Exhaust Citroen C4 2005 2.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Crankshaft
Bearing cap fixing screws
Pre-tightening2,5 ± 0,2
Angular tightening60°±5°
Con rod nuts
Pre-tightening2 ± 0,2
Angular tightening70°±5°
Accessories drive pulley hub
Pre-tightening4 ± 0,2
Angular tightening51°±5°
Cylinder block
Piston skirt spray jet1 ± 0,1
Sump1,6 ± 0,1
Timing belt guide roller4,3 ± 0,4
Timing belt tensioner roller2,5 ± 0,2
Cylinder head
Camshaft bearing covers1 ± 0,1
Exhaust manifold2 ± 0,2
Valve cover0,8
Camshaft / hub4,3 ± 0,4
Camshaft pinion / camshaft hub2 ± 0,2 Engines: RHY - RHZ
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 135

Downloaded from www.Manualslib.com manuals search engine 138
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder head
Exhaust manifold
1Pre-tightening1,5
Tightening3 ± 0,3
2 Turbocompressor 2,5 ± 0,2
3 Exhaust clip 2,5 ± 0,5
Cylinder head bolts (*)
Pre-tightening2,2 ± 0,2
4Tightening6 ± 0,5
Slackening1 Turn
Tightening6 ± 0,5
Angular tightening220° ± 5°
Engine: RHR
B1DP1LCPB1DP1LDC
(*) (4) Sequence of tightening
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 138

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 193
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Belt tension measuring instrument: 4122-T
[2]Flywheel locating peg: 4507-T.A
[3]Camshaft pulley locating peg, exhaust: 4533-T.A C2 Tool kit 4507-T
[4]Camshaft pulley locating peg, inlet: 4533-T.A C1
[5]Tensioning tool: 4707-T.J
Checking the valve timing.
Peg the flywheel using the tool [2].
Peg the exhaust camshaft pulley [3].
Peg the inlet camshaft pulley [4].
Setting the valve timing.
Peg the flywheel using the tool [2].
Peg the camshaft pulleys[3]and [4].
B1EP11CC
B1EP11BC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 193

Downloaded from www.Manualslib.com manuals search engine 195
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Turn the two pulleys (1)clockwise to the end of the slots.
With the belt strip (e)fully tensioned, place the belt over the pulley, first exhaust side, then inlet side, while
ensuring that marks (b)and (c)on the belt are aligned with marks (f)on the pulleys.
Hold the belt in this position and engage it over the water pump pinion and the tensioner roller.
Fit the tool [1] on the belt at (e).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction, to obtain: 63 SEEMunits.
Tighten the roller (2)to 2 m.daN.
Tighten the six screws (5)to 1 m.daN.
Essential: Check that:
- The camshaft pulleys (1)are not at the end of the slots
(by removing a screw).
- The markings on the belt are aligned with the markings on the crankshaft and camshaft pulleys.
If not, repeat the setting procedure.
B1EP11GC
B1EP11FC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 195

Downloaded from www.Manualslib.com manuals search engine 201
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Refitting.
Fit the
(new)timing belt in position, in the following order:
- Inlet camshaft pulley, exhaust camshaft pulley, guide roller, crankshaft pulley, position tool [5],
coolant pump pulley, dynamic tensioner roller.
Remove tools [1], [2a], [2b]and [4].
Overtension on the belt.
Turn the tensioner roller (7)with the aid of a hexagonal spanner at «a».
Bring the index «c»to position «d», to tension the belt to the maximum of the interval indicated.
Hold the tensioner roller, using tool [4].
Tighten the fixing nut of the tensioner roller, tightening to 1 m.daN.
Turn the crankshaft by 4 rotations
(normal direction of rotation).
IMPERATIVE: Never make the crankshaft rotate backwards.
Make sure that the timing is correctly set by refitting the pegs [1], [2a]and [2b].
Remove the pegs [1], [2a], [2b]and[4].
B1EP1DPC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 201

