engine Citroen C5 2008.5 (RD/TD) / 2.G Manual PDF
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5, Model: Citroen C5 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.9 MB
Page 166 of 306
166
P R A C T I C A L I N F O R M A T I O N
Removing a wheel
P a r k t h e v e h i c l e o n s t a b l e , fi r m
ground that is not slippery. apply
the parking brake.
If your vehicle is equipped with
"Hydractive III+" suspension,
with the engine running at idle,
adjust the ground clearance to
i t s m a x i m u m h e i g h t .
Switch off the ignition and en-
g a g e fi r s t g e a r o r r e v e r s e g e a r
depending on any slope (for a
v e h i c l e w i t h a u t o m a t i c g e a r b o x ,
select position P).
I f y o u r v e h i c l e i s fi t t e d w i t h
"Hydractive III+" suspension,
position the chock, whichever di-
rection the gradient may be in, in
front of the front wheel diametri-
cally opposite to the one to be
replaced.
Position the jack at one of the
four jacking-points provided
on the underbody close to the
wheels, then use the wheelbrace
to unwind the jack until it reaches
the ground.
Remove the protector from each
bolt using tool 3 .
Slacken the wheel bolts.
Before positioning the
jack:
Always adjust the vehicle’s
g r o u n d c l e a r a n c e t o t h e " m a x i -
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehi-
cle (do not use the hydraulic
adjustments),
Immobilise your vehicle on hori-
zontal, stable and non-slippery
ground,
Ensure that any passengers
have left the vehicle and are in
a safe place .
Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
s p e c i fi c t o y o u r v e h i c l e . D o n o t u s e
them for any other applications.
Have the original wheel repaired
a n d r e fi t t e d a s s o o n a s p o s s i b l e .
C o n t i n u e t o e x t e n d t h e j a c k u n t i l
the wheel is a few centimetres
off the ground.
Undo the bolts, remove the
wheel.
Page 183 of 306
180
11
P R A C T I C A L I N F O R M A T I O N
FUSEBOX C
Fuse N° Rating
Function
F1 15 A Rear screen wipe (Tourer)
F2 30 A Locking and deadlocking relay
F3 5 A Airbags
F4 10 A A u t o m a t i c g e a r b o x - a d d i t i o n a l h e a t e r u n i t ( D i e s e l ) - e l e c t r o c h r o m e r e a r v i e w m i r r o r s
F5 30 A Front window - sun roof - passenger door lighting - passeng er rear view mirror adjustment
F6 30 A Rear window
F7 5 A V a n i t y m i r r o r l i g h t i n g - G l o v e b o x l i g h t i n g - i n t e r i o r l a m p s - t o r c h ( t o u r e r )
F8 20 A R a d i o - C D c h a n g e r - C o n t r o l s a t t h e s t e e r i n g w h e e l - D i s p l a
y - D e fl a t i o n d e t e c t i o n - E l e c t r i c
boot ECU
F9 30 A Cigar-lighter - front 12 V socket
F10 15 A Alarm - Controls on the steering wheel, signalling and scre en wipe controls
F11 15 A Low current ignition switch
F12 15 A Driver’s electric seat - instrument panel - seat belt not fasten
ed warning lamps -air
conditioning controls
F13 5 A Engine relay unit - Hydraulic suspension pump cut-off relay - a irbag ECU supply
F14 15 A Rain and brightness sensor - parking assistance - passenger’s electri
c seat - trailer relay
u n i t - H I F I a m p l i fi e r E C U - H a n d s - f r e e k i t - L a n e D e p a r t u r e W a r n i n g S y s t e m
F15 30 A Locking and deadlocking relay
F17 40 A H e a t e d r e a r s c r e e n - e x t e r i o r h e a t e d r e a r v i e w m i r r o r s
FSH SHUNT PARK SHUNT
Page 184 of 306
181
11
P R A C T I C A L I N F O R M A T I O N
Fuses under the bonnet
After a repair,
c a r e f u l l y r e fi t
the
cover.
Any repairs on the MAXI fuses
(that give additional protection),
located in the fuseboxes, must
be left to a CITROËN dealer.
Access to the fuses
Undo each screw by a 1/4 turn. Table of fuses
Fuse N° Rating Function
F1 20 A Engine control unit
F2 15 A Horn
F3 10 A Screen wash pump
F4 10 A Headlamp wash pump
F5 15 A Starter
F6 10 A A i r fl o w m e t e r - D i r e c t i o n a l h e a d l a m p s -
Diagnostic socket
F7 10 A Automatic selector lever lock - Power steering
F8 25 A Starter
F9 10 A Clutch switch - STOP switch
F10 30 A Starter
F11 40 A Air conditioning blower
F12 30 A Wipers
F13 40 A BSI supply (ignition on)
F14 30 A -
F15 10 A Right-hand main beam
F16 10 A Left-hand main beam
F17 15 A Right-hand dipped beam
F18 15 A Left-hand dipped beam
F19 15 A Starter
F20 10 A Starter
F21 5 A Starter
Page 185 of 306
182
P R A C T I C A L I N F O R M A T I O N
Fuses on the battery
(All engines except V6 HDi)
Fuse N° Rating Function
F6 25 A R e a r 1 2 V s o c k e t ( m a x p o w e r : 1 0 0 W )
F7 15 A Foglamps
F8 20 A Additional burner (Diesel)
F9 30 A Electric parking brake
Access to the fuses
detach and remove the cover,
change the fuse. Table of fuses
Your vehicle’s electrical
system is designed to oper-
ate with either standard or
optional equipment.
