top Citroen C4 PICASSO 2008 1.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C4 PICASSO, Model: Citroen C4 PICASSO 2008 1.GPages: 266, PDF Size: 7.14 MB
Page 107 of 266
III
105
A U T O M A T I C A I R C O N D I T I O N I N G
(Function for retaining ventilation with the engine switched off : REST function, continued…)
Engine stopped, ignition switched on :- The displays will light up, with the air blower shown empty as long as the function is available.- A press on the REST button activates the function for a timing of just a few minutes. Two blades of the b l o w e r w i l l fi l l t o s i g n i f y t h a t t h e f u n c t i o n i s a c t i v e .- It can be deactivated and reactivated during the timing.- At the end of the timing, the display will go off.
On stopping the engine :- The displays remain lit up, the blower is shown em pty and the function can be activated for 30 seconds.- A press on the REST button during the next 30 sec-onds activates the function for a timing of several min-utes. The duration and availability of the function are variable according to the state of charge of the battery (a protection to guarantee engine starting). Two blower b l a d e s fi l l u p t o s i g n i f y t h a t t h e f u n c t i o n i s a c t i v e . I t r e -mains active, even after the doors have been locked , until the end of the timing. - A f u r t h e r p r e s s b e f o r e t h e e n d o f t h e t i m i n g d e fi n i t i v e l y stops the function.
Note : This button does not activate the air conditioning, o n l y t h e a i r b l o w e r s . I n t h e R E S T f u n c t i o n , t h e a i r fl o w a n d distribution are controlled automatically and you c annot modify them.
4 - Adjustment of the air distribution- Press on button 4 s o t h a t t h e a i r fl o w s s c r o l l s u c c e s -sively on the display.
5 - Air recirculation
This button activates the recirculation of air within the passenger compartment and also has an automatic function.
The air distribution you have chosen is con- fi r m e d b y t h e l i g h t i n g o f t h e c o r r e s p o n d i n g warning lamps in the display.
There are 7 possible adjustments.
Entry of air in automatic mode (activated by default, in automatic comfort regulation)
Automatic mode makes use of an air quality sensor. This analyses the air and isolates the passenger com-partment from the exterior as soon as it detects the presence of pollutants. Then it automatically activates recirculation of cabin air.
1
Closing of the air inlet
- Press on button 5 to close off the entry of air from outside.2
Whilst retaining the other adjustments, this position enables the driver at any time to exclude any disa-greeable odours or fumes coming from outside the vehicle.
It should be cancelled as soon as possible to permit renewal of cabin air and to prevent misting.
- Press once on button 5 to return to the initial status (entry of air in automatic mode).
Note : The airrecirculation can also be accessed by means of a press on the control located low down to one side of the steering wheel (see “Fixed centred controls steering wheel").
Entry of air (manual mode)
- Press on button 5 to activate entry of air from the outside. The warning lamp goes out. 3
Page 108 of 266
106
III
A U T O M A T I C A I R C O N D I T I O N I N G
6 - Adjustment mode for the rear passengers8 - Deicing / demisting of the rear screen
This can only operate when the engine is running.
- Press on button 8 to activate/deactivate the electric deicing of the rear screen and, according to version, of the exterior rear view mirrors. The warning lamp lights up and the symbol appears on the display.
It switches off automatically to prevent excessive con-sumption of power
9 - Rapid deicing / demisting of the front and rear windows
- Press on button 9. The warning lamp lights up.
This button decides whether or not the rear passengers may use their adjustment controls.
There are three possible statuses for this button :
Locking of the rear passenger controlsThe driver imposes his adjustment on the rear passengers.
Authorisation of the rear passenger controls
The rear passengers can use their adjustment controls at their conven-ience.
C l o s i n g o f t h e a i r fl o w f o r t h e r e a r passengers
The supply of air is cut off.
7 - Panel display mode : black panel function
This function turns the displays and panel backlighting on or off.
- Function activated, a press on any button will light up the screen temporarily.
