Citroen C5 RHD 2011.5 (RD/TD) / 2.G Repair Manual
Manufacturer: CITROEN, Model Year: 2011.5, Model line: C5 RHD, Model: Citroen C5 RHD 2011.5 (RD/TD) / 2.GPages: 340, PDF Size: 39.33 MB
Page 61 of 340
III
59
COMFORT
Setting the time
Once the time has been displayed,
by means of the buttons 1
, press
buttons 4
and 5
simultaneously with-
in 10 seconds.
Immediate activation
Press button 5
(ON) until the mes-
sage "OK"
appears.
When the signal has been received,
the message "OK"
is displayed
along with the duration of operation. Press the buttons 1
to display the
duration of operation.
This symbol fl ashes.
Set the time using the buttons 1
.
Press buttons 4
and 5
simultaneously
to save it.
This symbol is displayed (fi xed).
The heater starts and this
symbol is displayed.
To deactivate the function, press
button 4
(OFF) until the message
"OK"
appears.
This symbol is switched off.
When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
Setting the duration
of operation
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4
and
5
simultaneously within 10 seconds.
This symbol fl ashes.
Set the duration by pressing the
buttons 1
(adjustment in steps of
10 mins and max value 30 mins).
Press buttons 4
and 5
simultaneously
to save the duration of operation.
This symbol is displayed (fi xed).
The factory setting value is 30 minutes.
Page 62 of 340
III
60
COMFORT
Programming the heating
You must programme your depar-
ture time in order for the system to
calculate the optimum heater start
time automatically.
Programming the departure time
Press the buttons 1
to display the
programming time.
Activation - deactivation
Once the programming time has
been displayed by means of the but-
tons 1
, press button 5
(ON) until the
message "OK"
appears.
This symbol is displayed.
Once the programming time has
been displayed, press buttons 4
and
5
simultaneously within 10 seconds.
This symbol fl ashes.
Set the time by pressing the buttons 1
and press buttons 4
and 5
simultane-
ously to save it.
This symbol is displayed (fi xed).
This symbol is displayed when
the heater starts.
HTM: Heat Thermo Management.
When the signal has been received,
the message "OK"
is displayed along
with the symbol "HTM"
.
To deactivate the programming,
press button 4
(OFF) until the mes-
sage "OK"
appears.
The symbol "HTM"
is switched off.
When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
Switching off the heating
Press button 5
(ON).
The symbol "HTM"
remains on.
Changing the level of heating
The system offers 5 levels
of heat-
ing (from the lowest level C1
to the
highest level C5
).
Once the level of heating has been
displayed by means of the buttons 1
,
press buttons 4
and 5
simultaneously.
The letter "C"
fl ashes.
Set the level of heating by pressing
the buttons 1
.
Press buttons 4
and 5
simultane-
ously to save the level selected. The
letter "C"
is displayed (fi xed).
The factory pre-sets are replaced
by the new settings entered. The
programmed times are stored until
the next time they are changed.
When the departure time is acti-
vated, the level of heating cannot
be changed. The departure time
must be deactivated fi rst.
Page 63 of 340
III
!
61
COMFORT
Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be
reinitialised, see below.
Always switch off the program-
mable heating while fi lling with
fuel to avoid any risk of fi re or
explosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
infl ammable surface (dry grass,
dead leaves, paper…), there is a
risk of fi re.
The programmable heating system
is supplied by the vehicle's fuel tank.
Before use, ensure that the quantity
of fuel remaining is suffi cient. If the
fuel tank is at the reserve, we strong-
ly advise that you do not programme
the heating.
Do not discard the used
batteries, take them to an
approved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnected
or the remote control's battery is re-
placed, the remote control must be
reinitialised.
After switching on the power, press
button 4
(OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK"
is displayed on the remote
control screen.
If a problem occurs, the message
"FAIL"
appears. Repeat the operation.
In addition, your programmable
heating can be used to pre-heat
your vehicle's passenger com-
partment.
The interior volumetric protection
alarm movement sensor may be
disturbed by the fl ow of air from
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.
Page 64 of 340
III
62
COMFORT
FRONT SEATS MANUAL ADJUSTMENTS
1.
Adjustments to the height and
angle of the head restraint
To raise it, pull upwards.
To lower it, press on the control A
to unlock it, and simultaneously
on the head restraint itself. The
adjustment is correct when the
top edge of the head restraint is
at the same height as the top of
the head. It is also tilt adjustable.
To raise it, press control A
to
unlock it, then pull it upwards.