Before installing electrical equip-
ment or accessories on your vehi-
cle, consult a CITROËN dealer.
CITROËN declines all responsibil-
ity for the consequences and costs
that are caused by faults or repairs
on your vehicle resulting from the in-
stallation of accessories that are not
supplied and/or not recommended
by CITROËN and not installed in
conformity with its requirements,
particularly when the total consump-
t i o n o f a d d i t i o n a l d e v i c e s e x c e e d s
10 milliamperes.
T h e M a x i f u s e s g i v e a d d i t i o n a l p r o -
tection to electrical systems. any
work on them must be carried out
by a CITROËN dealer.
After a repair,
c a r e f u l l y r e fi t
the
cover.
If the cover is not correctly po-
sitioned or not properly closed,
this could cause serious prob-
lems on your vehicle. For the
same reason, take care not to
spill any liquid in the fusebox.
Page 186 of 306
183
11
P R A C T I C A L I N F O R M A T I O N
BATTERY
Procedure for charging your battery
w h e n i t i s fl a t o r f o r s t a r t i n g t h e e n -
gine using another battery. Starting using another
battery
Access to the battery V6 HDi engine
The battery is located under the
bonnet.
To gain access to it:
open the bonnet using the inte-
r i o r l e v e r , t h e n t h e e x t e r i o r l e v e r ,
secure the bonnet strut,
remove the plastic cover to gain
access to the two terminals,
u n c l i p t h e f u s e b o x t o r e m o v e
the battery, if necessary. The battery is located in the boot un-
der the left-hand wing trim.
To gain access to it:
open the boot,
o p e n t h e fl a p a n d r e m o v e t h e
battery.
Lift the pins to remove the front
left headlamp cover (V6 HDi en-
gine).
Connect the red cable to the
p o s i t i v e t e r m i n a l ( + ) o f t h e fl a t
battery A , then to the positive ter-
minal (+) of the slave battery B .
Connect one end of the green or
black cable to the negative ter-
minal (-) of the slave battery B .
V6 HDi engine: the positive ter-minal (-) is located under the red cover.
Connect the other end of the
green or black cable to the earth
point C on the broken down ve-
hicle.
Operate the starter, let the en-
gine run.
Wait until the engine returns to
idle and disconnect the cables.
Page 187 of 306
184
P R A C T I C A L I N F O R M A T I O N
Charging the battery using a
battery charger
Disconnect the battery from the
vehicle.
Follow the instructions for use
provided by the manufacturer of
the charger.
Reconnect starting with the neg-
ative terminal (-).
Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.
The batteries contain harm-
ful substances such as sul-
phuric acid and lead. They
must be disposed of in accordance
with regulations and must not, in
any circumstances, be discarded
with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Do not disconnect the ter-
minals while the engine is
running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not touch the clips during the
operation.
Do not lean over the batteries.
Disconnect the cables in the re-
verse order to connection, ensur-
ing that they do not touch.
Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery. Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
tems. However, if slight malfunctions
remain following this operation, con-
tact a CITROËN dealer.
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the glass panoramic roof blind,
- the GPS satellite navigation
system.
Page 188 of 306
185
11
P R A C T I C A L I N F O R M A T I O N
ENERGY ECONOMY MODE
System which manages the duration
of use of certain functions to con-
s e r v e a s u f fi c i e n t l e v e l o f c h a r g e i n
the battery.
After the engine has stopped, you can
still use functions such as the audio
and telematics system, windscreen
wipers, dipped headlamps, courtesy
l i g h t s , e t c . f o r a m a x i m u m c o m b i n e d
duration of thirty minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-func-
tion screen indicating that the vehi-
cle has switched to economy mode
and the active functions are put on
standby.
If the telephone is being used at this
time:
- it will be maintained for 5 minutes with radio-CD hands-free kit,
-
it will be interrupted after 10 minutes with the MyWay audio-navigation
system,
- you can complete your call with the NaviDrive system.
T h i s p e r i o d m a y b e s i g n i fi c a n t l y r e -
duced if the battery charge is low. Exiting economy mode
These functions are reactivated
a u t o m a t i c a l l y n e x t t i m e t h e v e h i c l e
is driven.
In order to resume the use of
these functions immediately,
start the engine and let it run for
a few minutes.