- A press on button 7 deactivates the function, lighting of buttons and screen is again permanent.
Note : This function optimises notably the visual com-fort for driving at night.
This function gives a rapid deicing / demisting of the vehicle simultaneously with :
- front deicing at optimum temperature,
- o p t i m u m a i r fl o w ,
- recirculation prohibition,
- deicing of the rear view mirrors and heated rear screen,
- air conditioning, if necessary.
Press again on button 9 or on " AUTO " to stop the function. Deicing of the rear view mirrors and heated rear screen remains activated.
10 - Air conditioning
- Press on button 10 to activate the air conditioning.
The A/C warning lamp lights up.
With additional air conditioning, in cold weather you are advised to close the supply of air to the rear pas-sengers (no hot air distribution possible via these air vents).
Page 112 of 266
110
III
Head restraint
To raise it, pull it upwards. To lower it, press on the control as well as on the head restraint. The adjustment is correct when the top of the head restraint is level with the top of the head. It can also be adjusted for tilt.
To remove it, press on the unlocking button and pull it up-wards.
To adjust the head restraint fore/aft, move the base of the head restraint to obtain the position desired.
Note : N e v e r d r i v e w i t h o u t t h e h e a d r e s t r a i n t s fi t t e d .
Backrest angle
Action the control and adjust the angle of the backrest.
It is possible to incline the backrest 45° rearwards by tilting it until it locks ; to unlock it, lift the control.
Seat height adjustment
Raise or lower the the control the number of times necessary to obtain the position desired.
Lumbar support
Rotate the control until you attain the position desired.
Longitudinal adjustment
Raise the control bar, then slide the seat to the positio n desired.
Armrest
To adjust the position of the armrest, pull it up and then fully down, and then raise it to the desired position.
F R O N T S E A T S M A N U A L A D J U S T M E N T S
Page 113 of 266
1
2
III
111
Heated seats
The front seats can be heated independently. Use the controls on the inner sides of the seats and choose one of the three heat intensities below
0 : Off.
1 : Slight heat.
2 : Medium heat.
3 : Strong heat.
The seat temperature will adjust automatically.
Note : the heated seats only func-tion when the engine is running.
Note : The seats can also be adjusted on a temporary basis :
- on opening one of the front doors.
- after switching off the ignition.
Electric adjustments :
Adjustment of seat height and angle, longitudinal adjustment
Adjustment of backrest angle and lumbar support
Raise or lower the front of control 1 to raise or lower the front of the seat base (on driver’s seat).
Raise or lower the rear of control 1 to raise or lower the seat.
Action control 1 forwards or rearwards to slide the seat forwards / backwards.
Push the top of control 2 forwards or rearwards to adjust the backrest angle.
Raise or lower control 2 to increase or decrease the lumbar support.
F R O N T S E A T S E L E C T R I C A D J U S T M E N T S
Page 116 of 266
A
B
12
114
III
LONGITUDINAL ADJUSTMENT
Lift the control A, located at the front of the seat, then adjust the seat into the position desired.
THE “COMFORT" POSITION
The 3 second-row seats are inde-pendent of each other and all the same width. They all can have a “comfort" position.
To place the seat(s) in the comfort position
- Pull on the control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to the initial position
- Pull on the control B and allow the seat to come forwards.
IMPORTANT : Always supervise any movements of seats by chil-dren.
REAR HEAD RESTRAINTS
The rear head restraints have two possible positions :
1. a low position for when the seats are not occupied,
2. a high position to ensure pas-senger safety, by raising the restraints to their locking posi-tion.
To lower the head restraints
- Press on the unlocking button.
- Press on the top of the head restraint.
To raise the head restraints
- Pull the head restraint upwards as far as it will go.
- Press on the unlocking button and pull the head restraint up-wards.
S E C O N D R O W S E A T S
Page 118 of 266
A
B
12
114
III
LONGITUDINAL ADJUSTMENT
Lift the control A, located at the front of the seat, then adjust the seat into the position desired.
