engine Citroen C4 PICASSO RHD 2014.5 1.G Manual PDF

210
Courtesy lamps
1. Front courtesy lamp
2.
F ront map reading lamps
3.
R

ear courtesy lamp
4.

R
ear map reading lamps
Front - rear courtesy lamps
F With   the   ignition   on,   press   the  c
orresponding s witch.
Front - rear map reading
lamps
With the "permanent lighting" mode, the lighting time   varies   according   to   the   circumstances:
-
 
w
ith   the   ignition   off,   approximately
 t

en minutes,
-
 
i
n   energy   economy   mode,   approximately
 t

hirty   seconds,
-
 
w
ith   the   engine   running,   unlimited.
In this position, the courtesy lamp comes   on   gradually:
Permanently
  off.
Permanent
 l

ighting.
-
 
w

hen
  the   vehicle   is   unlocked,
-
 
w

hen
  the   electronic   key   is   removed   from  
t

he
 r

eader,
-
 
w

hen
  opening   a   door,
-
 
w

hen
  the   remote   control   locking   button   is  
a

ctivated,   in   order   to   locate   your   vehicle.
It
 
switches   off   gradually:
-
 
w

hen
  the   vehicle   is   locked,
-
 
w

hen
  the   ignition   is   switched   on,
-
 
3

0
 
seconds   after   the   last   door   is   closed.Take
  care   to   avoid   leaving   anything  
in
  contact   with   the   courtesy   lamps.
Depending
 o

n
 v

ersion, you can
also switch the
courtesy
  lamp   on   or  
o

ff   by   pressing   this  
b

utton.
Visibility

218
Electronic Stability Control (ESC) incorporating the   following   systems:
-
 
a
nti-lock   braking   system   (ABS)   and   the  
e

lectronic   brake   force   distribution   (EBFD),
-
 
e
mergency   braking   assistance   (EBA),
-
 
w
heel   anti-slip   regulation   (ASR)   or   traction  
c

ontrol,
-
 
d
ynamic   stability   control   (DSC).
Electronic stability control (ESC)
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
This system improves the stability and manoeuvrability   of   your   vehicle   when   braking  
a

nd   contributes   towards   improved   control   in  
c

orners,   in   particular   on   poor   or   slippery   road  
su

rfaces.
The
  ABS   prevents   wheel   lock   in   the   event   of  
em

ergency
 b
raking.
The
  electronic   brake   force   distribution   system  
m

anages   the   braking   pressure   wheel   by   wheel.
Emergency braking assistance
(EBA)
In an emergency, this system enables you to reach   the   optimum   braking   pressure   more  
q

uickly   and   therefore   reduce   the   stopping  
di

stance.
It
  is   triggered   according   to   the   speed   at   which  
t

he   brake   pedal   is   pressed.   This   is   felt   by   a  
r

eduction   in   the   resistance   of   the   pedal   and   an  
i

ncrease   in   the   effectiveness   of   the   braking.
Anti-slip regulation (ASR)
The ASR system (also known as Traction Control)   optimises   traction   in   order   to   limit  
w

heel   slip   by   acting   on   the   brakes   of   the   driving  
w

heels   and   on   the   engine.   It   also   improves  
t

he   directional   stability   of   the   vehicle   on  
a

cceleration.
Dynamic stability control (DSC)
If there is a difference between the path followed   by   the   vehicle   and   that   required   by  
t

he   driver,   the   DSC   monitors   each   wheel   and  
a

utomatically   acts   on   the   brake   of   one   or   more  
w

heels   and   on   the   engine   to   return   the   vehicle  
t

o   the   required   path,   within   the   limits   of   the   laws  
o

f   physics.
Safety

220
Dynamic stability control (DSC)
and anti-slip regulation (ASR)Activation
These systems are activated automatically each   time   the   vehicle   is   started.
As
  soon   as   they   detect   a   problem   of   grip   or  
t

rajectory,   these   systems   act   on   the   operation   if  
t

he   engine   and   brakes.
Deactivation
In exceptional conditions (starting a vehicle which   is   bogged   down,   stuck   in   snow,   on   soft  
g

