light Citroen C5 DAG 2010.5 (RD/TD) / 2.G Service Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010.5, Model line: C5 DAG, Model: Citroen C5 DAG 2010.5 (RD/TD) / 2.GPages: 336, PDF Size: 18.85 MB
Page 153 of 336
IX
132
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the following
warning lamps:
and/or fl a s h i n g - The automatic functions are deactivated.
- The hill start assist is not available.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
P u l l t h e c o n t r o l l e v e r f o r a t l e a s t 5 s e c o n d s o r u n t i l m a x i m u m
application.
S w i t c h o n t h e i g n i t i o n a n d c h e c k t h a t t h e e l e c t r i c p a r k i n g b r a k e
warning lamps are on.
- Application may take longer than in normal operation.
- I f w a r n i n g l a m p ( ! ) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
S w i t c h o n t h e i g n i t i o n .
P u s h t h e c o n t r o l l e v e r a n d h o l d i t f o r a p p r o x i m a t e l y 3 s e c o n d s .
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
W a i t a p p r o x i m a t e l y 3 m i n u t e s .
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switching off the engine.
Page 171 of 336
IX
150
D R I V I N G
In the event of a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n , t h e
speed limiter (which does not act
on the brakes) may not be able to
p r e v e n t t h e v e h i c l e f r o m e x c e e d i n g
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
m e m o r i s e d m a x i m u m s p e e d w h i c h
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
o f - t r a v e l s w i t c h . I n o r d e r t o e x c e e d
t h e m e m o r i s e d m a x i m u m s p e e d a t
any time, you can press the pedal
all the way down. While the speed
i s b e i n g e x c e e d e d , t h e s p e e d d i s -
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
t o r e t u r n b e l o w t h e m a x i m u m s p e e d ,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
c l e f r o m e x c e e d i n g t h e p r o g r a m m e d
speed (e.g. on a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n ) .
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed. Return to normal driving
Either press on button 5 .
Or select the speed limiter function.
Or stop the engine.
Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 172 of 336
IX
151
D R I V I N G
CRUISE CONTROL
S y s t e m w h i c h a u t o m a t i c a l l y m a i n -
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must be
at least 25 mph (40 km/h) and you
must be in at least:
- 4 t h g e a r f o r m a n u a l g e a r b o x e s ,
- 2 n d g e a r f o r a u t o m a t i c g e a r b o x e s . Displays on the instrument
panel
The programmed information is
grouped together in zone
A of the
instrument panel.
Programming
Press button 4 to select cruise
control mode " CRUISE ".
Steering mounted controls
The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. T h e s e l e c t i o n i s c o n fi r m e d b y t h e
display of the function in zone
A of
the instrument panel.
When the function is selected, no
cruising speed has yet been
memorised . Once the desired speed has been
reached using the accelerator, press
button
1 or button 2 . The cruising
speed is then memorised and cruise
control is activated. The cruising
speed is displayed in zone A of the
instrument panel, and "ON" is dis-
played.
Adjustment of the memorised
speed while cruise control is
in operation
You can adjust the memorised speed, displayed in zone A , by pressing:
- Button 1 to increase the speed.
- Button 2 to reduce the speed.
S u c c e s s i v e p r e s s e s w i l l m o d i f y t h e
cruise speed in steps of 1 mph and a
continuous press in steps of 5 mph.
You can then release the accelera-
tor pedal. The vehicle will automati-
cally keep to the speed chosen.
The vehicle speed may vary slightly
from that memorised.
If during cruise control the system
cannot keep to the cruise speed
(e.g. on a steep descent), then the
s p e e d fl a s h e s . I f n e c e s s a r y , b r a k e t o
curb your speed.
Page 173 of 336
IX
!
152
D R I V I N G
Cruise control must only be
u s e d w h e r e t h e t r a f fi c c o n d i -
tions permit driving at a con-
stant speed .
