ignition Citroen C4 AIRCROSS 2014 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2014, Model line: C4 AIRCROSS, Model: Citroen C4 AIRCROSS 2014 1.GPages: 368, PDF Size: 20.37 MB
Page 35 of 368
1
33
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Fault with the "Keyless Entry and
Starting" system. Contact a CITROËN dealer.
Fault with the electronic anti-theft
system. Switch off the ignition, then start the
engine. If the problem persists, contact a
CITROËN dealer.
The electronic key is not detected. Insert the electronic key into the
housing located in the glove box. Remember to remove the electronic
key from the housing after starting
the vehicle.
The electronic key has not been
removed from the housing in the
glove box. Remove the electronic key from the
housing in the glove box.
The steering column is locked. Switch the ignition on and turn the
steering wheel slightly to unlock the
steering column.
The engine is off but the gear lever
is not in position P
. Place the gear lever in position P
. Only for vehicles fitted with a "CVT"
gearbox.
Page 37 of 368
1
35
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Warning messages (ignition at "ON")
Fault with the electric power
steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a CITROËN
dealer or a qualified workshop.
The battery for the "Keyless Entry
and Starting" system is flat. Replace the battery (see "Changing
the batteries").
The electronic key that you have on
your person is not recognised. Check that you have the correct
electronic key. If the message persists, contact a
CITROËN dealer.
The electronic key is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that you have the electronic
key on your person before locking
the vehicle.
One of the doors or the boot is not
properly closed when locking the
vehicle from the outside. Close the door or the boot, then
lock the vehicle.
Fault with the "Keyless Entry and
Starting" system. Contact a CITROËN dealer.
Page 38 of 368
36
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
The brake fluid level is too low. Top up using a brake fluid listed by
CITROËN. If the problem persists, contact
a CITROËN dealer or a qualified
workshop.
Fault with the braking system. You must stop as soon as it is safe
to do so. Have the system checked by a
CITROËN dealer or a qualified
workshop.
Fault with the anti-lock braking
system (ABS). Contact a CITROËN dealer or a
qualified workshop. The vehicle retains conventional
braking without assistance but you
are advised to stop.
One of the doors or the boot is not
properly closed. Close the door or the boot. The opening in question is identified
in the screen.
The bonnet is not properly closed. Close the bonnet.
Fault with the electronic anti-theft
system. Switch off the ignition then start the
engine again. If the problem persists, contact a
CITROËN dealer.
The driver's door is open and the
ignition is still on. Switch off the ignition before leaving
the vehicle.
Page 43 of 368
1
41
Monitoring
Screen 1
Screen 2
System
Observations
Information messages (ignition at "ON")
2WD two wheel drive
system
Flashes for a few moments when the "2WD" (2 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD four wheel drive
system
Flashes for a few moments when the "4WD" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD LOCK four wheel
drive system
Flashes for a few moments when the "LOCK" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
Active stability control
(ASC)
Flashes when the stability control system (ASC) is operating.
Page 44 of 368
42
Monitoring
Screen 1
Screen 2
System
Cause
Observations
Solution - Action
Prevention messages
Ser vice indicator
Informs the driver that the
next ser vice is overdue. This is displayed for a few
seconds when the ignition is
switched on. Contact a CITROËN dealer
or a qualified workshop.
Rest reminder
Informs the driver that they
should stop to take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal sounds
3 times and then every
5 minutes until the vehicle
stops. You are advised to take a
break approximately every
two hours.
Page 45 of 368
1
43
Monitoring
Tr i p c o m p u t e r
With the ignition on, each press on the INFO
button displays the following screens in
succession:
- distance recorder and trip recorder A,
- distance recorder and trip recorder B,
- ser vice indicator,
- coolant temperature,
- range,
- average fuel consumption,
- average speed,
- current fuel consumption,
- setting menu,
- any alert messages.
Information display
Distance recorder
System for measuring the total distance
travelled by the vehicle during its life.
The total distance is
displayed in the lower part of
the screen.
Trip distance recorder
(Trip A or B)
Reset to zero
With the ignition on and either trip A
or B
displayed, press the INFO
button for more than
2 seconds. Only the trip displayed will be reset.