Downloaded from www.Manualslib.com manuals search engine 207
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Checking and setting the timing (continued).
Refitting.
Turn the tensioner roller (9), using tool [5a]to go past the notch «b».
Position the tool [5b] to lock the index «a»and remove the tool [5a].
NOTE: Check the presence of the crankshaft pinion keyway (12)before positioning the timing belt.
Reposition the timing belt (8)on the crankshaft pinion (1).
Hold the timing belt in place (8)using tool [3].
Put the timing belt (8)in place, in the following sequence:
- Guide roller (11).
- Inlet camshaft pulley (7).
- Exhaust camshaft pulley (6).
- Coolant pump (13).
- Tensioner roller (9).
NOTE: Make sure that the timing belt (8)is as flush as possible with the outer faces of the various
pinions and rollers.
Remove tools[3], [1]and [5b].
Refit the lower timing cover (5), the pulley (2)and the screw (3)of the crankshaft pulley.
Tighten the screw (3)to 4 ± 0,4 m.daN.
Angular tighten 40°±4°, using tool [4].
B1EP1G2D
B1EP1G3C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 207

Downloaded from www.Manualslib.com manuals search engine 214
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFN
Checking and setting the timing (continued).
Refitting.
Turn the tensioner roller (9), using tool [5a]to go past the notch «b».
Position the tool [5b]to lock the index «a»and remove the tool [5a].
Reposition the timing belt (10)on the crankshaft pinion (1).
Hold the timing belt in place (10)using tool [3].
Put the timing belt (10)in place, in the following sequence:
- Guide roller (12).
- Inlet camshaft pulley (7).
- Exhaust camshaft pulley (6).
- Coolant pump (11).
- Tensioner roller (9).
NOTE: Make sure that the timing belt (10)is as flush as possible with the outer faces of the
various pinions and rollers.
Remove tools [3], [1]and [5b].
Refit the lower timing cover (5), the pulley (2)and the screw (3)of the crankshaft pulley.
Tighten the screw (3)to 4 ± 0,4 m.daN.
Angular tighten 53°±4°, using tool [4].
B1EP1G9D
B1EP1GAC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 214

Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing (continued).
A: Pegging on the manualgearbox.
B: Pegging on the automaticgearbox.
Peg:
- The crankshaft, using tool [2].
- The camshaft pulleys (5)and (6), using tool [1].
Remove:
- The screw (3)of the crankshaft pulley (2).
- The lower timing cover (4)
(by moving the engine).
IMPERATIVE: Never remove the crankshaft pulley (2) without pegging the crankshaft
and the camshafts.
Slacken the screw (9)of the tensioner roller (8).
Turn the tensioner roller (8)
(clockwise).
Remove the timing belt (7).
IMPERATIVE: Systematically replace the following components: timing belt, exhaust
manifold fixing nuts, timing belt tensioner roller nut.
B1BP2V3DB1EP1BBD
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 220

Downloaded from www.Manualslib.com manuals search engine 221
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing (continued).
Turn the tensioner roller (8), using tool [5a]to go beyond slot «b».
Position the tool [5b]to lock the index «a»and remove the tool [5a].
Reposition the timing belt (7)on the crankshaft pulley.
Hold the timing belt (7)in place using tool [3].
Fit the timing belt (7)in place, respecting the following order:
- Guide roller (10).
- Inlet camshaft pulley (6).
- Exhaust camshaft pulley (5).
- Coolant pump (11).
-Tensioner roller (8).
NOTE:Make so that the belt (7)is as flush as possible with the exterior face of the various
pinions and rollers.
Remove:
- Tool [3].
- Tool [1]from the exhaust camshaft pulley.
- Tool [5b]from the tensioner roller (8).
Refit:
- The lower timing cover (4)
(by moving the engine).- The crankshaft pulley (2).
- Screw (3)of the crankshaft pulley.
Tighten screw (3) to 4 ± 0,4 m.daN, then angular tighten to 53°±4°, tool [4].
B1EP1BCDB1EP1BDC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 221