Citroen C5 RHD 2012 (RD/TD) / 2.G Owner's Manual
Manufacturer: CITROEN, Model Year: 2012, Model line: C5 RHD, Model: Citroen C5 RHD 2012 (RD/TD) / 2.GPages: 340, PDF Size: 39.41 MB
Page 131 of 340
IX
!!
129
DRIVING
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operating modes:
- AUTOMATIC
Automatic application when the
engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the
parking brake is always possible
by pulling control lever A
while
pressing the brake pedal.
Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake is automatically applied
when the engine is switched off.
The application of the parking brake
is confi rmed by:
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by pulling
on control lever A
.
The application of the parking brake
is confi rmed by:
- warning lamp P
in the
control lever A
coming on,
Before leaving the vehicle,
check that warning lamp P
and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- display of a message "hand-
brake on" in the instrument panel
screen.
The noise of operation will confi rm
to you the application/release of
your electric parking brake.
- warning lamp P
in the
control lever A
coming on,
- display of a message "hand-
brake on" in the instrument panel
screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
-
this warning lamp in the in-
strument panel coming on,
- this warning lamp in the in-
strument panel coming on,
Page 132 of 340
IX!
!
130
DRIVING
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
)
with a manual gearbox
(fi rst
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accel-
erator pedal and move off.
)
with an automatic gearbox
, ac-
celerate with the selector in posi-
tion D
, M
or R
.
Full release of the parking brake is
confi rmed by:
- warning lamp P
in the
control lever A
going off,
- display of a message "hand-
brake off" in the instrument panel
screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake.
Do nat place any object (packet of
cigarettes, telephone...) between the
gear lever and the electric parking
brake control.
Activation/Deactivation of the
automatic functions
Depending on the country of sale,
automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
screen confi guration menu. Select
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
In some special circumstances,
with the engine not running,
(towing, icy conditions...) the au-
tomatic parking brake can be re-
leased manually, with the key in
the running position.
Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull
on control lever A
.
The application of the parking brake
is confi rmed by:
- warning lamp P
in the
control lever A
coming on,
- display of a message "hand-
brake on" in the instrument panel
screen.
When the driver’s door is opened
with the engine running, a mes-
sage is displayed accompanied
by an audible signal if the parking
brake has not been applied.
-
this warning lamp in the in-
strument panel coming on,
- this warning lamp in the
instrument panel going off,
If the confi guration menu does not
have the option to activate/deacti-
vate the automatic functions, this
can be done by a CITROËN dealer
or a qualifi ed workshop.
Page 133 of 340
IX
!
131
DRIVING
Release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal,
push then release
control lever A
.
The full application of the parking
brake is confi rmed by:
- warning lamp P
in the
control lever A
going off,
- display of a message "parking
brake released" in the instru-
ment panel screen.
If you push control lever A
without
pressing the brake pedal, the park-
ing brake will not be released and
the message "Apply foot on brake"
will be displayed on the instrument
panel.
When stationary, with the en-
gine running, do not press the
accelerator pedal unneces-
sarily, as you may release the
parking brake.
Maximum application
If necessary, you can utilise maxi-
mum application
of the parking
brake. It is obtained by means of a
long pull
on control lever A
, until
you see the message "Max applica-
tion of the handbrake" and a beep
is heard.
Maximum application is essential:
- in the case of a vehicle towing
a caravan or a trailer, if the au-
tomatic functions are activated
but you are applying the parking
brake manually,
- when the gradient you are parked
on is variable in its effect (e.g. on
a ferry, in a lorry, during towing).
- in the case of towing, a loaded
vehicle or parking on a gradient,
turn the front wheels towards the
pavement and engage a gear
when you park.
- after a maximum application, the
release time will be longer.
Particular situations
In certain situations (starting the en-
gine...), the parking brake can auto-
matically alter its level of application.
This is normal operation.
To advance your vehicle a few
centimetres without starting the en-
gine, but with the ignition on, press
on the brake pedal and release the
parking brake by pushing
then
releasing
control lever A
.
The full release of the parking brake
is confi rmed by the warning lamp P
in the control lever and the warning
lamp in the instrument panel going
off and the display of a message
"handbrake off" on the instrument
panel screen.
If the parking brake malfunctions
while applied
or if the battery is fl at,
an emergency release is still pos-
sible.