It may be necessary to adjust the
backrest angle.
2.
Adjustment of the backrest angle
Operate the control and adjust
the position of the backrest to
the front or to the rear.
3.
Adjustment of the seat height
Raise or lower the control the
number of times required to
obtain the desired position.
4.
Longitudinal adjustment of seat
Lift the control bar and adjust to
the desired position.
5.
Adjustment of lumbar support
Turn the control and adjust to the
desired position.
6.
Heated seat controls
The heated seats only operate
when the engine is running. Seat consisting of a seat cushion, seat back and head restraint which can all be
adjusted for optimum driving comfort.
For your safety, do not drive with
the head restraints removed; they
must be in place and correctly
adjusted.
Page 65 of 340
III
63
COMFORT
FRONT SEATS
ELECTRIC ADJUSTMENTS
To adjust the electric seats, switch on the ignition or start the engine if the
vehicle has gone into economy mode.
Seat adjustments are also possible for a short period after opening one of the
front doors or switching off the ignition.
2.
Adjustment of the backrest angle
Move the control forwards or
backwards to adjust the backrest
angle.
3.
Adjustment of the angle of the
top of the backrest
Move the control forwards or
backwards to adjust the angle of
the top of the backrest.
1.
Adjustment of the seat height
and angle, and longitudinal
adjustment
)
Raise or lower the front of the
control to adjust the seat cushion
angle.
)
Raise or lower the rear of the
control to raise or lower the seat.
)
Simultaneously raise or lower
the front and rear of the control
in order to raise or lower the
entire seat.
4.
Adjustment of lumbar support
This function allows you to inde-
pendently adjust the height and
level of lumbar support.
Move the control:
)
Forwards or backwards to increase
or reduce the lumbar support.
)
Upwards or downwards to raise or
lower the lumbar support zone.
Head restraint height and
angle adjustments on electric
seats
)
To adjust the angle of the head
restraint, push back or pull for-
ward section C
of the head re-
straint until you reach the desired
position.
)
To raise it, pull upwards.
)
To lower it, press on the control D
to unlock it, and simultaneously
on the head restraint itself.
)
To remove it, press on the
control D
to unlock it, then pull it
upwards.
Page 66 of 340
III
64
COMFORT
This function provides the driver with
a back massage. It only operates
when the engine is running.
)
Press on button A
.
The warning lamp comes on and the
massage function is activated for a
period of 1 hour. During this time,
massage is performed in cycles of
6 minutes (4 minutes of massage fol-
lowed by 2 minutes break). In total,
the system will perform 10 cycles.
After 1 hour, the function is deacti-
vated. The warning lamp goes out.
Massage function
Welcome function
The welcome function assists entry
and leaving the vehicle.
After switching off the ignition and
opening the driver’s door, the seat
moves back automatically and then
stays in this position, ready for the
next entry to the vehicle.
When switching on the ignition, the
seat moves forward to the memo-
rised driving position.
When moving the seat, take care
that no person or object hinders the
automatic movement of the seat.
This function is deactivated by de-
fault. You may activate or deactivate
this function using the "Main Menu"
on the instrument panel screen. To
do so, select "Vehicle parameters/
Comfort/Driver welcome".
Deactivation
You can deactivate the massage
function at any time by pressing on
button A
.
Heated seats control
With the engine running, the front
seats can operate separately.
)
Use the corresponding adjust-
ment dial, placed on the outer
side of each front seat, to switch
on and select the level of heating
required:
0
: Off.
1
: Low.
2
: Medium.
3
: High.
Page 67 of 340
III
65
COMFORT
Storing driving positions
System which stores the settings of
the driver's seat and air conditioning.
Up to two positions can be stored
using the buttons on the side of the
driver's seat.
Storing a position
Using buttons M/1/2
)
Switch on the ignition.
)
Adjust your seat.
)
Press button M
, then press but-
ton 1
or 2
within four seconds.
An audible signal confi rms that the
settings have been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
)
Briefl y press button 1
or 2
to re-
call the corresponding position.
An audible signal indicates the end
of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery.
For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions:
- high, position for use,
- low, storage position.
To raise a head restraint, pull it up-
wards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high posi-
tion, push the lug and pull it upwards.
To r efi t it, engage the head restraint
rods in the holes taking care to re-
main in line with the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Page 68 of 340
III
66
COMFORT
REAR SEATS
Bench seat, the left-hand (2/3) or
right-hand (1/3) section of which
can be folded to adapt the boot load
space.
Removing the seat cushion
)
Move the corresponding front
seat forwards if necessary.