round...),   it   may   be   advisable   to   deactivate  
t

he   DSC   and   ASR,   so   that   the   wheels   can   turn  
f

reely   and   regain   grip.
This
 
is
 
indicated
 
by
 
flashing
 
of
 
this
 
w

arning
 
lamp
 
in
 
the
 
instrument
 
panel. Reactivate
  the   systems   as   soon   as   the   level   of  
g

rip   permits. F
 
P
ress   this   button.
This
  indicator   lamp   and   the   indicator  
l

amp   in   the   button   come   on.
The
  DSC   and   ASR   systems   no   longer   act  
o

n   the   operation   of   the   engine   and   on   the  
b

rakes   in   the   event   of   a   involuntary   change   of  
t

rajectory.
DSC/ASR
The DSC and ASR systems offer increased s afety   in   normal   driving,   but   they   should   not  
e

ncourage   the   driver   to   take   extra   risks   or   drive  
a

t   high   speed.
It
  is   in   conditions   of   reduced   grip   (rain,   snow,  
i

ce)   that   the   risk   of   loss   of   grip   increases.  
I

t   is   therefore   important   for   your   safety   to  
k

eep   the   DSC   and   ASR   systems   activated  
i

n   all   conditions,   and   particularly   in   difficult  
c

onditions. The
  correct   operation   of   these   systems  
d

epends   on   observation   of   the   manufacturer's  
r

ecommendations   regarding   as   much   the  
w

heels   (tyres   and   rims),   braking   and   electronic  
c

omponents   as   the   assembly   and   repair  
p

rocedures   used   by   CITROËN   dealers.
To   benefit   in   full   from   the   effectiveness   of   the  
D

SC   and   ASR   systems   in   wintry   conditions,  
t

he   vehicle   must   be   fitted   with   four   snow  
t

yres,   allowing   the   the   vehicle   to   retain   neutral  
b

ehaviour   on   the   road.
Safety

225
Seat belt not fastened
and unfastened alerts
Rear seat belts not fastened
alert
The instrument panel includes a seat belt not-
f astened w arning lam p A   as  well  as  an  indicator o

f   the   location   of   the   non-fastened   belts   B.
When
  the   system   detects   a   non-fastened   or  
u

nfastened   seat   belt,   the   warning   lamp   A   come  
o

n   as   well   as   the   corresponding   points   in   the  
i

ndicator   B.
On
  switching   on   the   ignition,   engine   running  
o

r   the   vehicle   at   a   speed   of   up   to   12   mph  
(

20   km/h),   the   warning   lamp   A as well as the
corresponding
  points   in   the   indicator   B   come  
o

n   for   about   thirty   seconds,   if   one   or   more   rear  
p

assengers   have   not   fastened   their   seat   belt.
Seat belts unfastened alert
Front seat belts not fastened
alert
On switching on the ignition, the warning lam p A   comes   on,   as   well   as   the  
c

orresponding points   in   the   indicator   B, if the
driver
  and/or   front   passenger   have   not   fastened  
t

heir   seat   belt. At
  speeds   above   12   mph   (20   km/h),   these  
a

lerts   flash,   accompanied   by   an   audible   signal  
f

or   two   minutes.   After   this   period,   these   alerts  
r

emain   on   fixed,   while   the   front   seat   belts   are  
n

ot   fastened.
On   switching   on   the   ignition,   the   warning  
lam

p
 A
  remains   on,   as   well   as   the  
c

orresponding   points   in   the   indicator   B
, if the
driver   and/or   one   or   more   passengers   have   not  
f

astened   their   seat   belt.
At   speeds   above   12   mph   (20   km/h),   these  
a

lerts   flash,   accompanied   by   a   message   and  
a

n   audible   signal   for   two   minutes.   After   this  
p

eriod,   these   alerts   remain   on   fixed,   while   the  
s

eat   belts   are   not   fastened.
6
Safety

256
1. Sealing
Repair procedure
Avoid removing any foreign bodies which   have   penetrated   into   the   tyre.F

U
ncoil the white pipe G  
f
ully.
F  
U
nscrew   the   cap   from   the   white   pipe.
F
C
onnect the white pipe to the valve of the
tyre   to   be   repaired.
F
 
S

witch   off   the   ignition.
F

T

urn the selector A to the "sealant"
position.
F
 
C

heck   that   the   switch   B is in
position "O" . F  
C
onnect   the   compressor's   electric   plug   to  
t

he   vehicle's   12   V   socket.
F  
S
tart   the   vehicle   and   leave   the   engine  
r

unning.
Take care, this product is harmful (
e.g.   ethylene-glycol,   colophony...)   if s

wallowed   and   causes   irritation   to   the   eyes.
Keep this product out of the reach of children. Do
  not   start   the   compressor   before  
c

onnecting   the   white   pipe   to   the   tyre  v
alve:   the   sealant   product   would   be  e
xpelled   through   the   pipe.
Practical information

