lock Citroen C5 2008 (RD/TD) / 2.G User Guide

58
II
1
2
R E A R V I E W M I R R O R S
Fold-back of door mirrors
When the vehicle is parked, the door mirrors can be folded back either manually or electrically.
Electric fold-back
From the central position, one press towards the rear on control 1folds the rear view mirrors back.
To return them to the initial position, press again on control 1 towards the rear.
Automatic fold-back on locking
Automatic fold-back operates when you lock the doors.
The opposite movement will take place on unlocking, unless fold-back has been requested using control 1 before switching off the ignition.
Note: Automatic fold-back of the rear view mirrors can be deac-tivated. Contact a CITROËN dealer.
In reverse gear: adjustment of the indexed positions for the passenger’s and driver’s rear view mirrors
With the engine running:
1. Select the (driver's or passen-ger's) rear view mirror using control 1.
2. Engage reverse gear, the mirror glass automatically positions itself to improve your vision of the pavement.
3. Adjust the mirror to your prefer-ence using control 2.
These adjustments are automati-cally memorised.
The rear view mirrors resume their original position:
20 seconds after reverse gear is disengaged.
Once the vehicle reaches a speed of over 10 km/h (6 mph).
Deactivation of the driver's and passenger's indexed rear view mirrors function
To deactivate the function, move control 1 to the central position.
Note: this action cancels the indexing of the rear view mirrors if in progress.

92
III
A
Locking/unlocking from the inside
With the doors and the boot closed, pressing button A allows you to control the electric central locking and unlocking.
It is still possible to open the doors from the inside.
If one of the doors is open or not properly closed, central locking will not work.
A C C E S S
Anti-theft protection
On starting the vehicle, the system automatically locks the doors as soon as you reach approximately 10 km/h.
Note: If a door is opened, this will automatically lock itself again when the vehicle reaches approximately 10 km/h (6 mph).
Activation/Deactivation of the anti-intrusion protection
After switching on the ignition, make a long press on the central unlocking control until a message is displayed and a beep is heard.
Selection of doors / boot
After having selected “Plip action / Driver” in the “Vehicle parameters / Comfort” menu of the instrument panel screen.
Pressing the remote control unlocks the passenger door.
A 2nd successive press unlocks all of the doors and the boot.
If you decide to drive with the doors locked, remember that in the event of an accident this renders access more diffi -cult for the emergency services.
The warning lamp associated with the control A signals 3 statuses:lt fl ashes when the ignition key is in the stop position or when the key is not detected and the doors are locked.
It lights up when the vehi-cle is locked with the ignition switched on.It goes out when the doors are not locked.
Note: Control A is inactive if the vehicle has been locked using the remote control or the key.

93
III
BCD
A C C E S S
Manual operation (Emergency mode)
Driver's door
Insert the key into the lock to lock/unlock the door.
Passenger doors
It is possible to lock the passenger doors in the event of an electrical fault by using control B on each door:With the door open, unclip the plastic cover.
Insert an object, such as the end of a key, into the cavity and turn.
Replace the plastic cover.
Close the door.
After this operation, normal opera-tion resumes using the central unlocking control (inside the vehi-cle), the remote control or the key.

94
III
ABC
B
Manual closing
Lower the tailgate using the interior handle B.
Electric closing
Press the push-button C to close the tailgate.
Note : do not interrupt the closing of the tailgate ; if any obstacle pre-vents it closing, the operation will stop and the tailgate will automati-cally rise by a few centimetres.
TAILGATE (TOURER)
Manual opening
Press upwards on lever A and lift up the tailgate.
Electric opening
Press upwards on lever A, or press button B of the remote control.
Locking/unlocking
With the vehicle stationary, this is carried out using:
The remote control.
The key in a door lock.The interior central locking/unlocking control.


A C C E S S
In order to avoid risk of injury, make sure that no-one is in the vicin-ity of the boot when carrying out an electric opening manoeuvre.
Interrupting the opening/closing of the tailgate
When the tailgate is being closed electrically, you can interrupt its movement at any point by pressing the tailgate push-button C.
Note : After an interruption, the tailgate is held electrically in an intermediate position for about 10 minutes. After this period, the system automatically goes to standby and releases the tailgate.
To exit the intermediate position mode, close the tailgate electrically or manually.
Memorisation of an intermediate position
You can store an opening angle for the tailgate:Manually or automatically move the tailgate to the required posi-tion.
Make a long press on the push-button C. The system emits a beep.
Release the push-button C.
Cancelling the memorisation
With the tailgate in the intermedi-ate position, you can cancel the stored position :Make a long press on the push-button C. The system emits a beep.
Release the push-button C. The tailgate reverts to the fully open position.





The tailgate automatically locks when the vehicle is moving at a speed of over 10 km/h (6 mph), even if automatic central locking is deactivated. It is unlocked when a door is opened or when the central locking button is pressed (at a speed of less than 10 km/h (6 mph)).

