check engine Citroen C5 DAG 2008.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5 DAG, Model: Citroen C5 DAG 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.85 MB
Page 13 of 306
3 1
1
I N S T R U M E N T S a n d C O N T R O L S
Engine autodiagnostics system I f t h i s c o m e s o n , i t i n d i c a t e s
the occurrence of a fault in
t h e e n g i n e m a n a g e m e n t
s y s t e m .
I f i t fl a s h e s , i t i n d i c a t e s t h e o c c u r r e n c e o f
a f a u l t i n t h e e m i s s i o n c o n t r o l s y s t e m .
Maximum coolant temperature I f t h i s c o m e s o n , i t i n d i c a t e s
t h a t t h e t e m p e r a t u r e i n t h e
c o o l i n g s y s t e m i s t o o h i g h .
S t o p t h e v e h i c l e i m m e d i a t e l y
a n d a s s a f e l y a s p o s s i b l e .
Check the coolant level.
I f t h e l e v e l i s l o w , c o n t a c t a C I T R O Ë N
dealer.
Fuel low
I f t h i s c o m e s o n , i t i n d i c a t e s
t h a t t h e r a n g e r e m a i n i n g
i s a p p r o x i m a t e l y 3 0 m i l e s
( 5 0 k m ) .
I t m a y b e l e s s t h a n t h i s i n c e r t a i n
driving conditions and depending on
the engine.
T h e c a p a c i t y o f t h e t a n k i s a p p r o x i -
m a t e l y 7 1 l i t r e s . Battery charge
I f t h i s c o m e s o n , i t i n d i -
cates the occurrence of a
f a u l t i n t h e b a t t e r y c h a r g i n g
c i r c u i t ( d i r t y o r l o o s e t e r m i -
n a l s , s l a c k o r c u t a l t e r n a t o r
b e l t . . . ) .
Seat belt not fastened/
unfastened *
* A c c o r d i n g t o c o u n t r y .
T h i s w a r n i n g l a m p l i g h t s
u p o n t h e i n s t r u m e n t p a n e l
t o r e m i n d t h e d r i v e r a n d a l l
p a s s e n g e r s t h a t t h e y m u s t
f a s t e n t h e i r s e a t b e l t .
I t i s l i n k e d t o t h e s e a t b e l t i n f o r m a -
t i o n g i v e n b y t h e r o o f c o n s o l e . Seat belt non-fastening/
unfastening
T h i s w a r n i n g l a m p
i n f o r m s y o u o f t h e
non-fastening and
unfastening of the
d r i v e r a n d p a s s e n g e r s e a t b e l t s .
The lit up positions represent the
p a s s e n g e r s w h o s e s e a t b e l t s a r e
n o t f a s t e n e d / u n f a s t e n e d .
D r i v e r ’ s s e a t b e l t n o t f a s t e n e d :
- T h e w a r n i n g l a m p l i g h t s u p b e - t w e e n 0 a n d 1 2 m p h ( 2 0 k m / h ) .
A b o v e 1 2 m p h , i t fl a s h e s a c c o m p a -
n i e d b y a s o u n d s i g n a l f o r a r o u n d
1 2 0 s e c o n d s .
F r o n t a n d r e a r p a s s e n g e r s e a t b e l t s
not fastened:
-
W h e n t h e i g n i t i o n i s s w i t c h e d o n ,
the points corresponding to the seat
p o s i t i o n s w i t h s e a t b e l t s n o t f a s -
t e n e d r e m a i n l i t u p f o r 3 0 s e c o n d s .
S e a t b e l t s u n f a s t e n e d d u r i n g t h e
j o u r n e y :
- The point corresponding to the s e a t p o s i t i o n w i t h s e a t b e l t u n -
f a s t e n e d l i g h t s u p b e t w e e n 0 a n d
1 2 m p h ( 2 0 k m / h ) . A b o v e 1 2 m p h ,
i t fl a s h e s a c c o m p a n i e d b y a s o u n d
s i g n a l f o r a r o u n d 1 2 0 s e c o n d s .
The sound signal stops when the
s e a t b e l t i s r e - f a s t e n e d o r i f a d o o r
is opened.
Page 26 of 306
44
3
C O M F O R T
Air conditioning
We recommend use of the automatic
regulation of the air conditioning.
It permits automatic and optimised
control of all of the following func-
t i o n s : a i r fl o w , t e m p e r a t u r e i n t h e
passenger compartment and air
distribution, by means of various
sensors (exterior temperature, sun-
shine). This eliminates any need for
you to change your settings other
than the value displayed.