To ensure correct operation of the
parking brake and therefore your
safety, the number of successive
application/release operations is
limited to eight.
If this number is exceeded, you are
warned by the message "Parking
brake faulty" and a warning lamp
fl ashes.
- this warning lamp in the
instrument panel going off,
Page 134 of 340
IX
!
!
132
DRIVING
Dynamic emergency braking
In the event of a failure of the ve-
hicle’s main braking system or in
an exceptional situation (e.g. driver
taken ill, under instruction, etc) pull
and hold control lever A
to stop the
vehicle.
The electronic stability programme
(ESP) provides stability during dy-
namic emergency braking.
If there is a fault with the dynamic
emergency braking, one of the fol-
lowing messages will be displayed
in the instrument panel screen:
- "Parking brake faulty".
- "Parking brake control faulty". If a failure of the ESP system
is signalled by the lighting
of this warning lamp, then
braking stability is not guar-
anteed. In this event, stability must
be assured by the driver by repeat-
ing alternate "pull release" actions on
control lever A
.
The dynamic emergency
braking should only be used
in exceptional circumstances.
Emergency parking brake
release
In the event of the electric parking
brake failing to release, an emergency
device can be used to release the
parking brake manually, provided that
it is possible to immobilise the vehicle
while the procedure is carried out.
)
If you can start the vehicle: with
the engine running, immobilise
the vehicle by applying the foot
brake while the operation is being
carried out.
)
If you are unable to start the
vehicle (fl at battery for example):
do not use this device and contact
a CITROËN dealer or a qualifi ed
workshop. However, if you are
obliged to proceed, fi rst immobilise
your vehicle securely and then fol-
low the instructions below. If the vehicle cannot be im-
mobilised, do not operate
the emergency release. Your ve-
hicle may run away if on a slope.
Contact a CITROËN dealer or a
qualifi ed workshop.
Page 135 of 340
IX
!
133
DRIVING
)
On sloping ground: immobilise
the vehicle by placing the chocks
(if your vehicle has them) in front
or behind the two front wheels,
against the slope
On level ground: immobilise the
vehicle by placing the chocks
(if your vehicle has them) in
front and behind one of the front
wheels.
)
Open the lower compartment of
the centre armrest by pulling it.
)
Ensure that the cup holder B
is
folded away.
)
Remove the rubber mat covering
the base of the armrest.
This strap does not permit
application of the parking
brake.
To re-engage the electric parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A
until the park-
ing brake warning lamp (!) fl ashes
in the instrument panel then give a
second long pull until this warning
lamp is on fi xed.
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
brake has re-engaged (fl ashing of
the warning lamp (!) in the instru-
ment panel then the warning lamp
on fi xed) to avoid damage to the
parking brake.
Take care not to allow moisture or
dust in the proximity of the diagnos-
tic socket D
which is essential for
the maintenance of your vehicle.
)
Release the strap from its loca-
tion C
.
)
Pull the strap to release the
brake. A loud knock confi rms the
release of the brake.
)
Take care to put the strap back in
its location C
correctly. Otherwise,
it will no longer be possible to ap-
ply the brake. Contact a CITROËN
dealer or a qualifi ed workshop.
)
Put the rubber mat back in place
on the base of the armrest.
Page 136 of 340
IX
!
134
DRIVING
If any of these instances arises, contact a CITROËN dealer or a qualifi ed workshop as soon as possible.
SITUATION
CONSEQUENCES
1
Electric parking brake fault and display of
message " Parking brake faulty
" and the
following warning lamps: If the electric parking brake fault warning lamp and the service
warning lamp light up, position the vehicle in a safe location (on fl at
ground, with a gear engaged).
2
Display of the messages " Parking brake
faulty
" and " Anti roll-back
fault
" and of the
following warning lamps:
- The automatic functions are deactivated.
- The hill start assist is not available.
- The electric parking brake is only available manually.
3
Display of messages " Parking brake faulty
"
and " Anti roll-back
fault
" and of the following
warning lamp:
- Manual release of the electric parking brake is not available.
- The hill start assist is not available.
- The automatic functions and manual application are still
available.