The time available will then be dou-
ble the duration for which the engine
was left running. However, this time
w i l l a l w a y s b e b e t w e e n fi v e a n d t h i r t y
minutes.
A fl a t b a t t e r y p r e v e n t s t h e
engine from starting (refer
to the corresponding para-
graph).
Page 189 of 306
186
P R A C T I C A L I N F O R M A T I O N
TOWING THE VEHICLE
Procedure for having your vehicle
towed or for towing another vehicle
using a removable towing eye.
Access to the tools
The towing eye is installed in the
j a c k b o x p l a c e d i n t h e s p a r e w h e e l .
To gain access to it:
open the boot,
r a i s e t h e fl o o r ,
remove the towing eye from the
j a c k b o x . Towing your vehicle
On the front bumper, unclip the
cover by pressing at the top.
Screw the towing eye in fully.
Attach the towing bar.
Switch on the hazard warning
lamps on the towed vehicle.
Place the gear lever in neutral
(position N on the automatic
g e a r b o x ) . Towing another vehicle
On the rear bumper, unclip the
cover by pressing:
- on the right (Saloon),
- at the bottom (Tourer).
Screw the towing eye in fully.
Attach the towing bar.
Switch on the hazard warning
lamps on the towed vehicle.
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
t h e n e x t t i m e t h e e n g i n e i s s t a r t e d . When towing with all four wheels
on the ground, always use a towing
bar.
When towing with only two wheels
on the ground, always use profes-
sional lifting equipment.
When towing with the engine off,
there is no longer any braking or
steering assistance.
Page 190 of 306
187
11
P R A C T I C A L I N F O R M A T I O N
TOWING A TRAILER, A CARAVAN, ETC.
Towbar suited to the attachment of a
trailer or caravan with additional sig-
nalling and lighting.
Your vehicle is primarily designed
for transporting people and luggage,
but it may also be used for towing a
trailer.
We recommend the use of genuine
CITROËN towbars and their har-
nesses that have been tested and
approved from the design stage
o f y o u r v e h i c l e , a n d t h a t t h e fi t -
ting of the towbar is entrusted to a
CITROËN dealer. I f t h e t r a i l e r i s n o t fi t t e d b y
a CITROËN dealer, it is
i m p e r a t i v e t h a t i t i s fi t t e d
using the electrical pre-equipment
installed at the rear of the vehicle,
in accordance with the manufactur-
er’s instructions.
Driving with a trailer subjects the
t o w i n g v e h i c l e t o m o r e s i g n i fi c a n t
stress and its driver must be par-
ticularly careful.
Driving advice
Distribution of loads
Distribute the load in the trailer
so that the heaviest items are as
c l o s e a s p o s s i b l e t o t h e a x l e a n d
the nose weight approaches the
m a x i m u m p e r m i t t e d w i t h o u t e x -
ceeding it.
Air density decreases with altitude,
thus reducing engine performance.
A b o v e 1 0 0 0 m e t r e s , t h e m a x i m u m
t o w i n g l o a d m u s t b e r e d u c e d b y 1 0 %
and so on for every 1 000 metres of
altitude.
Refer to the "Technical Data" section
for details of the weights and towing
loads which apply to your vehicle.
Side wind
Take into account the increased
sensitivity to side wind. Cooling
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled,
its cooling capacity is not dependent
on the engine speed.
To lower the engine speed, reduce
your speed.
T h e m a x i m u m t o w i n g l o a d o n a l o n g
slope depends on the gradient and
the ambient temperature.
In all cases, pay attention to the
coolant temperature.
If the warning lamp and
the STOP warning lamp
come on, stop the vehicle
and switch off the engine
as soon as possible.
Braking
Towing a trailer increases the brak-
ing distance.
Tyres
Check the tyre pressures of the
towing vehicle and of the trailer,
observing the recommended
pressures.
Lighting
Check the electrical signalling on
the trailer.
The rear parking assistance will
be deactivated automatically if an
original CITROËN towbar is used.
Page 192 of 306
189
11
P R A C T I C A L I N F O R M A T I O N
VERY COLD PROTECTION *
Moveable device which prevents the
intake of snow particles, which could
o b s t r u c t t h e a i r fi l t e r .
Diesel engine HDi 173 FAP
Normal position
T h e fl a p 2 is in a horizontal position
in the air duct 3 . Snow position
Push and rotate the knob 1 by
90° in the direction of the arrow
i n o r d e r t o p o s i t i o n t h e fl a p 2 in a
vertical position in the air duct 3 .
To return to the normal position,
push the knob 1 then rotate in the
opposite direction.
It is essential to remove the very cold
protection:
- W h e n t h e o u t s i d e t e m p e r a t u r e e x - ceeds 10 °C.
- When driving at speeds of over 7 5 m p h ( a p p r o x i m a t e l y 1 2 0 k m / h ) .
Diesel engine V6 HDi 208
FAP
Snow position
S l i d e t h e d e fl e c t o r 1 into the air
duct 2 and clip in.
* According to country.