Please do not block the sunshine
sensor A .
If you select the automatic mode
(by pressing the "AUTO" control)
and leave all of the vents open, opti-
mum comfort will be maintained and
humidity and condensation will be
removed regardless of the exterior
climatic conditions.
The temperature in the passenger
compartment cannot be lower than
the exterior temperature if the air
conditioning is not on.
VENTILATION, HEATING AND AIR CONDITIONING RECOMMENDATIONS
In order to be effective, the air con-
ditioning must be used with the win-
dows closed. If the vehicle has been
parked in the sun for a long period
and the interior temperature is very
high, ventilate the passenger com-
partment with the windows open for
a few minutes, then close the win-
dows.
To keep the air conditioning system
in good working order it is essential
that it is operated at least once a
month.
The air conditioning uses the en-
gine power during its operation. As a
result, the fuel consumption of the
vehicle increases.
In certain cases of particularly ardu-
ous use (e.g. towing the maximum
load on a steep gradient in high tem-
peratures), switching off the air condi-
tioning permits the recovery of engine
power and therefore increases the
towing capacity.
Air inlet
Check that the exterior grille for the air
inlet, at the bottom of the windscreen,
is clean and free of dead leaves,
snow, etc.
When washing the vehicle using a high
pressure nozzle, avoid spraying at the
air inlet. Air circulation
Maximum comfort is obtained by
means of a good distribution of air in
the passenger compartment, both in
the front and in the rear.
To obtain a uniform distribution of
air, take care not to block the ex-
terior air intake grille located at the
base of the windscreen, the vents,
the air outlets under the front seats
and the air extractor located behind
t h e fl a p s i n t h e b o o t .
T h e f r o n t a n d r e a r v e n t s a r e fi t t e d
with thumbwheels to adjust the air
fl o w a n d d i r e c t i o n . W e r e c o m m e n d
that you leave all of the vents open.
Dust filter/Odour filter
(active carbon)
T h e r e i s a fi l t e r f o r e x c l u d i n g o d o u r s
and dust.
T h i s fi l t e r h a s t o b e c h a n g e d i n a c -
cordance with the vehicle mainte-
nance schedule (see: "Maintenance
and Warranty Guide").
Page 121 of 306
123
9
D R I V I N G
ELECTRONIC PARKING BRAKE
The electronic parking brake com-
bines 2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Permanent manual application/ release of the parking brake is
possible by pulling control A
while pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake
is automatically applied
when the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y : Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by
pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message "parking
brake applied" on the instrument
panel display.
A n o p e r a t i o n s o u n d w i l l c o n fi r m t o
you the application/release of your
electronic parking brake. - the lighting of warning
lamp P on control A and
on the instrument panel,
- the display of a message "park- ing brake applied" on the instru-
ment panel display.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Page 128 of 306
129
9
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back fault " and of the follow-
ing warning lamps:
and/or fl a s h i n g
- The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electronic parking brake:
Immobilise the vehicle and switch off the ignition
Pull the control lever for at least 5 seconds or un til maximum application.
Switch on the ignition and check that the electronic parkin g
brake warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electronic parking brake:
Switch on the ignition.
Push the control lever and hold it for approximately 3 seconds.
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electronic parking brake and
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
Wait approximately 3 minutes.
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning la
mp makes it essential to stop the
v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r v e h i c l e .
- Apply the electronic parking brake before switching off the en-
gine.
Page 130 of 306
131
9
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the key
to position M and wait until the
pre-heating warning light switch-
es off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch whilst turning the starter
to facilitate starting.
Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob
and push the gear lever to the
left then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
AUTOMATIC GEARBOX
Automatic gearbox which offers a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Therefore, you have a choice of four
driving modes:
- automatic operation for elec-
tronic control of the gears by the
gearbox,
- the SPORT programme for a
more dynamic driving style,
- the SNOW programme to im-
prove driving when the grip is
poor,
- manual operation for sequen-
tial changing of the gears by the
driver.
Page 131 of 306
131
9
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the key
to position M and wait until the
pre-heating warning light switch-
es off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch whilst turning the starter
to facilitate starting.
Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring under the knob
and push the gear lever to the
left then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
AUTOMATIC GEARBOX
Automatic gearbox which offers a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Therefore, you have a choice of four
driving modes:
- automatic operation for elec-
tronic control of the gears by the
gearbox,
- the SPORT programme for a
more dynamic driving style,
- the SNOW programme to im-
prove driving when the grip is
poor,
- manual operation for sequen-
tial changing of the gears by the
driver.
Page 133 of 306
133
D R I V I N G Never select positions P or
R if the vehicle is not sta-
tionary.
If, while the vehicle is mov-
ing, position N is engaged inad-
vertently, allow the engine to idle
before engaging position D or M .
Moving off
To start the engine, the selector
has to be in position P or N .
Action the starter.
When the engine is running,
place the selector on R , D or M
as required.
Check, in the instrument panel,
the position engaged.
Release the brake pedal and ac-
celerate.
To avoid incoherence between
the position of the selector and
the actual position of the gear-
box, always exit from position P
when you switch on the ignition
and press the brake pedal.
Otherwise, when the ignition is on or
the engine is running:
reposition the selector in position P ,
put your foot on the brake ped-
al and then select the gear you
want. Park
This position of the selector
is used to prevent the vehi-
cle from moving when you
are stationary.
To select position P, move the
selector back to the highest po-
sition (towards R ), then push it
forwards and then to the left.
To exit position P , move the se-
lector to the right and then to the
position you want.
Only engage this position when
the vehicle is completely sta-
tionary. In this position, the front
wheels are locked. Make sure
that the selector is correctly po-
sitioned. Reverse gear
Only engage this position
when the vehicle is station-
ary. To prevent snatching,
do not accelerate too soon
after selection.
Neutral Never select position N if
the vehicle is moving.
Page 139 of 306
139
9
D R I V I N G In the event of a steep descent or
under excessive acceleration, the
speed limiter (which does not act
on the brakes) may not be able to
prevent the vehicle from exceeding
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
of-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed dis-
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
to return below the maximum speed,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
cle from exceeding the programmed
speed (e.g. on a steep descent or
under excessive acceleration).
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed. Return to normal driving
Press on button 5 .
Select the speed limiter function.
Or stop the engine.
Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
a sound signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 141 of 306
141
9
D R I V I N G Cruise control must only be
u s e d w h e r e t h e t r a f fi c c o n -
ditions permit driving at a
constant speed.
Do not use it on congested roads
or when the weather or the road
conditions are poor.
The driver still has to remain atten-
tive and in complete control of his
vehicle.
Y o u a r e r e c o m m e n d e d t o k e e p y o u r
feet within range of the pedals.
Overriding the programmed
speed
While cruise control is in operation,
it is always possible to go above the
programmed speed simply by press-
ing the accelerator pedal (for exam-
ple to overtake another vehicle).
The speed displayed in zone
A
fl a s h e s .
Y o u o n l y h a v e t o r e l e a s e t h e a c -
celerator pedal to return to the pro-
grammed speed.
Suspension/Resumption
Either by pressing the brake
pedal or the clutch pedal.
Or by pressing button 3 .
Or by the ESP or ASR systems
being active.
For vehicles with a manual gearbox,
cruise control is deactivated if the
gear lever is in neutral. Reactivation
-
By recalling the memorised
speed
After deactivation, press button 3 .
Y o u r v e h i c l e a u t o m a t i c a l l y r e t u r n s
to the memorised cruising speed.
The memorised speed and "ON"
are displayed in zone A .
If the memorised cruising speed is higher than the current speed,
the vehicle will accelerate strong-
ly to reach the current speed.
- By selecting the current speed
Press button 1 or 2 once the de-
sired speed has been reached.
The new speed and "ON" will
appear in zone A .
Return to normal driving
Press on button 5 .
Select the cruise control function.
Or stop the engine.
The speed that was chosen is no
longer memorised.
"PAUSE" will be displayed in zone
A of the instrument panel.
These actions do not cancel the
cruising speed which remains dis-
played on the instrument panel. Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
a sound signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 153 of 306
153
10
C H E C K S
PETROL ENGINES
They allow you access for checking
t h e l e v e l o f t h e v a r i o u s fl u i d s a n d f o r
replacing certain components.
1. Screenwash and headlamp
wash reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r .
3. Coolant reservoir.
4. Dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
V e h i c l e s fi t t e d w i t h t h e 2.0i
16V e n g i n e m a y b e fi t t e d
with metal suspension. In
this case, a different power steer-
i n g fl u i d r e s e r v o i r i s fi t t e d .
1.8i 16V
2.0i 16V