ring Citroen C4 2005 2.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine 171
ENGINE
XSARAAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering, with air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (1).
Tighten the screw (2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] at "e".
Tighten the screw (2)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (1)to 2 m.daN.
Remove the tool [1].
B1BP1SGCB1BP1SFC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 171

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172

Downloaded from www.Manualslib.com manuals search engine 173
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Power-assisted steering, without air conditioning (continued)
XSARA
Refitting.
Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1] with the knob downwards.
Tighten the nut (2)to obtain a value of:
Reused belt:
- Keep the value taken at removal.
New belt:
- Tension should be 110 SEEMunits.
- Tighten the screw (1)to 9.5 m.daN.
- Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEMunits.
- Remove the tool [1].
- Start the engine and run it for 10 seconds.
- Stop the engine.
- Place the tool [1]on the belt at "f".
- Tension should be 130 ± 4 SEEMunits.
- Remove the tool [1].
B1BP1SJD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 173

Downloaded from www.Manualslib.com manuals search engine 174
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning
Tools.
[1] Dynamic tensioner peg: (-) 0188 H
[2] Belt tension measuring instrument: 4122-T
Removal.
Peg the dynamic tensioner (1) at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
- Loosen the screw (2)of the roller (3).
- Using a 7 mmsquare drive, turn the roller (3)at "b".
- Peg the tensioner (1) at "a", using tool [1].
NOTE: If the belt is broken:
- Support the engine using a jack
(insert a wooden block between the housing and the jack).
- Remove the right engine support.
- Using a square drive at (b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 174

Downloaded from www.Manualslib.com manuals search engine 175
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning (continued)
Refitting.
Refit the belt.
Using a 7 mmsquare drive at "b", turn the roller (3), until the tool [1] located at "a"becomes
free.
Tighten the screw (2).
Remove the tool [1].
B1BP1SLC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 175

Downloaded from www.Manualslib.com manuals search engine 178
ENGINEXSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning
B1BP1YLD
Tools.
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removal.
Re-use of belt.
WARNING: Mark the direction the belt was fitted in case of re-use of the same belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Hold the tensioner roller (7) compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Peg using tool [2], at «d».
Loosen the screw (6).
Bring the eccentric roller (5)towards the rear.
Tighten the screw (6)by hand.
Remove the belt.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 178

Downloaded from www.Manualslib.com manuals search engine 185
ENGINE
Tools.
[1]Flywheel peg: 4507-T.A
[2] Camshaft pulley peg: 4507-T.B Toolkit 4507-T
[3]Square: 4507-T.J
[4] Belt tension measuring instrument: 4122-T
[5] Valve rocker thrust plate: 4533-T.Z
Checking the timing.
Peg the flywheel, using tool [1].
Peg the camshaft pulley, using tool [2].
Setting the timing.
NOTE:Remove the sparking plugs, to ease rotation of the crankshaft.
Rotate the engine by means of the crankshaft screw (1).
Peg the camshaft pinion.
Peg the flywheel
Slacken the nut (2).
Fullt detension the belt by acting on the tensioner roller.
Remove the belt.
IMPERATIVE: Check that the tensioner roller turns freely
(no tight spot).
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
B1EP067CB1EP066CB1EP068C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 185

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Overtension on the belt.
Position «a»: Tensioner roller in detensionedposition.
Position «b»: Tensioner roller in normalposition.
Position «c»: Tensioner roller in overtensionposition.
Turn the tensioner roller (10), using an allen spanner at «e».
Place the index «d»in position «c», hold the belt to the maximum of the interval indicated.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
Rotate the crankshaft four turns
(normal direction of rotation).
IMPERATIVE: Never turn it backwards.
Check the timing setting by refitting the pegs [1], [2] and [3].
Remove the pegs [1], [2]and [3].
Adjusting the fitting tension of the timing belt.
Slacken the nut, holding the position of the tensioner roller, using an allen spanner at «e».
Bring the index «d»to its adjustment position at «b».
WARNING: The index «d» should not go past the notch «b». If it does, repeat the operation
to tension the timing belt.
Maintain the roller (10)in this position, using an allen spanner.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing. If it
does, repeat the operation to tension the timing belt.
Complete the refitting.
B1EP1DTC
B1EP1DUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 192

Downloaded from www.Manualslib.com manuals search engine 193
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Belt tension measuring instrument: 4122-T
[2]Flywheel locating peg: 4507-T.A
[3]Camshaft pulley locating peg, exhaust: 4533-T.A C2 Tool kit 4507-T
[4]Camshaft pulley locating peg, inlet: 4533-T.A C1
[5]Tensioning tool: 4707-T.J
Checking the valve timing.
Peg the flywheel using the tool [2].
Peg the exhaust camshaft pulley [3].
Peg the inlet camshaft pulley [4].
Setting the valve timing.
Peg the flywheel using the tool [2].
Peg the camshaft pulleys[3]and [4].
B1EP11CC
B1EP11BC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 193