260
Checking tyre pressures /
inflating accessories
You can also use the compressor, without injecting   any   product,   to:
-
 
c
heck   or   adjust   the   pressure   of   your   tyres,
-
 
i
nflate   other   accessories   (balls,  
b

icycle tyres...).
F

T
urn the selector A to the "
ai
r"
position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.
F
 
C
onnect   the   black   pipe   to   the  
v

alve   of   the   wheel   or   accessory.
 I

f   necessary,   fit   one   of   the   adaptors  
s

upplied   with   the   kit   first. F
 C onnect   the   compressor's   electrical  
c

onnector   to   the   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   and   let   the   engine   run.
F
 
A
djust   the   pressure   using   the   compressor  
(

to   inflate:   switch   B in position "I";
 
t

o deflate:   switch   B in position "O"
 
and  
p

ress button C),
  according   to   the   vehicle's  
t

yre   pressure   label   or   the   accessory's  
p

ressure   label.
F
 
R
emove   the   kit   then   stow   it.Should
  the   pressure   of   one   or   more  
t

yres   be   adjusted,   it   is   necessary   to  
r

einitialise   the   under-inflation   detection  
s

ystem.
Refer
  to   the   "Under-inflation   detection"  
s

ection.
Practical information

286
Engine compartment fuses
An additional fusebox is fitted in front of the battery,   for   type   2.
The
 
fusebox
 
is
 
placed
 
in
 
the
 
engine
 c
ompartment
 
near
 
the
 
battery
 
(left-hand
 
side).Access to the fuses
F Unclip   the   cover,   by   pushing   the   two   red  l
atches   towards   the   rear   of   the   vehicle.
F
 
C
hange   the   fuse   (see   corresponding  
par

agraph).
F
 
W
hen   you   have   finished,   close   the   cover  
c

arefully   to   ensure   correct   sealing   of   the  
f

usebox.
Practical information

288
12 V battery
The battery is located under the bonnet.
F or   access   to   the   (+)   terminal:
F
 
r
elease   the   bonnet   using   the   interior   lever,  
t

hen   the   exterior   safety   catch,
F
 
r
aise   the   bonnet   and   secure   it   with   its   stay,
F

l
ift the plastic cover for access to
the
  (+)   terminal.
Access to the battery
Procedure for starting the engine using another battery or charging a discharged battery.
T he presence of this label, in particular
with
  the   Stop   &   Start   system,   indicates  
t

he   use   of   a   12   V   lead-acid   battery   with  
s

pecial
 t
echnology
 a
nd
 s
pecification;
 t

he   involvement   of   a   CITROËN   dealer  
o

r   a   qualified   workshop   is   essential  
w

hen   replacing   or   disconnecting   the  
b

attery.
After
  refitting   the   battery,   the   Stop   &
 S

tart   system   will   only   be   active   after   a
 c

ontinuous   period   of   immobilisation   of   the
 v

ehicle,   a   period   which   depends   on   the
 c

limatic   conditions   and   the   state   of   charge
 o

f   the   battery   (up   to   about   8   hours). When
  your   vehicle's   battery   is   discharged,   the  
e

ngine   can   be   started   using   a   slave   battery  
(

external   or   on   another   vehicle)   and   jump   lead  
c

ables.
Starting using another
battery
First check that the slave battery has a nominal   voltage   of   12   V   and   a   capacity  
a

t   least   equal   to   that   of   the   discharged  
b

attery.
Do
  not   try   to   start   the   engine   by  
c

onnecting   a   battery   charger.
Do
  not   disconnect   the   (+)   terminal   when  
t

he   engine   is   running.
Practical information

289
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before   disconnecting   the   battery.
Close
  the   windows   and   the   doors   before  
d

isconnecting   the   battery.
Following reconnection
of the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 
t
he   electric   blind(s),
-
 ...
F

