Citroen CX 1982 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 6. Electric cooling fans :
- 16 dm2 (248 sq.in ) radiator ( CX 2000 except optional towing equipment ) ,......... 1
- 20 dm2 (310 sq.in ) radiator (CX 2000 and 2200 except optional towing
equipment, or torque converter, or air-conditioning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
- 20 dm2 (310 sq.in ) radiator ( CX 2200 with optional towing equipment or
torque converter ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
20 dm2 (310 sq.in ) radiator ( CX 2200 with air-conditioning) ,............................... 2
- 20 dm2 (310 sq.in) radiator ( CX Prestige) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- 20 dm2 (310 sq.in) radiator (CX 2400, except optional towing equipment
or torque converter, or air-conditioning ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
20 dm2 ( 310 sq .in ) radiator ( CX 2400 with optional towing equipment, or
torque converter, or air-conditioning ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- 23 dm2 (356.5 sq.in ) radiator, ( CX 2400 GTi except optional towing equipment ) 1
- 23 dm2 (356.5 sq.in) radiator, (CX 2400 and Prestige with optional torque
converter and air~conditioning, and CX 2400 Gti with optional towing
equipment ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 O-blade fan
5-blade fan
5-blade fans
lo-blade fans
1 O-blade fans
1 O-blade fan
1 O-blade fans
10 blade fan
lo-blade fans
The electric cooling fans are controlled by a thermal switch (011 /he
radiator)
e Power rating of electric fan : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W
Direction of rotation ( S(J(‘IJ ~YOIII
c>lcctric ~/o/or side of /alI ) : . . . . . Clockwise
- Cut-in thermal switch :
1.6 dm2 (248 sq.in ) 20 dm2 ( 310 sq.in ) and
radiator 23 dm2 (356.5 sq.in,) rads
- Electric fan ( s ) cuts in at . . 101 to
103.5” c, 95 to loo0 c
-. Electric fan ( s ) cuts out (with
trmperatnw decreasing )
at : ._._._._._........... 9 5 to 920 c 95 to 9o” c
- Tightening torque (fit gasket with LOCTITE FRENETANCH ) : 1.8 to 2 da Nm ( 13 to 14.5 ft.lbs)

Downloaded from www.Manualslib.com manuals search engine COOLING SYSTEM
L litre enlyne f
-I l’r’i ) except optional towing equipment (Thermostat closed and heater system open)
Hot cool.n+
>Id coolant I Electric fan
2 Radiator
3 De-aerating pipe
4 Header tank (expansion
chamber
5 Thermostat
2 6 Heater unit
7 Inlet manifold
8 Cvlinder head outlet tank
Partial view F
II Thermostot closed

Downloaded from www.Manualslib.com manuals search engine COOLING SYSTEM
/ 11’re e!!qlric
-1 1’1-5 j except oprlonal row,ng equ,pmenr
Thermostat and heater unit open
Hot coolant
Cold coolant I Electric fan
2 Rodiotor
3 De-aerating pipe
4 Header tank
5 Thermostot
6 Heater unit
2 7 Inlet manifold
8 Cylinder heod outlet tonL
-3
Portia1 view F
Thermostat open

Downloaded from www.Manualslib.com manuals search engine -
-
‘F
L
Radiator
! Electric fan ( 5)
I De-oeroting pipe
I Header tank
i Thermostot
I Heater unit
Inlet manifold
i Cylinder head outlet tank Thermostat closed
Hot coolant
Cold coolont -

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 230.00 : ( i ‘ 1 Radiator 2
Electric fan ( s )
3 De-oerot~ng pipe 4
Header tank
5 Thermostat 6
Heater unit
7 Inlet manifold
8 Cylinder-heod outlet tank
8 -‘I KY - -
Partial-view F - Partial view F
6
Thermostat open

Downloaded from www.Manualslib.com manuals search engine COOLING SYSTEM
2 4 litre engine, torque converter and air conditinninq (Thermostat and heater unit open)
Partial view F
8
1 Radiator
2 Electric fon (5)
3 De-aerating pipe
4 Header tank
5 De-aeration chamber
6 Thermostat
7 Heater unit
8 Drain top
9 Cylinder head outlet tank Cold coolant
,
I-
J1
- 0 Thermal switch for electric fan (s)
l-J 7
6
Thermostat open

Downloaded from www.Manualslib.com manuals search engine OPERATION NJ MA. 230.00 : 1 i !O,Oi ,V,iC,i< c “ii<, ‘/QC < iOi ,< “,,i!< 0, ii’< /
Op. MA. 230.00 7
COOLING SYSTEM
2 4 litre engine fuel injection (Thermostat and heater unit open)
Hat coolant
Cold coolant
Partial view F
1 Rodiotor
2 Electric fon (5)
3 De-aerating pipe
4 Header tank
5 De-aeration chamber
6 Thermostat
7 Heater unit
6 Drain top
9 Thermal switch for fan
0 Bleed screws
Thermast.t open