THE “COMFORT" POSITION
The 3 second-row seats are inde-pendent of each other and all the same width. They all can have a “comfort" position.
To place the seat(s) in the comfort position
- Pull on the control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to the initial position
- Pull on the control B and allow the seat to come forwards.
IMPORTANT : Always supervise any movements of seats by chil-dren.
REAR HEAD RESTRAINTS
The rear head restraints have two possible positions :
1. a low position for when the seats are not occupied,
2. a high position to ensure pas-senger safety, by raising the restraints to their locking posi-tion.
To lower the head restraints
- Press on the unlocking button.
- Press on the top of the head restraint.
To raise the head restraints
- Pull the head restraint upwards as far as it will go.
- Press on the unlocking button and pull the head restraint up-wards.
S E C O N D R O W S E A T S
Page 136 of 266
A
B
D
C
III
133
The ISOFIX anchoring system
T h e t h r e e s e c o n d - r o w r e a r s e a t s a s w e l l a s t h e f r o n t p a s s e n g e r s e a t p o s i t i o n o n y o u r v e h i c l e a r e e q u i p p e d w i t h t h e r e g u l a t i o n I S O F I X a n c h o r i n g p o i n t s .
T h e r e a r e 3 r i n g s f o r e a c h s e a t p o s i t i o n : - T w o “ b o t t o m ” r i n g s A and B , b e t w e e n t h e s e a t c u s h i o n a n d t h e b a c k r e s t . T h e y a r e a p p r o x . 2 8 c m a p a r t . - A “ t o p ” r i n g C, behind a cover at the top of the backrest f o r t h e s e c o n d - r o w s e a t s , a n d a t t h e b o t t o m r i g h t o f t h e s e a t b a s e f o r t h e f r o n t p a s s e n g e r s e a t p o s i t i o n .
I S O F I X c h i l d s e a t s h a v e t w o l a t c h e s w h i c h a r e e a s y t o a t t a c h o n t h e t w o “ b o t t o m ” r i n g s A and B.
Top ring C
1. T o a t t a c h t h e t o p r i n g , u n c l i p t h e c o v e r D.
2. Raise the head restraint of the vehicle seat, then p a s s t h e a t t a c h m e n t b e t w e e n t h e u p r i g h t s .
3. N e x t s e c u r e t h e a t t a c h m e n t o n t h e “ t o p ” r i n g C ( s e c o n d r o w s e a t s ) .
4. Tension the top belt.
T h i s fi x i n g s y s t e m i s d e s i g n e d f o r c h i l d r e n w e i g h i n g u p t o 1 8 k g .
C H I L D R E S T R A I N T S
Page 144 of 266
A
A
III
141
The scented air freshener releases a f r a g r a n c e i n t o t h e p a s s e n g e r c o m -partment via the central air vents.
The air freshener contains an e m p t y c a r t r i d g e w h e n y o u r v e h i c l e is delivered. You therefore need to i n s e r t a c a r t r i d g e i n o r d e r t o u s e the air freshener.
A d j u s t m e n t o f fl o w- Rotate the button A to adjust ( t o t h e l e f t t o r e d u c e , t o t h e r i g h t t o i n -crease) or stop ( m a x i m u m t o t h e left) t h e fl o w o f s c e n t e d a i r .
Note : the central air vents have to be open.
A c a r t r i d g e l a s t s o n a v e r a g e 3 months, based on 1 hour’s us- a g e p e r d a y .
To remove the air freshener
1. Press the button A , r o t a t i n g i t a q u a r t e r t u r n t o t h e l e f t a s f a r a s i t w i l l g o .
2. Remove the air freshener from the dashboard.
3. R e p l a c e t h e c a r t r i d g e ( s e e “ C h a n g i n g t h e c a r t r i d g e ” ) .
To insert the air freshener
A f t e r fi t t i n g o r c h a n g i n g a c a r t r i d g e :
1. Place the air freshener back in i t s h o u s i n g .2. R o t a t e i t a q u a r t e r t u r n t o t h e r i g h t .
S C E N T E D A I R F R E S H E N E R
Page 148 of 266
III
145
MODUBOX
The Modubox is for use both inside the vehicle and a w a y f r o m t h e v e h i c l e . I t i s c o m p o s e d o f a s h o p p i n g t r o l l e y a n d a fl e x i b l e b a g ( i s o t h e r m o n s o m e v e r s i o n s ) w h i c h c a n b e u s e d i n d e p e n d e n t l y o f e a c h o t h e r d e - p e n d i n g o n y o u r n e e d s ( b y d e t a c h i n g t h e f a s t e n i n g s on each side at the top and bottom).