 
R

emove
 
the
 
plastic
 
cover
 
from
 

the
 
(+)
 
terminal,
 
if
 
your
 
vehicle
 
has
 
one.
F
 
C

onnect
 
the
 
red
 
cable
 
to
 
the
 
positive
 
t

erminal
 
(+)
 
of
 
the
 
flat
 
battery
 
A
, then to the
positive
 
terminal
 
(+)
 
of
 
the
 
slave
 
battery
 
B.
F
 
C

onnect
 
one
 
end
 
of
 
the
 
green
 
or
 
black
 
c

able
 
to
 
the
 
negative
 
terminal
 
(-)
 
of
 
the
 
s

lave battery B (or earth point on the other
vehicle).
F
 
C

onnect
 
t

he
 
o

ther
 
e

nd
 
o

f
 
t

he
 
g

reen
 
o

r
 
b

lack
 c
able to the earth point C
 
on
 
the
 
broken
 d
own
 
vehicle
 
(or
 
on
 
the
 
engine
 
mounting).
F
 
S

tart
 
the
 
engine
 
of
 
the
 
vehicle
 
with
 
the
 
g

ood
 
battery
 
and
 
leave
 
it
 
running
 
for
 
a
 
few
 
m

inutes.
F
 
O

perate
 
the
 
starter
 
on
 
the
 
broken
 
down
 
v

ehicle
 
and
 
let
 
the
 
engine
 
run
 I

f
 
the
 
engine
 
does
 
not
 
start
 
straight
 
away,
 
s

witch
 
off
 
the
 
ignition
 
and
 
wait
 
a
 
few
 
m

oments
 
before
 
trying
 
again.
F
 
W

ait
 
until
 
the
 
engine
 
returns
 
to
 
idle
 
then
 
d

isconnect
 
the
 
jump
 
lead
 
cables
 
in
 
the
 
r

everse
 o

rder.
F
 
R

efit
 
the
 
plastic
 
cover
 
to
 
the
 
(+)
 
terminal,
 
if
 
y

our
 
vehicle
 
has
 
one.
Some
 
functions
 
are
 
not
 
available
 
if
 
the
 
b

attery
 
is
 
not
 
sufficiently
 
charged.
7
Practical information

290
The batteries contain harmful substances such   as   sulphuric   acid   and   lead.   They m

ust   be   disposed   of   in   accordance
 w

ith   regulations   and   must   not,   in   any
 c

ircumstances,   be   discarded   with   household
 w

aste.
Take
  used   remote   control   batteries   and
 v

ehicle   batteries   to   a   special   collection   point.
Protect your eyes and face before handling   the   battery.
All
  operations   on   the   battery   must   be  
c

arried   out   in   a   well   ventilated   area   and  
a

way   from   naked   flames   and   sources  
o

f   sparks,   so   as   to   avoid   the   risk   of  
e

xplosion   or   fire.
Do
  not   try   to   charge   a   frozen   battery;  
t

he   battery   must   first   be   thawed   out   to  
a

void   the   risk   of   explosion.   If   the   battery  
h

as   been   frozen,   before   charging   have  
i

t   checked   by   a   CITROËN   dealer   or   a  
q

ualified   workshop   who   will   check   that  
t

he   internal   components   have   not   been  
d

amaged   and   the   casing   is   not   cracked,  
w

hich   could   cause   a   leak   of   toxic   and  
c

orrosive   acid.
Do
  not   reverse   the   polarity   and   use   only  
a

  12   V   charger.
Do
  not   disconnect   the   terminals   while  
t

he   engine   is   running.
Do
  not   charge   the   batteries   without  
d

isconnecting   the   terminals   first.
Wash
  your   hands   after wards.
It
 
is
 
advisable
 
to
 
disconnect
 
the
 
battery
 
i

f
 
the
 
vehicle
 
is
 
to
 
be
 
left
 
unused
 
for
 
m

ore
 
than
 
one
 
month.
do n
ot push the vehicle to start the
engine
  if   you   have   an   electronic   or  
a

utomatic   gearbox.Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F  F ollow   the   instructions   for   use   provided   by  
t

he   manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered   with   sulphate  
(

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
With
  Stop   &   Start,   the   battery   does   not  
h

ave   to   be   disconnected   for   charging.
Do
 
not
 
apply
 
excessive
 
force
 
on
 
the
 
t

ab
 
as
 
locking
 
will
 
not
 
be
 
possible
 
if
 
the
 
c

lamp
 
is
 
not
 
positioned
 
correctly;
 
start
 
t

he
 
procedure
 
again.
Disconnecting the (+) cable
F Raise   the   locking   tab   D fully to release the
cable t erminal c lamp E.
Reconnecting the (+) cable
F Position   the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
Practical information