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 230.0 : M k
08 ,ri,y r,i, //I<’ roo/i,ip c, s,w,,.
Op. MA. 230.0 1 FILLING THE WATER SYSTEM
IMPORTANT
: Core must be token to protect alternator from water whenever working on cooling systems fitted close to this unit.
Two operations are involved
- Complete filling i roolir~g c~s~<,v, nvd bvolvr ,,ail ,
- Partial filling I roolir,p ~J~S/IW, oul~* 1
NOTES
Draining the radiator and the engine unit does not involve draining the heater unit.
- De-aeration of the system is only operative when the thermostat is open 1 v,rgiur wnnu J.
I. COMPLETE REFILLING 1. Remove
spare wheel
.
2. Open heater control to fullest extent ( inside
vehicle 1.
3. Unscrew the two bleed screws ( 1 ) and ( 2 ).
Place a tronsporent tube
200 mm in length
over each screw in order to ovoid the escape
of the liquid.
4. Disconnect the heater outlet hose and pour in
approximately 0.6 litre of cooling liquid.
Reconnect tube ( 4).
5. Fill remainder of circuit slowly through the
header tank and close bleed screws I 1) and
( 2) after releasing air
6. Remove transparent tubes ( 3) and close header
tank.
NOTE : To induce primitzg o/pum~,~~~sseri;irrp
o/ circuit I I bar 1 f 14. 5 psi ) may b+ r~i/vrtd:
(11 through overflow orifice ( 5)
I Vehicles -2/ 1976 ).

Downloaded from www.Manualslib.com manuals search engine 2 OPERATION No MA. 230-O : II .h’ 0, fug Ol, I/7‘, rodir,p sys/w1.
b) by replacing the header tank cap with a
flexible rocker-cover union
I V~~/7id<~S 2/ IU7h - ,
7. Run engine at approximately 2000 rpm until
electric fan (5) cut (5) in.
Then let the engine idle for about 10 mins.
Never open header tank cap while electric fan (5)
ore/is in operation.
Do not open bleed-screws ( 1 ) and (2) while engine
is running.
8. After releasing the air. water level should
stabilize in header tank. Level should be checked
when the engine is cold.
9. Fit the rubber covers cm the bleed-screws.
Replace spare wheel.
II. PARTIAL FILLING
Same operations as for total filling except that
the heater unit is not filled by outlet tube ( 3)
to the radiator.
111. FILLING AND DE-AERATING THE AUXILIARY
HEATER UNIT ON CX AMBULANCE VEHICLES
Before connecting the auxiliary heater unit water
system to the main system. the following must
be carried out :
- Fill up the auxiliary heater unit and its hoses
( with heater control open I with 1.6 litres
( 2.8 pts 1 of coolant liquid of the some type
as that used in the main
system.
- Connect all hoses. and tiqhten 011 hose clips.
-Stat engine. and wait for electric fan (5) to
to cut-in ( De-aeration time 1.’
- Check the operation of the auxilioly heater unit.
- WHEN THE ENGINE IS COLD, check the level,
and top up if necessary.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 236.0 : C h<,rki,,p a,,d nd;r,slh,p I/w jwllr\s aurl /x,//s Op. MA. 2360 I
PULLEY ALIGN& IENT
1. Aligning the camshaft pulley :
a) Position device 3085-T on the water pump
pulley.
b) Bring its rod into contact with the groove of the
camshaft pulley.
NOTE Aligning the camshaft pulley is carried
out by’plocing shims behind the pulley.
Tightening torque for nut (2) for the comshoft
pulley : 8 daNm ( 58 h.lb ).
2. Aligning the alternator pulley :
Proceed as for camshaft pulley / ,,,;/I> s SC-r<,!, , j I /or I,,<, RllI~)11010F c<)L,, <,d i,, ,,
NOTE Aligning the alternator pulley is carried
out by plocinq shims behind the pulley.
Tightening torque for nut (4) for the olternatov
pulley : 4 daNm ( 29 ft.lb ).
3. Aligning the high pressure pump :
a ) Tighten pump on its support plate
b) Place device 3085-T on the camshaft pulley.
c) Brinq its rod into contact with the groove of the
pump pulley.
NOTE Aliqninq the H P pump is curried out using
adjustment shims placed between the pump housing
and the support plate.
Tightening torque for the nut securing the H.P. pump :
4 doNm ( 29 ft.lb ).
NOTE Vchirlc,s filled ,,~;//I oirrrii,rli/iriniii,~
For the alignment of the compressor pulley, SLO
Opr~mrio~, MA, ~,40.,-(,.