ECU Citroen C5 DAG 2008.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5 DAG, Model: Citroen C5 DAG 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.85 MB
Page 41 of 306

59 
3
C O M F O R T
  Storing driving positions  
 System which takes into account the  
settings of the driver's seat, exterior 
mirrors  and  air  conditioning.  It  ena-
bles you to store up to two positions 
using  the  buttons  on  the  side  of  the 
driver's seat.    Storing a position   
  Using buttons M/1/2  
   
     Switch on the ignition. 
  
     Adjust  your  seat  and  your  exte-
rior mirrors. 
  
     Press  button    M ,  then  press  but-
ton   1  or   2  within four seconds.   
  An  audible  signal  is  heard  indi- cating  that  the  storing  has  been  
taken into account.  
 Storing  a  new  position  cancels  the 
previous position.  
  Recalling a stored position   
  Ignition on or engine running  
   
        B r i e fl   y    p r e s s    b u t t o n      1   or    2   to  re-
call the corresponding position.  
 An audible signal is heard indicating  
the end of the adjustment.  
 When  the  ignition  is  on,  after  a  few  
consecutive  position  recalls,  the 
function will be deactivated until the 
engine  is  started,  to  prevent  dis-
charging of the battery.    For  your  safety,  avoid  storing  a 
driving position while driving.  
       REAR HEAD RESTRAINTS 
 The  rear  head  restraints  can  be  re- 
moved and have two positions;  
   -   high, position for use, 
  -   low, storage position.  
 To  raise  a  head  restraint,  pull  it  up- 
wards.  
 To  lower  it,  press  the  lug  then  the  
head restraint.  
 To remove it, place it in the high po- 
sition,  push  the  lug  and  pull  it  up-
wards.  
   T o   r e fi   t   i t ,   e n g a g e   t h e   h e a d   r e s t r a i n t   
rods  in  the  holes  taking  care  to  re-
main  in  the  centreline  of  the  seat 
back. 
 Never drive with the head restraints  
removed,  they  must  be  in  place 
and correctly adjusted.    
Page 42 of 306

59 
3
C O M F O R T
  Storing driving positions  
 System which takes into account the  
settings of the driver's seat, exterior 
mirrors  and  air  conditioning.  It  ena-
bles you to store up to two positions 
using  the  buttons  on  the  side  of  the 
driver's seat.    Storing a position   
  Using buttons M/1/2  
   
     Switch on the ignition. 
  
     Adjust  your  seat  and  your  exte-
rior mirrors. 
  
     Press  button    M ,  then  press  but-
ton   1  or   2  within four seconds.   
  An  audible  signal  is  heard  indi- cating  that  the  storing  has  been  
taken into account.  
 Storing  a  new  position  cancels  the 
previous position.  
  Recalling a stored position   
  Ignition on or engine running  
   
        B r i e fl   y    p r e s s    b u t t o n      1   or    2   to  re-
call the corresponding position.  
 An audible signal is heard indicating  
the end of the adjustment.  
 When  the  ignition  is  on,  after  a  few  
consecutive  position  recalls,  the 
function will be deactivated until the 
engine  is  started,  to  prevent  dis-
charging of the battery.    For  your  safety,  avoid  storing  a 
driving position while driving.  
       REAR HEAD RESTRAINTS 
 The  rear  head  restraints  can  be  re- 
moved and have two positions;  
   -   high, position for use, 
  -   low, storage position.  
 To  raise  a  head  restraint,  pull  it  up- 
wards.  
 To  lower  it,  press  the  lug  then  the  
head restraint.  
 To remove it, place it in the high po- 
sition,  push  the  lug  and  pull  it  up-
wards.  
   T o   r e fi   t   i t ,   e n g a g e   t h e   h e a d   r e s t r a i n t   
rods  in  the  holes  taking  care  to  re-
main  in  the  centreline  of  the  seat 
back. 
 Never drive with the head restraints  
removed,  they  must  be  in  place 
and correctly adjusted.    
Page 43 of 306

60 
3
C O M F O R T
         REAR SEATS 
 Bench  seat,  the  left-hand  (2/3)  or  
right-hand  (1/3)  section  of  which 
can be folded to adapt the boot load 
space.  
  Removing the seat cushion  
   
     Move  the  corresponding  front 
seat forwards if necessary. 
  
     Raise the front of the seat cush-
ion   1 . 
  
     Tilt  the  seat  cushion    1   fully 
against the front seat. 
  
     Remove the seat cushion   1  from 
 i t s   fi   x i n g s   b y   p u l l i n g   u p w a r d s .         Refitting the seat cushion 
   
     Position the seat cushion   1  verti-
 c a l l y   i n   i t s   fi   x i n g s .  
  
     Fold down the seat cushion   1 . 
  
     Press on the seat cushion to se-
cure it.   
  Folding the seat 
 In  order  to  fold  a  rear  seat  without  
any  risk  of  damage,  always  start 
with  the  seat  cushion,    never  with 
the seat back:   
   
     move  the  corresponding  front 
seat forwards if necessary, 
  
    
raise the front of the seat cushion   1 , 
  
     tilt the seat cushion   1  fully against 
the front seat, 
  
     check  that  the  seat  belt  is  posi-
tioned  correctly  on  the  side  of 
the seat back, 
  
     lower  or  remove  the  head  re-
straints if necessary, 
  
     pull  the  control    3   forwards  to  re-
lease the seat back   2 , 
  
     tilt the seat back   2 .  
 The seat cushion   1  can be removed 
to increase the loading volume.     Returning the seat back to its  
original position  
 When returning the rear seat back to  
its original position:  
   
     put the seat back   2  in the upright 
position and secure it, 
  
     fold the seat cushion   1 , 
  
        r e fi   t    t h e    h e a d    r e s t r a i n t s    o r    p u t  
them back in place.  
 When  returning  the  rear  seat  back  
to its original position, take care not 
to  trap  the  seat  belts  and  ensure 
that their buckles are positioned cor-
rectly.  
 The  red  indicator  on  the  control    3  
should  no  longer  be  visible;  if  it  is,  
push the seat fully back.     
Page 94 of 306

98 
6
L A Y O U T
       BOOT LAYOUT (SALOON) 
   
1.    Battery  for  vehicles  with  V6  HDi 
engine. 
  
2.    Pull strap (spare wheel storage).    
3.    Boot lamp. 
  
4.    6 CD changer.     Luggage securing rings  
   
     Use  the  4  securing  rings  on  the 
 b o o t   fl   o o r   t o   s e c u r e   y o u r   l u g g a g e .    
   F o r    s a f e t y    r e a s o n s ,    i n    c a s e    o f    t h e   
 n e e d    f o r    s h a r p    b r a k i n g ,    y o u    a r e  
 a d v i s e d    t o    p l a c e    h e a v y    o b j e c t s    a s  
 f a r   f o r w a r d   i n   t h e   b o o t   a s   p o s s i b l e .