)
Raise the front of the seat cushion 1
.
)
Tilt the seat cushion 1
fully
against the front seat.
)
Remove the seat cushion 1
from
its fi xings by pulling upwards.
Refitting the seat cushion
)
Position the seat cushion 1
verti-
cally in its fi xings.
)
Fold down the seat cushion 1
.
)
Press on the seat cushion to
secure it.
Folding the seat
In order to fold a rear seat without
any risk of damage, always start
with the seat cushion, never with
the seat back:
)
move the corresponding front
seat forwards if necessary,
)
raise the front of the seat cushion 1
,
)
tilt the seat cushion 1
fully against
the front seat,
)
check that the seat belt is posi-
tioned correctly on the side of
the seat back,
)
lower or remove the head re-
straints if necessary,
)
pull the control 3
forwards to re-
lease the seat back 2
,
)
tilt the seat back 2
.
The seat cushion 1
can be removed
to increase the loading volume.
Returning the seat back to its
original position
When returning the rear seat to its
original position:
)
put the seat back 2
in the upright
position and secure it,
)
fold the seat cushion 1
,
)
refi t the head restraints or put
them back in place.
When returning the rear seat to its
original position, take care not to trap
the seat belts and ensure that their
buckles are positioned correctly.
The red indicator on the control 3
should no longer be visible; if it is,
push the seat fully back.
Page 69 of 340
III
67
COMFORT
MIRRORS
Door mirrors
Each fi tted with an adjustable mirror
glasses providing the lateral rear-
ward vision necessary for overtaking
or parking. They can also be folded.
Adjustment
With the ignition on:
)
move control A
to the right or to
the left to select the corresponding
mirror,
)
move control B
in all four direc-
tions to adjust,
)
return control A
to the central position. Demisting/defrosting of the door
mirrors is associated with that of
the rear screen.
Folding
)
from outside; lock the vehicle
using the remote control or the
key.
)
from inside; with the ignition on,
pull control A
rearwards.
If the mirrors are folded using con-
trol A
, they will not unfold when the
vehicle is unlocked. Control A
must
be pulled again.
Unfolding
)
from outside; unlock the vehicle
using the remote control or the
key.
)
from inside; with the ignition on,
pull control A
rearwards.
If the position is changed manually,
a long press on control A
re-engages
the mirror.
The folding and unfolding of the door
mirrors using the remote control can
be deactivated by a CITROËN dealer
or a qualifi ed workshop.
The objects observed are, in reality,
closer than they appear.
Take this into account in order to
correctly judge the distance of ve-
hicles approaching from behind.
Rear view mirror
Adjustable mirror providing a central
rearward view.
Equipped with an anti-dazzle sys-
tem, which darkens the mirror glass:
this reduces the nuisance to the
driver caused by the headlamps
from following vehicles, low sun...
Manual day/night model
Adjustment
)
Adjust the mirror so that the glass is
directed correctly in the "day" position.
Day/night position
)
Pull the lever to change to the
"night" anti-dazzle position.
)
Push the lever to change to the
normal "day" position.
As a safety measure, the mirrors
should be adjusted to reduce the
"blind spot".
Page 70 of 340
III
68
COMFORT
As a safety precaution, these op-
erations must only be carried out
while the vehicle is stationary.
STEERING WHEEL ADJUSTMENT
The steering wheel can be adjusted
for height and reach to adapt the
driving position to the size of the
driver.
Adjustment
)
First, adjust the driver's seat to
the most suitable position.
)
When stationary
, pull the lever A
to unlock the steering wheel ad-
justment.
)
Adjust for height and reach.
)
Push the lever to lock the steering
wheel adjustment.
After locking, if you press fi rmly on
the steering wheel, a slight click may
be heard.
Automatic day/night model
In order to guarantee optimum visi-
bility during your manoeuvres, the
mirror lightens automatically when
reverse gear is engaged. By means of a sensor, which mea-
sures the light from the rear of the
vehicle, this system automatically
and progressively changes between
the day and night uses.
It has an anti-dazzle system which
darkens the mirror glass: this reduces
any driver discomfort caused by the
light beam of following vehicles, the
sun... In vehicles fi tted with electrochro-
matic door mirrors, the system has
an on/off button and an associated
warning lamp.
On
)
With the ignition on, press on
button 1
.
The warning lamp 2
comes on and the
mirror glass is in automatic mode.
Off
)
Press on button 1
.
The warning lamp 2
goes off and the
mirror glass remains in its lightest
defi nition.