Do not use it on congested
roads or when the weather or the
road conditions are poor .
The driver must remain attentive
and in complete control of the ve-
hicle .
You are recommended to keep your
feet within range of the pedals .
Overriding the programmed
speed
While cruise control is in operation,
it is always possible to go above the
programmed speed simply by press-
i n g t h e a c c e l e r a t o r p e d a l ( f o r e x a m -
ple to overtake another vehicle).
The speed displayed in zone
A
fl a s h e s .
You only have to release the ac-
celerator pedal to return to the pro-
grammed speed.
Suspension/Resumption
Either by pressing the brake
pedal or the clutch pedal.
Or by pressing button 3 .
O r b y t h e E S P o r A S R s y s t e m s
being active.
F o r v e h i c l e s w i t h a m a n u a l g e a r b o x ,
cruise control is deactivated if the
gear lever is in neutral. Reactivation
-
By recalling the memorised
speed
After deactivation, press button 3 .
Your vehicle automatically returns
to the memorised cruising speed.
The memorised speed and "ON"
are displayed in zone A .
If the memorised cruising speed is higher than the current speed,
the vehicle will accelerate strong-
ly to reach the current speed.
- By selecting the current speed
Press button 1 or 2 once the de-
sired speed has been reached.
The new speed and "ON" will
appear in zone A .
Return to normal driving
Either press on button 5 .
Or select the cruise control function.
Or stop the engine.
The speed that was chosen is no
longer memorised.
"PAUSE" will be displayed in zone A
of the instrument panel.
These actions do not cancel the
cruising speed which remains dis-
played on the instrument panel. Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 184 of 336
X
!
163
C H E C K S
RUNNING OUT OF FUEL (DIESEL)
HDi 110 engine
Unclip the protective cover to gain
access to the priming pump. HDi 140 and HDi 160 engines
Unclip the protective cover to gain
access to the priming pump.
Priming the fuel system
In the event of running out of fuel:
a f t e r fi l l i n g ( m i n i m u m 5 l i t r e s )
and removing the protective cover,
operate the manual priming pump,
until some resistance is felt,
operate the starter motor while
depressing the accelerator pedal
slightly until the engine starts. HDi engines make use of ad-
vanced technology.
All maintenance and repairs re-
q u i r e s p e c i a l q u a l i fi c a t i o n s w h i c h
only a CITROËN dealer can guar-
antee.
V6 HDi 240 engine with electric
pump
In the event of running out of fuel:
after adding fuel, turn the ignition
key to position M , wait for a few
seconds,
operate the starter motor until
the engine starts.
If the engine fails to start after sev-
eral attempts, contact a CITROËN
dealer.
I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t
a t t e m p t , w a i t fi f t e e n s e c o n d s b e f o r e
trying again.
If the engine fails to start after a few
attempts, operate the priming pump
again and then try to start the en-
gine.
When the engine is idling, acceler-
ate slightly to complete the bleeding
of the circuit.
Page 190 of 336
X
!
169
C H E C K S
Screenwash and headlamp
wash fluid
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e
topped up or replaced with water.
Reservoir capacities:
- s c r e e n w a s h : a p p r o x i m a t e l y 3 . 5 l i -tres,
- screenwash and headlamp wash: a p p r o x i m a t e l y 6 . 1 5 l i t r e s . Diesel additive level
(Diesel engine with particle
emission filter)
A low additive level is indicated by
lighting of the service warning lamp,
accompanied by an audible warning
and a message on the multifunction
screen.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
u s e d o i l o r fl u i d s w i t h t h e
skin.
M o s t o f t h e s e fl u i d s a r e h a r m f u l t o
health or indeed very corrosive.
D o n o t d i s c a r d u s e d o i l o r fl u -
ids into sewers or onto the
ground.
Take used oil to a CITROËN deal-
er (France) or an authorised waste
disposal site.
