buttons Citroen C5 DAG 2008.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5 DAG, Model: Citroen C5 DAG 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.85 MB
Page 35 of 306
53
3
C O M F O R T
Adjusting the operating duration
Press button 3 and hold it down,
press button 2 or 7 at the same
time. Release button 3 . The time
and symbol 6 fl a s h .
Press again on button 3 and hold
it down, press button 2 or 7 at the
same time. Release button 3 .
The programmed operating du-
ration is displayed and symbol 8
fl a s h e s .
Adjust the operating duration
with button 2 or 7 .
To memorise the setting, press
button 3 or wait until the display
goes off. Immediate start-up
Press button 5 .
The screen displays the symbol 8 and
the remaining operating duration. This
can be adjusted. The maximum dura-
tion is 30 minutes.
The warning lamp 8 lights up and
remains lit for the whole duration of
the system’s operation. The dura-
tion of the system’s operation disap-
pears after 10 seconds.
Start-up of the heating system can
be programmed between 1 minute
and 24 hours in advance.
Adjusting the remaining
operating duration
When the heating mode is active,
the remaining operation duration
c a n b e m o d i fi e d b y b e t w e e n 1 0 a n d
30 minutes using buttons
2 or 7 . Programming the start-up time
You can store up to three different
start-up times, but programme only
one delayed start-up time.
Factory settings
A :
Page 36 of 306
54
3
C O M F O R T
Press button 3 several times
until the programme number
corresponding to the required
programme time is displayed.
The chosen pre-selected time
is activated automatically after
10 seconds if no other buttons
have been pressed.
T o c o n fi r m t h a t t h e m o d e i s a c t i v a t -
ed, symbols 4 and 8 fl a s h u n t i l t h e
heating starts up.
When the heating starts up, the
warning lamp 9 lights up on the
dashboard and the programmer
screen.
Press button 3 b r i e fl y : t h e d i s p l a y
of the start-up time goes off.
In the event of a battery failure, the
factory settings are restored.
Stopping the heating system
while operating
Press button 5 .
The warning lamp 8 and the screen
go out. When a programme is operating,
pressing button
2 or 7 displays the
heating start-up time. A second
press on these buttons displays the
time.
When a programme is not operat-
ing, pressing button 2 or 7 displays
the time.
When the heating is operating, the
remaining operating duration is dis-
played instead of the time.
Page 41 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat, exterior
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat and your exte-
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the storing has been
taken into account.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high po-
sition, push the lug and pull it up-
wards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 42 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
settings of the driver's seat, exterior
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
Adjust your seat and your exte-
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the storing has been
taken into account.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be re-
moved and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high po-
sition, push the lug and pull it up-
wards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to re-
main in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 52 of 306
69
4
A C C E S S
Lost keys
Visit a CITROËN dealer with the vehi-
c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d y o u r
p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The CITROËN dealer will be able to
retrieve the key code and the trans-
ponder code required to order a
replacement key.
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control would
have to be reprogrammed.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reprogramming.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e
electronic engine immobiliser system,
this could cause malfunctions.
When purchasing
a second-hand vehicle
Have the key codes memorised by a
CITROËN dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle.
Do not throw the remote
control batteries away, they
contain metals which are
harmful to the environment.
Take them to an approved collec-
tion point.
Page 54 of 306
69
4
A C C E S S
Lost keys
Visit a CITROËN dealer with the vehi-
c l e ' s V 5 r e g i s t r a t i o n c e r t i fi c a t e a n d y o u r
p e r s o n a l i d e n t i fi c a t i o n d o c u m e n t s .
The CITROËN dealer will be able to
retrieve the key code and the trans-
ponder code required to order a
replacement key.
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons
of your remote control out of range
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control would
have to be reprogrammed.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reprogramming.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Anti-theft protection
D o n o t m a k e a n y m o d i fi c a t i o n s t o t h e
electronic engine immobiliser system,
this could cause malfunctions.
When purchasing
a second-hand vehicle
Have the key codes memorised by a
CITROËN dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle.
Do not throw the remote
control batteries away, they
contain metals which are
harmful to the environment.
Take them to an approved collec-
tion point.
Page 82 of 306
93
V I S I B I L I T Y
5
AMBIENT LIGHTING
Your vehicle is equipped with warm
and welcoming ambient lighting.
A soft orange light is emitted.
Operation
When starting the engine, with the
vehicle lights on, lights located along
the dashboard are activated. Central console
The lights are located on the roof
console, near the front interior lamp.
They light up the central console.
DOOR LIGHTING
Door opening controls
lighting
Dashboard
Operation
These lights are activated with the
automatic switching on of the lights,
when the exterior light is poor. They
are deactivated when the instrument
panel goes out.
The intensity of the lighting varies
along with that of the instrument
panel.
Press buttons A to increase or
reduce the intensity of the lighting. They are located on the front and
rear interior door opening controls.