Operating faults
Page 137 of 340
IX
135
DRIVING
SITUATION
CONSEQUENCES
4
Display of messages " Parking brake faulty
"
and " Anti roll-back
fault
" and of the following
warning lamps:
and/or
fl ashing
- The automatic functions are deactivated.
- The hill start assist is not available.
To apply the electric parking brake:
)
Immobilise the vehicle and switch off the ignition
)
Pull the control lever for at least 5 seconds or until maximum
application.
)
Switch on the ignition and check that the electric parking brake
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl ashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer or a qualifi ed workshop.
To release the electric parking brake:
)
Switch on the ignition.
)
Push the control lever and hold it for approximately 3 seconds.
5
Display of message " Parking brake control
faulty – automatic mode activated
" and the
following warning lamps:
and/or fl ashing
- Only the functions for automatic application on switching off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake and dynamic
emergency braking are unavailable.
6
Display of message " Parking brake faulty
"
and of the following warning lamp:
fl ashing
- Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
)
Wait approximately 3 minutes.
)
After 3 minutes, if the warning lamp is still fl ashing, try to
reinitialise the parking brake, either by pushing and releasing
the control A
while pressing the brake pedal or by means of a
long pull on control lever A
.
7
Battery fault
- Illumination of the battery warning lamp makes it essential to stop the
vehicle as soon as traffi c allows. Stop and immobilise your vehicle.
- Apply the electric parking brake before switching off the engine.
Page 138 of 340
IX!
136
DRIVING
HILL START ASSIST
System which keeps your vehicle
immobilised temporarily (approxi-
mately 2 seconds) when starting on
a gradient, the time to move your
foot from the brake pedal to the ac-
celerator pedal.
This function is only active when:
- the vehicle is completely stationary,
with your foot on the brake pedal,
- in certain conditions on a gradient,
- with the driver’s door closed.
The hill start assist function cannot
be deactivated.
Operation
On an ascending gradient, with
the vehicle stationary, the vehicle
is held for a brief moment when
you release the brake pedal:
- provided you are in fi rst gear or
neutral on a manual gearbox,
- provided you are in D
or M
on an
automatic gearbox.
On a descending gradient, with the
vehicle stationary and reverse gear
engaged, the vehicle is held for a
brief moment when you release the
brake pedal.
Do not exit the vehicle while
it is being held in the hill start
assist phase.
If you need to leave the vehicle with
the engine running, apply the park-
ing brake manually and ensure that
the parking brake warning lamp (in
the instrument panel) is on fi xed
(not fl ashing).
Page 139 of 340
IX
137
DRIVING
5-SPEED MANUAL GEARBOX
Starting the vehicle
)
Check that the gear lever is in
neutral.
)
Do not touch the accelerator.
)
For Diesel engines: turn the
key to position M
and wait until
the pre-heating warning lamp
switches off if it has come on.
)
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
)
In temperatures lower than 0°C,
declutch while operating the
starter to facilitate starting.
Engaging reverse gear
)
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL
GEARBOX
Engaging reverse gear
)
Raise the ring under the knob
(indicated by the arrow) and
push the gear lever to the left
then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
Page 140 of 340
IX
!
138
DRIVING
GEAR EFFICIENCY
INDICATOR *
System which reduces fuel con-
sumption by advising the driver to
change up on vehicles fi tted with a
manual gearbox.
Operation
The system intervenes only when
driving economically.
Depending on the driving situation
and your vehicle's equipment, the
system may advise you to skip one
or more gears. You can follow this
instruction without engaging the in-
termediate gears.
The gear engagement recommen-
dations must not be considered
compulsory. In fact, the confi gu-
ration of the road, the amount of
traffi c and safety remain determin-
ing factors when choosing the best
gear. Therefore, the driver remains
responsible for deciding whether or
not to follow the advice given by the
system.
This function cannot be deactivated.
* According to engine.
Example:
- You are in third gear.
- You press the accelerator pedal
moderately.
- The system may suggest that
you engage a higher gear, if ap-
propriate.
The information appears in the in-
strument panel screen in the form of
an arrow accompanied by the sug-
gested gear.
In the case of driving which
makes particular demands on
the performance of the engine
(fi rm pressure on the accelerator
pedal, for example, when overtak-
ing...), the system will not recom-
mend a gear change.
The system never suggests:
- engaging fi rst gear,
- engaging reverse gear,
- engaging a lower gear.