Exhaust Citroen C4 2005 2.G Service Manual

Downloaded from www.Manualslib.com manuals search engine 297
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Tool.
[1]Manual pressure-vacuum pump: FACOM DA 16
Checks.
Vacuum pump.
Connect the tool [1]into the vacuum pump (1).
Start the engine.
The vacuum value should be 0.9 ± 0.1 barat idle
(after 30 secondsof operation).
NOTE:The exhaust gas recycling valve is not linked to the air supply circuit.
The exhaust gas recycling electrovalve is controlled by the engine ECU.
Turbocharging pressure regulation valve.
Connect the tool [1]on the valve (2).
Apply a vacuum of approx. 0.8 bar.
Rod "a"should move 6 ± 2 mm.B1HP1UGC
B1HP22RC
Engine: 9HX
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 297

Downloaded from www.Manualslib.com manuals search engine 298
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Tool.
[1]Manual pressure-vacuum pump: FACOM DA 16
Checks.
Vacuum pump.
Connect the tool [1]into the vacuum pump (1).
Start the engine.
Wait 30 seconds.
The vacuum value should be 0.9 ± 0.1 barat idle.
NOTE:The exhaust gas recycling valve is not linked to the air supply circuit.
The exhaust gas recycling electrovalve is controlled by the engine ECU.
Turbocharging pressure regulation valve.
Connect the tool [1]on the valve (2)
(tube identified by the colour grey).
Apply a vacuum of approx. 0.8 bar.
Rod "a"should move 12 ± 2 mm.
B1HP1UGC
B1HP1UHC
Engines: 9HY - 9HZ
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 298

Downloaded from www.Manualslib.com manuals search engine 302
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Tool.
[1] Manual pressure-vacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect tool [1] on the capsule take-off (2).
Apply a vacuum of approx. 0,6 barseveral times to activate the rod «a».
In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
Regulation electrovalve (EGR).
Check to be performed between the electrovalve (1)and the EGR valve (2).
Link the tool [1]in series, between the electrovalve (1)and the capsule (2).
Compare the values noted with those in the table below.
Engine speed (rpm) Vacuum value
780 0,5 bar
2500 0 bar
B1HP1K6D
Engines: 8HX - 8HZ
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 302

Downloaded from www.Manualslib.com manuals search engine 303
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Exhaust gas recycling (EGR) valve.
(1)Exhaust gas recycling (EGR) electrovalve
NOTE:The engine ECU pilots the EGR valve.
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
- «INJECTION»menu.
- Actuator tests.
- EGR electrovalve.
Check that you can hear the click from the EGR regulation electrovalve.
Double butterfly housing
(vehicle with particle filter).
(2)Double butterfly housing
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
- «INJECTION»menu.
- Actuator tests.
- Butterfly.
EGR exchanger butterfly.
Check that you can hear the click from the double butterfly housing.
B1HP1UPC
B1HP1UQC
XSARA PICASSO
Engines: 9HZ - 9HY
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 303

Downloaded from www.Manualslib.com manuals search engine 304
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Tool.
[1]Manual vacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
EGR valve.
Connect the tool [1]to the capsule union (1).
Apply, several times in succession, a vacuum of approx. 0.6 barto activate the rod "a".
In abrupt reaction to the vacuum, the valve should close on its seating with a clicking noise.
Exhaust gas reycling (EGR) electrovalve.
Check, not under load, between the electrovalve (2)and the EGR valve (1).
Connect the tool [1]between the electrovalve (2)and the capsule (1).
Compare readings with the values in the table below.
Engine speed (rpm) Vacuum value
780 0,5 bar
2500 0 bar
B1HP12GD
Engines: RHY - RHZ
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 304