check engine Citroen C5 2000 (DC/DE) / 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine PRESENTATION
THIS HANDBOOK summarises the specifications, adjustments, checks and special features of theCITROEN C5.
The handbook is divided into the following sections representing the main functions :
GENERAL - ENGINE - INJECTION - IGNITION - CLUTCH - GEARBOX - DRIVESHAFTS - AXLES - SUSPENSION - STEERING - BRAKES - HYDRAULICS -
ELECTRICAL - AIR CONDITIONING.

Downloaded from www.Manualslib.com manuals search engine INJECTION
Idling - antipollution 111
Petrol injection 112
Emission standards 113 - 119
Prohibited operations : HDi 120 - 121
Safety requirements : HDi 122 - 123
Checking the fuel supply circuit 124 - 125
Checking the air supply circuit 126 - 130
Exhaust gas recycling 131 - 134
Checking turbo pressure 135 - 138
Features of injection systems 139 - 168
IGNITION
Sparking plugs 169
CLUTCH-GEARBOX
Speedometers 170
Clutch specifications 171 - 172
Gearbox and tyre specifications 173 - 174
BE4/5 gearbox controls 175 - 183
ML/5 gearbox controls 184 - 192
AL4-4HP20 gearbox controls 193 - 203
Driveshafts 204
AXLES-SUSPENSION
Wheels and tyres 205 - 211
Axle geometry 212 - 214
Front and rear axle 215 - 216Suspension 217 - 220
Steering specifications 221 - 222
BRAKES
Brake specifications 223 - 228
Handbrake adjustment 229
Bleeding and filling braking system 230 - 233
HYDRAULICS
Specifications 234 - 237
Suspension spheres 238 - 240
ELECTRICAL
Starter motors 241
Alternators 242
Charging circuit 243
AIR CONDITIONING
Quantities in R 134a aircon system 244
Special features 245
Pollen filter 246
Dryer cartridge 247 - 249
Checking oil level 250 - 251
Checking pressures 252
Air conditioning : 6FN-RFN-RLZ 253
Air conditioning circuit : XFX 254
Air conditioning circuit : RHY-RHZ 255
Air conditioning circuit : 4HX 256
INDEX
GENERAL
Identification of vehicles 1 - 4
General : Dimensions 5 - 6
Weight specifications 7 - 8
Towing specifications 9 - 10
Lifting / supporting the vehicle 11 - 14
Capacities 15 - 18
Lubricants 19 - 32
ENGINES
Engine specifications 34 - 58
Cylinder head marking / tightening
6FZ-RFN-RLZ 38
XFX 51 - 52
RHY-RLZ 55 - 56
4HX 57 - 58
Auxiliaries drive belt 59 - 68
Checking and setting valve timing 69 - 90
Power unit suspension 91 - 95
Exhaust system 96 - 100
Cooling system 101 - 107
Checking oil pressures 108
Oil filter 109
Filling and bleeding engine coolant 110

Downloaded from www.Manualslib.com manuals search engine GENERAL
15
CAPACITIES (in litres)
Draining method.
Oil capacities are defined as below.
1/ Vehicle on horizontal ground (in the high position, if hydropneumatic suspension).
2/Engine warm (oil temperature 80°C).
3/Drain oil sump + remove filter cartidge (time for draining to last drops = 15 minutes).
4/ Refit drain plug + filter cartridge.
5/ Refill the engine.
6/ Start the engine (to allow the cartridge to fill).
7/Stop the engine(to allow oil to stabilise for 5 minutes).
ESSENTIAL : Systematically check the oil level using the oil dipstick.

Downloaded from www.Manualslib.com manuals search engine GENERAL
Engine type
Engine with filter change
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
6FZ RFN RLZ RHY RHZ
4.25 4.75
1.7 1.5
1.8 1.8 1.8 1.8
6 6 8.3
3 3 5.3
4.3
8.8 – 9.3 (*) 8.8 10.7
66 68
16
CAPACITIES (in litres)
1.8i 16V 2.0i 16V 2.0 HPi 2.0 HDiPetrol
Diesel
Vehicle without air conditioning
(*) = With automatic gearbox
ESSENTIAL : Systematically check the oil level using the oil dipstick.
Auto.Auto.Auto.

