ECO mode Citroen C5 2000 (DC/DE) / 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 19
GENERAL
LUBRICANTS – TOTAL recommended oils
S.A.E. Norm - Table for selection of engine oil grade Factory evolutions in 2000 model year
CITROËN engines are lubricated at the factory with TOTALoil of grade
S.A.E.5W-30.
TOTALoil of grade S.A.E.5W-30allows improved fuel economies
(approx. 2.5%).
This oil is not used in the following engines :
- XU10 4 RS – XSARA VTS 2.0i 16V(3-door)
- SOFIM – RELAY 2.8 Dand 2.8 TD.
Engine oil norms
These engine oils have been classified by the following recognised
organisations:
SAE :Society of Automotive Engineers.
API : American Petroleum Institute.
ACEA : Association des Constructeurs Européens d'Automobiles.
E4AP006D

Downloaded from www.Manualslib.com manuals search engine 21
GENERAL
LUBRICANTS – TOTAL recommended oils
Recommendations.
Denominations of TOTALoils, according to country of marketing :
TOTAL ACTIVA(France only).
TOTAL QUARTZ(Outside France).
These oils must comply with the following norms :
Petrol and dual fuel petrol / LPG engines: ACEA A3-98 and API SJ.
Diesel engines: ACEA B3-98and API CF.
Summary
Engine oil norms to be respected in 2001 model year.
(*) =It is essential not to use engine oils respecting these norms for the following engine-types :
XU10J4RS, 1580 SPI, SOFIM 2.8 D and SOFIM 2.8 TD.
IMPERATIVE : From 1999 model year, to preserve engine performance, all engines fitted in CITROEN vehicles must
be lubricated with high quality oils (synthetic or semi-synthetic)
WARNING : Engines fitted in CITROEN vehicles prior to 2000 model year must not be lubricated with oil complying
with standards ACEA A1-98 / B1-98 and API SJ/CF EC.
Model year Types of engine ACEA norms API norms
Petrol and dual fuel petrol /
A3-98 or A1-98 (*) SJ or SJ / EC (*)
2001 model yearLPG engines
Diesel enginesB3-98 or B1-98 (*) CF or CF / EC (*)

Downloaded from www.Manualslib.com manuals search engine 197
RECOMMENDATIONS - PRECAUTIONS (AL 4 AUTOMATIC GEARBOX)
Engines : 6FZ - RFN - RHZ
Procedure to be followed prior to carrying out repairs on AL4 autoactive gearbox
CLUTCH
GEARBOX
DRIVESHAFTS
If a gearbox malfunction occurs, there are two possible configurations
depending on the seriousness of the fault :
- Gearbox in back-up mode with a replacement programme of
(the fault values are taken in substitution).
- Gearbox in back-up mode with an emergency programme
(3rd hydraulic).
WARNING : In the emergency programme, an impact is felt when
changing P/R, N/RandN/D.
Réception client.
Discuss with the customer, to find out all the malfunction symptoms..
Oil quality – Oil level.
If the gearbox has suffered a serious fault resulting in a malfunction or
the destruction of a clutch, the oil will overheat and become
contaminated with impurities : the oil is said to be «burnt».
This is characterised by a black colour and the presence of an
unpleasant smell.
ESSENTIAL : The gearbox must be replaced.Oil quality.
See corresponding operation.
An excessive oil level can result in the following consequences :
- Excessive heating of the oil.
- Oil leaks.
An insufficent level causes the destruction of the gearbox.
Top up the level of oil in the gearbox (if necessary).
Check using a diagnostic tool.
Read the fault codes (engine and gearbox).
Absence de codes défauts.
Carry out parameter measures, actuator tests and a road test.
Presence of fault codes.
Carry out the necessary repairs.
Delete the fault codes.
Carry out a road test to check the repair and, if need be, modify the
gearbox ECU parameters (this is essential after an initialisation of the ECU).

Downloaded from www.Manualslib.com manuals search engine 198
CLUTCH
GEARBOX
DRIVESHAFTS
RECOMMENDATIONS - PRECAUTIONS (AL 4 and 4 HP 20 AUTOMATIC GEARBOXES)
Engines : 6FZ - RFN - RHZ - XFX - 4HX
Procedure prior to carrying out repairs (continued)
When the ECU detects an erroneous or non-existent value
on input or output :
- It writes the fault in memory.
- For each associated context, it writes the context of the oldest fault
in memory.
- It initiates a back-up mode strategy.
There are two types of back-up modes :
- The ECU makes replacement values available (relating to comfort,
gear selection quality, loss of functions).
- Access to emergency programme (only 3rd ratio and reverse are
available)
NOTE : 4 HP 20 : A snatching may be felt when changing :P/R - N/R - N/D.Reading the fault codes.
Read the fault codes.
No fault codes present :
Carry out a measure of parameters.
Anomalies present :
- YES : Carry out the necessary repairs.
- NO : Read the fault codes – engine ECU.
- Carry out a road test.
Following an initialisation of the ECU, for a certain period of time there
may be an inconsistent gear selection quality(while ECU parameters
are adapted to the gearbox).
To achieve a consistent standard, it is necessary to carry out a road test
taking in frequent gear changes (auto-adaptive laws).

Downloaded from www.Manualslib.com manuals search engine 203
CLUTCH
GEARBOX
DRIVESHAFTS
4 HP 20 GEARBOX CONTROLS
Engines : XFX - 4HX
Selection control (continued).
In positionM, selection is by an electronic sensor located close to the gear lever.
The variation of flux necessary to the movement of the sensor cells is obtained by a magnet located on
the lever itself. This enables the change of status. The information is transmitted to the gearbox ECU.
Two switches placed on the gear control gate permit the driver to choose one of the following three
driving programmes:
- Normal :The normal programme operates in the absence of the other two (Eco law, autoadaptative mode).
- Sport :Permits a more dynamic, sporty performance.
- Snow :Facilitates starting and adhesion on slippery surfaces.
To return to the normal programme, press a second time on the sport switch or snow switch.
Only when the selector is in position(P)or (N)can the engine be started.
(1)Control linkage with ball-joint.
(2)Automatic adjustment(Push-button pressed in to lock the control adjustment, springs out for the
adjustment to be made) «c» Push-button locking clip in pressed-in position.
(3) Cable sleeve stop.
The automatic gearbox is controlled by cable.
B3CP3DLC