To use
1. U n h o o k t h e r e d s t r a p t o f r e e t h e M o d u b o x .
2. U n h o o k t h e b l a c k s t r a p t h e n p r e s s o n t h e r o u n d buttons on either side of the Modubox simultane- o u s l y t o d e p l o y i t .
B O O T M O D U B O X - C 4 P I C A S S O
U s e o f t h e M o d u b o x o u t s i d e t h e v e h i c l e
- Press on the recess on the left hand side of the M o d u b o x t o r a i s e ( o r l o w e r ) t h e h a n d l e .
Stowage inside the vehicle
- P e r f o r m t h e o p e r a t i o n s i n r e v e r s e t o f o l d a n d s t o w inside the vehicle.
- I f y o u h a v e u s e d y o u r M o d u b o x a w a y f r o m t h e v e h i c l e , t a k e c a r e t o r e p o s i t i o n i t c o r r e c t l y i n t h e h o u s i n g s p r o -vided for this purpose.
Page 159 of 266
IV
R A D I O S O U R C E
Notes on radio reception
Your radio will be subject to certain phenomena that are not encoun-tered by domestic systems.
The reception of AM and FM sig-nals may suffer from interference, which is caused by the nature and propagation of the signals and d o e s n o t r e fl e c t o n t h e q u a l i t y o f your radio installation.
In AM, the reception may be af-fected when passing under power lines or bridges, or when travelling through tunnels.
In FM mode, the reception may be affected by the distance from the s t a t i o n t r a n s m i t t e r , t h e r e fl e c t i n g o f signals off obstacles (mountains, hills, tower blocks) and radio blacks-pots (no coverage from the station transmitter).
Selection of radio source
Press button D to select the source.
Selection of frequencies and memory banks
Press button E successively to go through the memory banks FM1, FM2 and FM3, for the FM wave-band, and the memory banks MW/LW, for the AM waveband.
Manual search
Manual search is via buttons J or M.
By keeping button J or M pressed, you will be able to scroll through the waveband. Scrolling will stop as soon as you release the button. The radio will remain tuned to the frequency that is displayed.
Tuning sensitivity
Automatic searches can be car-ried out according to two levels of sensitivity :
- To capture the most powerful trans-mitters, choose the local search mode “LO” (default option).
- To capture the weakest or most distant transmitters, choose the sensitive search mode “DX”.
S e a r c h f o r a s t a t i o n i s d o n e fi r s t in “LO” (local) sensitivity, then in “DX” (distant) sensitivity.
To commence a search in sensi-tivity “DX” (distant) immediately , press twice in succession on one of the buttons K or N.
Automatic search
A short press on one of the but-tons K or N will tune into higher or lower radio stations respectively, within the chosen waveband.
By keeping button K or N pressed, you will be able to scroll through the waveband. The scrolling will s t o p a t t h e fi r s t s t a t i o n i t fi n d s o n c e the button is released.
You can also do this by means of control 2 at the steering wheel.
If the automatic search is unable to tune into a known frequency (perhaps owing to very weak re-ception), it is possible to search m a n u a l l y t o fi n d t h i s s t a t i o n .
Display and selection of a station available in the area in which you are travelling
B r i e fl y p r e s s o n b u t t o n G to bring up a list of stations, this is updated every 10 minutes.
You can also update this list at any time by giving a long press on button G.
To listen to one of these stations, select by pressing buttons J or Mand validate using button L.