wheel CITROEN C6 2005 User Guide

Downloaded from www.Manualslib.com manuals search engine 58
ENGINE
CHECKING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1]Set of plugs: (-).0188-T
[2]Flywheel setting peg (double flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the battery negative terminal.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Remove:
- The air duct between the air/air exchanger and the air inlet housing (4).
- The air inlet housing (4).
Uncouple, plug and move aside the pipes (2)and (3), using tools [1].
Unclip and move aside the electrical harness.
Remove the venting chamber fixing (1).
Move aside the venting chamber (1).
B1BP3BXD
Angl-C6-page022-82-2005 4/02/05 17:19 Page 58

Downloaded from www.Manualslib.com manuals search engine 61
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: DT17BTED4
Tools.
[1] Kit of plugs: (-).0188-T
[2]Flywheel setting peg (double damping flywheel): (-).0195.K Toolkit 0188-T
[3]Camshaft setting pegs: (-).0195.H Toolkit 0188-T
[4]Belt compressure spring: (-).0188.K
[5]Coolant pump pulley peg: (-).0195.C
[6]Lifting bracket: (-).0195.N
IMPERATIVE: Respect the safety and cleanliness requirements.
WARNING: Before disconnectng the battery, partially open the door windows.
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel injection (HDi) engines.
Remove the engine cover.
Disconnect the negative terminal of the battery.
Raise and support the front of the vehicle.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield (see corresponding operation).
Angl-C6-page022-82-2005 4/02/05 17:19 Page 61

Downloaded from www.Manualslib.com manuals search engine 118
CLUTCH
GEARBOX
TRANSMISSION
CHECKING THE OIL PRESSURE IN THE AM6 AUTOMATIC GEARBOX
WARNING: Clean the flexible pipe of the tool [1] each time before use; the different
automatic gearbox oils cannot be intermixed.
Fit the tool [1]on the tool [2].
Perform the following operations:
- Raise the vehicle, wheels hanging.
- Apply the parking brake.
- Start the engine.
- Check the oil pressure.
WARNING: Wait for the gearbox oil to reach a temperature between 58°C and 68°C.
Check the level of oil in the gearbox (see corresponding operation).
NOTE:Check the temperature of the oil using the diagnostic tool in parameter measures.
Gear lever position: D.
Engine speed: Idling.
Principal oil pressure: 3.7 to 4.2 bars.
B1BP3END
Angl-C6-page101-120-2005 4/02/05 17:25 Page 118

Downloaded from www.Manualslib.com manuals search engine 120
CLUTCH
GEARBOX
TRANSMISSION
TRANSMISSION
Tightening torques (m.daN)Gearbox oil seal mandrels
Vehicle GearboxDriveshaft Driveshaft
Engines
bearing nutRight Left Tool kit
(-).0336.U (-).0336.V
C6 AM6 ES9A - DT17BTED4 2 ± 0,2 34,5 ± 2 8010-T
(-).0336.W (1)
(1) Guide for fitting driveshaft seal.
Tightening torques (m.daN) of the wheel bolts
CITROËNES9Al Steel
DT17BTED4 Alloy9 ± 1
Angl-C6-page101-120-2005 4/02/05 17:25 Page 120

Downloaded from www.Manualslib.com manuals search engine 121
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES
Engine plate
Tyre/circumference S
Type
WheelT
A
Name of rim
Normal operating pressure:
front/rear
Pressure for maximum load :
front/rear
Pressure: loaded, high speed:
front/rear
Tyre S
Spare wheel T
Normal operating pressure
Pressure for maximum load
Pressure: loaded, high speed 3.0i 24S 2,7 24V
XFV UHZ
225/55 R17 97W/2,071 m 245/45 R18 100W/2,065m 245/45 R18 100W/2,065m
Michelin PRIMACY
7 J17-CH5-32 8 J18-CH5-33 8 J18-CH5-33
SATURNE SAN MARIN 2 SAN MARIN 2
2,4/2,4 2,4/2,4 2,4/2,4
2,6/2,6 2,4/2,4 2,6/2,6
2,4/2,4 2,4/2,4 2,6/2,6
225/55 R17 97W
7 J17-5-32
2,6 2,4 2,6
2,6 2,4 2,6S =Standard fitting.T =Steel wheel.A=Alloy wheel.
NOTE:The label indicating the recommended tyre pressures is affixed to the front LH door pillar.
Angl-C6-page121-169-2005 4/02/05 17:31 Page 121

Downloaded from www.Manualslib.com manuals search engine 122
AXLES
SUSPENSION
STEERING
WHEEL AND TYRESNOTE:The label indicating the recommended tyre pressures is affixed to the front
LH door pillar.
«a»Recommended tyre inflation pressures (empty and under load)
«b»Tyre specifications
«c»Type of tyres
«d»Recommended inflation pressure for the spare wheel
B2GP01FD
Identification of inflation pressures
Angl-C6-page121-169-2005 4/02/05 17:31 Page 122

Downloaded from www.Manualslib.com manuals search engine 123
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES(1)Wheel bolt (all rim types)
(2)Light alloy wheel
(3)Steel aluminium wheel
NOTE:If mixed fixing bolts are fitted on steel wheels, the shoulders of the bolts
remain free.
Tightening torques for the wheel bolts.
9 ± 1 m.daN
B2GP00JD
Identification of the wheel bolts
Angl-C6-page121-169-2005 4/02/05 17:31 Page 123

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
124
WHEEL AND TYRES(4)Valve(8)Seal
(5)Antenna(9)Cap
(6)HF transmitter unit(10)Nut
(7)Washer
Composition.
A SIEMENS HFtransmitter module (6) integral to each wheel in the place of the
valve, each including a lithium battery.
An HFreceiver in the communication module under the dashboard.
WARNING: Each time a tyre is replaced, it is necessary to replace the valve (4).
WARNING: Each time a wheel rim is replaced, it is necessary to replace the
seal (8).
WARNING: Each time a transmitter module is changed, it is necessary to have
the replacement recognised by the deflation detection ECU, using a diagnostic
tool.
B2GP01ND
Deflation detection system
Angl-C6-page121-169-2005 4/02/05 17:31 Page 124

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
125
CHECKING AND ADJUSTING VEHICLE HEIGHT
IMPERATIVE: Respect the safety and cleanliness requirements.
Tools.
[1]Gauge for measuring radius of wheels (5 bolts): 9801-T
[2]Gauge for height under bodyshell: 2305-T
[3] LEXIAstation: 4171-T
[4] PROXIAstation: 4165-T
Preliminary operations.
Check the tyre pressures.
Place the vehicle on a 4 column lift.
Switch on the ignition.
Release the parking brake.
Put the vehicle in the high position.
Put the vehicle in the normal height position (driving height).
During:During the measuring, do not move the vehicle.
Reference heights: REFERENCE = Ignition switched on
Angl-C6-page121-169-2005 4/02/05 17:31 Page 125

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
126 Place the tool [1]on the wheel
fixing bolts.
Measure the wheel radiuses
using tool [2].
Measure, using tool [2].
The front LHheight H1M: Measure between the ground and zone Aunder the front subframe.
The front RHheight H2M: Measure between the ground and zone Bunder the front subframe.
CHECKING AND ADJUSTING VEHICLE HEIGHT
Warning: During measurement of reference heights: Do not switch off the ignition
Measuring the front heights
Measuring the front wheel radiusesB3CP0AQD
B3CP0ARD
B3CP0ASD
Reference heights: REFERENCE = Ignition switched on
Angl-C6-page121-169-2005 4/02/05 17:31 Page 126