104
III
3
2
6
7
2
3A7
Delayed start-up
Note : Before programming the delayed start-up of the heating, you must ensure that the clock is set to the correct time.
P R O G R A M M A B L E H E A T I N G
Programming the start-up time
Start-up may be programmed between 1 minute and 24 hours in advance.
You can store up to 3 different start-up times, but programme only 1 delayed start-up time.
Factory settings A :
Time 1 : 06:00.
Time 2 : 16:00.
Time 3 : 22:00.
Note : The factory settings are replaced once you adjust them. The programmed times are stored until they are re-programmed.



Press button 3 then buttons 2 or 7 in the next 10 seconds, until the desired start-up time is displayed.
Note : In the event of a battery failure, the factory settings are restored.
Note : if you wish to recall the other stored times, press several times on button 3 in the next 10 seconds until the desired programme number is displayed.
Cancelling the programmed time
To cancel the programmed start-up time, press briefl y on button 3.
Setting the time
Hold button 3 down and press but-ton 2 or button 7. Release button 3, the time is displayed and symbol 6fl ashes.
Use the two adjustment buttons 2(to go forward) or 7 (to go back) until the correct time is displayed.
Holding these buttons down will make the numbers displayed scroll more quickly.
Reading the time
Press button 2 or button 7 to dis-play the time.
When the heating mode is acti-vated, the remaining operating time is displayed in place of the time.

106
III
A
R E A R S E A T S
Rear head restraintsFlap for transport of long objects
A fl ap in the backrest, located to the rear of the armrest, facilitates the carrying of long objects.
Ensure that the objects are well secured and that they do not impede the operation of the gear lever.
For your safety, do not d r i v e w i t h t h e h e a d r e s t r a i n t s r e m o v e d ; these must be in place, correctly adjusted.
To lower them, press on the unlock-ing control A.
To remove them, pull upwards as far as possible and press on the unlocking control A.
The rear head restraints have two positions:A stowed position for when the seat is not occupied.
A deployed position for safety of passengers, locking into place including for a forward-facing child seat.

107
III
1
2
3
R E A R S E A T S
The red light on button 3 should no longer be visible - if not, push the seat all the way back.
Pull control 3 forwards to unlock the backrest 2.Move the backrest 2.
Pinch the seat cushion fi xings to remove them from their fasteners.
When repositioning:Fold the backrest 2 back up and lock it into place (the red light on button 3 should go out).Fold up the seat cushion 1.
Replace the head restraints if you had removed them.
Ensure that the front and rear back-rests are correctly locked in place.

114
III
2
2
1
221
1
I N T E R I O R L I G H T I N G
1. Interior lamps
Move control 1 to one of the 3 fol-lowing positions:
Automatic lighting of the interior lampsOn entering the vehicle:
They come on as soon as the vehicle is unlocked or a door is opened.
They go out 30 seconds after the doors are closed or when ignition is switched on.

122
III1AB
C
To install :
Position the left-hand end of the luggage-cover blind in its housing A behind the rear benchseat.A
Squeeze the blind’s control 1 and position it in place in its housing Bto the right-hand side.
Release the control to secure the luggage-cover blind.
Unroll it until it locks into place on the boot pillar.




L U G G A G E - C O V E R B L I N D ( T O U R E R )
To remove :
Press gently on the handle (PRESS). The luggage-cover blind rolls up automatically.
Squeeze control 1 and lift up the luggage-cover blind to the right then to the left to remove it.


To fold up :
Press gently on the handle (PRESS). The luggage-cover blind rolls up automatically.
The moveable section C can be folded up along the backrest of the rear benchseat.


123
III
33
44
1
1
22
The cargo net can be used behind the rear seats (row 2) when the luggage-cover blind is not fi tted, or behind the front seats (row 1).
Note : when using behind the front seats, the backrests and the seat cushions must be folded down (see section on rear seats).
CARGO NET (TOURER)
To install :
Fold down the backrests of the rear seats.
Position the cargo net roller over the two rails 1 located behind the rear seats (2/3 benchseat). The two notches 2 must be posi-tioned over the two rails.


Slide the 2 rails 1 into the notches 2 and push the roller (lengthwise) from right to left to lock it in.Put the backrests of the rear seats back into place.


To use in row 1 :
Fold down the backrests of the rear seats.
Open the cov-ers 3 of the corresponding high fi xing locations.


To use in row 2 :
Open the cov-ers 4 of the c o r r e s p o n d -ing high fi xing locations.
From the rear benchseat, unroll the cargo net by pushing it to disengage the retaining notches.
Position one of the ends of the cargo net’s metal bar in the corre-sponding fi xing location. Ensure that the notch is correctly lodged in the rail located inside the loca-tion 4.
Position the other notch in the 2nd fi xing location and pull the metal bar towards you.




Unroll the cargo net and posi-tion one of the ends of the net’s metal bars in the corresponding fi xing location. Ensure that the notch is correctly lodged in the rail located inside the location 3.
Pull on the cargo’s net’s metal bar to position the other notch in the 2nd fi xing location.