I n t h e c a s e o f v e h i c l e s fi t t e d
with headlamp washers, the
m i n i m u m l e v e l o f t h i s fl u i d i s
indicated by an audible sig-
nal and a message on the multifunc-
tion screen.
Top up the level when you stop the
vehicle.
Coolant level
Coolant change
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the
manufacturer's recommendations. The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
a p a r t i c l e e m i s s i o n fi l t e r , t h e f a n
may operate after the vehicle has
been switched off, even if the en-
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.
Page 191 of 336
X
170
C H E C K S
CHECKS
Unless otherwise indicated, check
these components in accordance
with the Maintenance and Warranty
Guide and according to your en-
gine.
Otherwise, have them checked by a
CITROËN dealer.
Battery The battery does not re-
quire any maintenance.
However, check that the
terminals are clean and cor-
rectly tightened, particularly
in summer and winter.
When carrying out work on the bat-
tery, refer to the "Practical infor-
mation" section for details of the
precautions to be taken before dis-
connecting the battery and following
its reconnection.
Air filter and passenger compartment filter
Refer to the Maintenance
and Warranty Guide for
details of the replacement
intervals for these compo-
nents.
Depending on the environment (e.g.
dusty atmosphere) and the use of
the vehicle (e.g. city driving), replace
them twice as often if necessary
(refer to the "Engines" section).
A clogged passenger compartment
fi l t e r m a y h a v e a n a d v e r s e e f f e c t o n
the performance of the air condition-
ing system and generate undesir-
able odours.
Oil filter
R e p l a c e t h e o i l fi l t e r e a c h
time the engine oil is
changed. Particle filter system (Diesel)
Complementary to the catalytic
c o n v e r t e r , t h i s fi l t e r m a k e s a n a c -
tive contribution to the preservation
of air quality by the retaining of the
unburnt pollutant particles. Black
exhaust fumes are thus no longer
emitted.
After prolonged idling or driving at very
low speeds, you may occasionally no-
tice water vapour being emitted from
the exhaust when accelerating. This
is of no consequence to the running of
the vehicle or to the environment.
If there is risk of clogging, a mes-
sage appears on the instrument
panel display, accompanied by an
audible signal and lighting of the
service warning lamp.
This alert tells you that the particle
fi l t e r i s s t a r t i n g t o fi l l u p ( i n c o n d i -
tions of urban driving of excep-
tionally long duration: low speeds,
t r a f fi c j a m s e t c . ) .
T o r e g e n e r a t e t h e fi l t e r , i t i s a d v i s e d
to drive as soon as possible, when
t r a f fi c c o n d i t i o n s p e r m i t , a t a s p e e d
of 40 mph (around 60 km/h) or
m o r e f o r a t l e a s t fi v e m i n u t e s ( u n t i l
the alert message disappears).
If this alert persists, consult a
CITROËN dealer.
Refer to the Maintenance and
Warranty Guide for details of the re-
placement interval for this component.
The presence of this label, in par-
ticular with the Stop & Start system,
i n d i c a t e s t h e u s e o f a s p e c i fi c 1 2 V
lead-acid battery with special tech-
n o l o g y a n d s p e c i fi c a t i o n , f o r w h i c h
the involvement of a CITROËN
dealer is required when replacing or
disconnecting the battery.
Failure to observe this recommen-
dation may cause premature wear
of the battery.
Page 201 of 336
XI
!
179
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB Headlamps
Model with Xenon headlamps (D1S)
1. Sidelamps: W5W
2. Dual-function Xenon
headlamps (dipped/main): D1S
3. Cornering
lighting: HP19
4. Daytime running lamps: HP24
F o r t h e m a i n t e n a n c e o f t h e f r o n t
h e a d l a m p u n i t a n d t h e c h a n g i n g o f
H P 1 9 , D 1 S a n d H P 2 4 b u l b s , c o n t a c t
a C I T R O Ë N d e a l e r .
