
B1DP05BC
Cleaning to be carried out just prior to refitting the cylinder head.
WARNING: Clean the contact faces with the approved CITROËN cleaning product.
Do not use abrasives or cutting tools on the contact faces.
The contact faces must not bear any traces of impact or scratching.
Insert a tap in the threads of the holes in the cylinder block receiving the cylinder head bolts.
Brush the threads of the cylinder head bolts..
Oil the threads and under the heads of the bolts, usingMOLYKOTE G RAPID PLUS.
EnginesTightening Cylinder head bolts
(m.daN)(Max. reusable length in mm)
NFUTightening2 ± 0,2
Angular tightening260° ± 5°122 ± 0,3
Pre-tightening1,5 ± 0,2
KFUTightening2,5 ± 0,2 119
Angular tightening200° ± 5°
6FZ - RFNPre-tightening1,5 ± 0,1
147
Tightening5 ± 0,1
RFJAngular slackening360° ± 2° 127,5 ± 0,5
Tightening2 ± 0,75
RFKAngular tightening285° ± 5° 144,5 ± 0,5
NOTE: Tightening of the cylinder head after a repair is prohibited.
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 148

Downloaded from www.Manualslib.com manuals search engine 152
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
TU
JP
3
J410
A J4S
Engine type
C4
XSARA
XSARA PICASSO
See pages:
KFW KFU NFV NFU 6FZ RFJ RFN RFK
XX XXX
XX X
XX X
155 156 to 157 158 156 to 157 160 162 161 163 162 164EW
5
J4 7 ETTUJP4 J4JP+
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 152

Downloaded from www.Manualslib.com manuals search engine 161
ENGINE
B1EP1FUD
B1EP1FVC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFJ
Tool.
[1]«Junior» T extension: (-).1608.E
Removing.
Engage tool [1]in the notch «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Remove the auxiliaries drive belt.
Carefully release the tensioner roller (1)to reach its minimum.
Remove tool[1].
IMPERATIVE: Check that the roller (1) turns freely
(without play and without tight spots).
Refitting.
If removing the auxiliaries drive belt tensioner roller, tighten the screws 2 ± 0,2 m.daN.
Engage tool [1]in the notch at «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Position the
(new)auxiliaries drive belt, in the following sequence:
- Auxiliaries drive pulley (4), aircon compressor pulley (3), tensioner roller (1)and alternator pulley (2).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves of
the various pulleys.
Release the tensioner roller (1).
Remove tool [1].
Checking the tension of the auxiliaries drive belt.
Check the tension of the auxiliaries drive belt:
- Mark «b»at the level of mark «c», new belt.
- Mark «b»at the level of mark «d», belt to be changed.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 161

Downloaded from www.Manualslib.com manuals search engine 181
ENGINE
CHECKING AND SETTING THE VALVE TIMING
TU
JP
3
J410
A J4S
Engine type
C4
XSARA
XSARA PICASSO
See pages:
KFW KFU NFV NFU 6FZ RFJ RFN RFK
XX XXX
XX X
XX X
185 to 187 188 to 192 185 to 187 197 to 202 193 to 196 217 to 223 103 to 209 210 to 216 217 to 223 224 to 231EW
5
J4 7 ETTUJP4 J4JP+
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 181

Downloaded from www.Manualslib.com manuals search engine 203
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Tools.
[1]Camshaft pinion peg: (-).0194.A
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Disconnect the battery.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel, the plastic pins holding the splash-shield, the splash-shield itself.
A:Pegging on the manualgearbox.
B:Pegging on the automaticgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
B1BP2V3D
B1BP38VC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 203

Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Peg the crankshaft, using tool [2].
Suspend the engine, using a workshop hoist.
Remove the RH engine support, the upper timing cover.
Peg the camshaft pulleys, using tool [1].
NOTE:The pegs [1]should go in without forcing.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and tensioning
the timing belt
(see corresponding operation).
Refitting.
Remove tools [1]and [2].
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B1BP2V3D
B1BP38VC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 204