The rear door opening controls light-
ing is deactivated if child safety is
activated.
Page 83 of 306
93
V I S I B I L I T Y
5
AMBIENT LIGHTING
Your vehicle is equipped with warm
and welcoming ambient lighting.
A soft orange light is emitted.
Operation
When starting the engine, with the
vehicle lights on, lights located along
the dashboard are activated. Central console
The lights are located on the roof
console, near the front interior lamp.
They light up the central console.
DOOR LIGHTING
Door opening controls
lighting
Dashboard
Operation
These lights are activated with the
automatic switching on of the lights,
when the exterior light is poor. They
are deactivated when the instrument
panel goes out.
The intensity of the lighting varies
along with that of the instrument
panel.
Press buttons A to increase or
reduce the intensity of the lighting. They are located on the front and
rear interior door opening controls.
The rear door opening controls light-
ing is deactivated if child safety is
activated.
Page 211 of 306
208
11
22
10101111
131314141515
33445566778899
1212
01 FIRST STEPS
1. On/Off and volume adjustment.
2. CD eject.
3. Selection of the screen display mode.
4. S e l e c t i o n o f t h e s o u r c e : r a d i o a n d C D a n d C D c h a n g e r .
5. Selection of the FM1, FM2, FMast and AM wavebands .
6. S e t t i n g t h e a u d i o o p t i o n s : f r o n t / r e a r b a l a n c e , l e f t / r i g h t balance, loudness, sound ambiences.
7. D i s p l a y i n g o f t h e l i s t o f l o c a l s t a t i o n s , o f t h e t r a c k s o n t h e C D or of the MP3 directories.
8. Abandon current operation.
9. T A ( T r a f fi c A n n o u n c e m e n t ) f u n c t i o n o n / o f f . L o n g p r e s s : a c c e s s t o t h e P T Y ( T Y p e s o f r a d i o P r o g r a m m e ) m o d e .
10. C o n fi r m a t i o n .
11. A u t o m a t i c s e a r c h f o r a l o w e r / h i g h e r f r e q u e n c y . S e l e c t i o n o f p r e v i o u s / n e x t C D o r M P 3 t r a c k .
12. S e l e c t i o n o f a l o w e r / h i g h e r r a d i o f r e q u e n c y . Selection of the previous/next MP3 directory.
13. D i s p l a y i n g o f t h e g e n e r a l m e n u .
14. Buttons 1 to 6: Selection of a stored radio station. L o n g p r e s s : s t o r i n g o f a s t a t i o n .
15. T h e D A R K b u t t o n c h a n g e s t h e d i s p l a y o n t h e s c r e e n t o i m p r o v e d r i v i n g c o m f o r t a t n i g h t . 1 s t p r e s s : l i g h t i n g o f t h e t o p b a n n e r o n l y . 2 n d p r e s s : b l a c k s c r e e n d i s p l a y . 3rd press: return to the standard display.
Page 213 of 306
210
11
22
33
44
22
44
33
11
AUDIO
Press the SOURCE button several times in succession and select the radio.
Press the BAND AST button to select a waveband: FM1, FM2, FMast, AM.
B r i e fl y p r e s s o n e o f t h e b u t t o n s t o carry out an automatic search of the radio stations.
Press one of the buttons to carry out a manual search of the radio stations.
Press the LIST REFRESH button to display the list of stations received l o c a l l y ( 3 0 s t a t i o n s m a x i m u m ) . To update this list, press for more than two seconds.
Select ACTIVATE FREQUENCY F O L L O W I N G ( R D S ) t h e n p r e s s O K . RDS appears on the display.
Select the FM WAVEBAND PREFERENCES function then press OK.
Select AUDIO FUNCTIONS then press OK.
Press the MENU button.
FM WAVEBAND PREFERENCES
ACTIVATE FREQUENCY FOLLOWING (RDS)
T h e e x t e r n a l e n v i r o n m e n t ( h i l l s , b u i l d i n g s , t u n n e l s , b a s e m e n t c a r p a r k s ) m a y b l o c k r e c e p t i o n , i n c l u d i n g in RDS mode. This is a normal effect of the way in which radio waves are transmitted and does not indicate any failure of the audio equipment.
RDS
T h e R D S , i f d i s p l a y e d , e n a b l e s y o u t o c o n t i n u e l i s t e n i n g t o t h e s a m e s t a t i o n b y m e a n s o f f r e q u e n c y f o l l o w i n g . H o w e v e r , i n c e r t a i n c o n d i t i o n s , t h i s R D S s t a t i o n i s n o t f o l l o w e d t h r o u g h o u t t h e c o u n t r y as radio stations do not cover 100 % of the territory. This explains t h e l o s s o f r e c e p t i o n o f t h e s t a t i o n d u r i n g a j o u r n e y .
RADIO
SELECTING A STATION