Downloaded from www.Manualslib.com manuals search engine GENERAL
17
Engine type
Engine with filter change
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
CAPACITIES (in litres)
Petrol
Vehicle with air conditioning
(*) = With automatic gearbox.
ESSENTIAL : Systematically check the oil level using the oil dipstick.
1.8i 16V 2.0i 16V 3.0i V6
Auto.Auto.Auto.
6FZ RFN RLZ XFX
4.25 5.25
1.7 2
1.8 1.8 1.8
6 6 8.3
3 3 5.3
4.3
8.8 – 9.3 (*) 8.8 14
662.0 HPi

Downloaded from www.Manualslib.com manuals search engine 18
GENERAL
Engine type
Engine with filter change
EBetween Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
CAPACITIES (in litres)
Diesel
Vehicle with air conditioning
ESSENTIAL : Systematically check the oil level using the oil dipstick
RHY RHZ 4HX
4.5 4.75
1.7 1.5
1.8 1.8
6 8.3
3 5.3
4.3
10.7 - 11.7 - (With additional heating).
68 2.0 HDi 2.2 HDi
Auto.
Auto.

Downloaded from www.Manualslib.com manuals search engine ENGINE
47
Engine : XFX
SPECIAL FEATURES : TIGHTENING TORQUES ( m.daN)
(8) Crankshaft bearings
Carry out the following operations :
- Clean the threads of the screws with a brush.
- Refit the screws with a coating of grease, on threads and under
heads "MOLYKOTE G RAPID PLUS".
- Check that the 8 centring pins are in place.
Tightening :
- Pre-tighteningM11to 3 ± 0.3 (Order from 1to8)
- Pre-tighteningM8to 1 ± 0.1(Orer fromAto H)
- TighteningM6 to 1 ± 0.1(Order from a to m)
- UntighteningM11to M8
Proceed screw by screw :
- TighteningM11to 3 ± 0.3(order from 1to 8), then
One angular tightening of 180°
- TighteningM8 to 1 ± 0,1(Order from Ato H), then
One angular tightening of180°
Max. length under heads of the screws M11 = 131.5 mm.
Max. length under heads of the screws M8 = 119 mm.
B1BP1GYD

Downloaded from www.Manualslib.com manuals search engine ENGINE
60
AUXILIARY EQUIPMENT DRIVE BELT
Engines : all types Petrol and Diesel
TOOLS
Belt tension measuring instrument : 4122 - T
(C.TRONIC 105.5)
WARNING : If using tool 4099-T (C.TRONIC 105), refer to the correspondence table on page 59.
ESSENTIAL:
Before refitting the auxiliary equipment drive belt, check that:
1 / The roller(s) rotate freely(no play or stiffness).
2 /The belt is correctly engaged in the grooves of the various pulleys.

Downloaded from www.Manualslib.com manuals search engine ENGINE
62
AUXILIARY EQUIPMENT DRIVE BELT
Engine : XFX
Tools
[1] Ratchet S.171 FACOM (1/2 square) S 171.
[2] Reduction box S.230 FACOM (1/2-3/8) S 230.
Remove.
Remove the engine cover.
Pivot the tensioner roller bracket (1) clockwise, until it locks, using tools[1]
and [2]at «a».
Remove the auxiliary equipment drive belt.
ESSENTIAL : Check that the guide rollers are turning freely.
(No play and no tightness).
Refit.
Refit the auxiliary equipment drive belt:
Respect the following order of assembly:
- The crankshaft pulley (2).
- The tensioner roller (3).
Release the tensioner roller bracket (1), by turning it anti-clockwise, using
tools [1] and [2].
ESSENTIAL : Make sure that the belt is correctly positioned in the
grooves of the various pulleys.
B1BP27ECB1BP27FC

Downloaded from www.Manualslib.com manuals search engine ENGINE
64
AUXILIARY EQUIPMENT DRIVE BELT
Engines : RHY - RHZ
Without air conditioning (continued)
Refit.
Re-used belt.
- Compress the tensioner roller(2)by action at «a»(anti-clockwise), tool [4].
- Refit the belt.
WARNING : Respect the direction in which the belt is fitted.
- Remove the tool [4].
New belt.
- Refit the belt.
- Turn the eccentric roller (3), tool[1] (clockwise)to free the tool [2]from its pegging at «b».
- Hold the eccentric roller (3), tool [1], and tighten the screw(1) to 4.3 ± 0.4 m.daN.
- Remove the tool [2].
- Rotate the crankshaft 4 times in the direction of rotation.
- Check that it is possible to peg at «b», tool [3].
- If not possible to peg, restart the adjustment.
B1BP1YMD