Each of these trip recorders
indicates the distance
travelled since the last reset.
Press the INFO
button to
display the desired trip.
Page 46 of 368
44
Monitoring
Service indicator
System which informs the driver when the
next ser vice is due in accordance with the
manufacturer's ser vicing schedule.
The point at which the next ser vice is due is
calculated from the last ser vice indicator zero
reset.
It is determined by two parameters:
- the distance travelled (in miles (km)),
- the time elapsed since the last ser vice
(in months).
The distance remaining to be travelled may be
weighted by the time factor, depending on the
use made of the vehicle.
Example:
the screen indicates that 7300 miles
(kilometres) remain before the next service
is due.
Service overdue
Example:
the screen indicates that the ser vice
is overdue. This ser vice must be carried out by
a CITROËN dealer or a qualified workshop.
Operation
The symbol "--
"
remains displayed until
the first ser vice of a new vehicle has
been carried out. Each time the ignition is switched on, the
"ROUTINE MAINTENANCE REQUIRED"
symbol is displayed for a few seconds to indicate
that the ser vice must be carried out without delay. When the ignition is switched on, you must press
the INFO
button several times in succession
until the ser vice indicator is displayed. The
distance recorder display line indicates the
number of miles or kilometres remaining and
the time elapsed line indicates the number of
months remaining before the next ser vice is due.
Page 47 of 368
1
45
Monitoring
Resetting the service indicator
to zero
After a certain distance and a certain
time, the display of "---
"
is reset
automatically and the display indicates
the time remaining before the next
ser vice is due.
Your CITROËN dealer or a qualified workshop
carries out this operation after each ser vice.
If you have carried out your vehicle's ser vice
yourself, the zero reset procedure is the
following:
)
switch off the ignition,
)
press the INFO
button several times in
succession until the ser vice indicator is
displayed,
)
press and hold the INFO
button for a few
seconds until the spanner flashes
,
)
press the INFO
button while the spanner
is flashing to change the display "---
"
to
"CLEAR"
then the time remaining before
the next service is due is displayed.
Page 49 of 368
1
47
Monitoring
Average fuel consumption
(l/100 km or km/l or mpg)
This is the average fuel
consumption calculated
since the trip computer was
last reset.
Average speed
(km/h or mph)
This is the average speed
calculated since the trip
computer was last reset.
Current fuel consumption
(l/100 km or km/l or mpg)
This is the average fuel
consumption calculated over
the last few seconds.
This value may change following a
change in the style of driving or the relief.
If dashes "- - -" are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer or a
qualified workshop.
Resetting the information to zero
When the required information is displayed,
press the INFO
button for more than
two seconds to reset all of the information to
zero.
When the ignition is switched on, the zero reset
switches automatically from manual mode to
automatic mode.
Automatic
If the ignition key remains in the OFF position
for more than 4 hours, the information is reset
to zero automatically.
Page 50 of 368
48
Monitoring
The various menus may change between
the type 1 instrument panel and the type 2
instrument panel.
Adjusting vehicle settings
When the vehicle is
stationary
, it allows the
user to change the following
settings:
- the reinitialisation
mode for average
fuel consumption and
average speed,
)
Press and hold the INFO
button for a few
seconds to display the menu screen.
)
In the menu screen, press the INFO
button
to select a function from the list:
- the fuel consumption units,
- the temperature display unit,
- the display language,
- activation/deactivation of the sound when
pressing the INFO
button,
- the break (rest) reminder display inter val,
- restore the factory settings.
To change the settings, you must stop
the vehicle and switch on the ignition.
Apply the parking brake and place the
gear lever in neutral.
With the ignition on
, press the INFO
button
on the dashboard, to the left of the instrument
panel, several times in succession until the
"SETTINGS MENU" screen is displayed.
Operation
MENU
1/3
:
- 1 - 2, A - M, A - P
* (choice of the type of
reset of average fuel consumption and
average speed),
- AVG UN I T
(choice of the fuel consumption
units),
- choice of the temperature display unit
,
- LANGUAGE
(option of the display
language),
*
According to display language.
For your safety, when the vehicle is
moving
, the function settings are not
displayed when you press the INFO
button.