Risk of electrocution
X e n o n b u l b s m u s t b e r e p l a c e d b y a
C I T R O Ë N d e a l e r .
You are advised to change both
D 1 S b u l b s a t t h e s a m e t i m e , i f o n e
o f t h e m h a s f a i l e d .
T h e h e a d l a m p s a r e fi t t e d w i t h
p o l y c a r b o n a t e g l a s s w i t h a
p r o t e c t i v e c o a t i n g :
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,
u s e a s p o n g e a n d s o a p y w a t e r ,
w h e n u s i n g a h i g h p r e s s u r e
w a s h e r o n p e r s i s t e n t m a r k s , d o
n o t d i r e c t a t t h e l a m p s o r t h e i r
o u t l i n e s f o r t o o l o n g , s o a s n o t
t o d a m a g e t h e i r p r o t e c t i v e c o a t -
i n g a n d s e a l s .
D o n o t t o u c h t h e b u l b d i r e c t l y
w i t h y o u r fi n g e r s , u s e l i n t - f r e e
c l o t h s .
C h a n g i n g a b u l b s h o u l d o n l y b e
d o n e a f t e r t h e h e a d l a m p h a s b e e n
s w i t c h e d o f f f o r a f e w m i n u t e s ( r i s k
o f s e r i o u s b u r n s ) .
I t i s i m p e r a t i v e t o u s e o n l y a n t i -
u l t r a v i o l e t ( U V ) t y p e b u l b s i n o r d e r
n o t t o d a m a g e t h e h e a d l a m p .
A l w a y s r e p l a c e a f a i l e d b u l b w i t h a
n e w b u l b w i t h t h e s a m e t y p e a n d
s p e c i fi c a t i o n .
Page 202 of 336
XI
1 8 0
P R A C T I C A L I N F O R M A T I O N
Main beams
R e m o v e t h e p r o t e c t i v e c a p A .
D i s e n g a g e t h e r e t a i n i n g s p r i n g .
R e m o v e t h e b u l b a n d r e p l a c e i t ,
p a y i n g a t t e n t i o n t o t h e d i r e c t i o n
o f fi t t i n g .
R e fi t t h e r e t a i n i n g s p r i n g .
R e fi t t h e p r o t e c t i v e c a p A .
Model with halogen headlamps
1. Main beams: H1
2. Sidelamps: W5W
3. Dipped beams: H7
4. Directional lighting: H7
5. Daytime running lamps: HP24
F o r t h e m a i n t e n a n c e o f t h e f r o n t
h e a d l a m p u n i t a n d c h a n g i n g H P 2 4
b u l b s , c o n t a c t a C I T R O Ë N d e a l e r .
Sidelamps
R e m o v e t h e p r o t e c t i v e c a p A .
P u l l t h e b u l b h o l d e r t o r e m o v e i t .
R e p l a c e t h e b u l b a n d r e fi t t h e
b u l b h o l d e r .
R e fi t t h e p r o t e c t i v e c a p A .
Page 211 of 336
XI
1 8 8
P R A C T I C A L I N F O R M A T I O N
Interior lamps
Roof lamps
U n c l i p t h e t r a n s p a r e n t c o v e r o f
t h e r o o f l a m p t o r e a c h t h e b u l b .
Bulb: W5W
Rear reading lamps (Tourer)
Detach the cover of the reading
l a m p t o a c c e s s t h e b u l b .
Bulb: W5W
Map reading lamp
D e t a c h t h e c o v e r .
I f n e c e s s a r y , d e t a c h t h e p a r t i t i o n
o f t h e a f f e c t e d m a p r e a d i n g l a m p . Boot lamp
Detach the cover and use a W5W
b u l b .
Pavement lighting
Detach the cover and use a W5W
b u l b . Floor lighting
Detach the cover and use a W5W
b u l b .
Glovebox
Detach the cover and use a W5W
b u l b .