light CITROEN DISPATCH SPACETOURER DAG 2018 Handbook (in English)

250
Brake disc wear
For information on checking brake
disc wear, contact a CITROËN
dealer or a qualified workshop.
Only use products recommended by
CITROËN or products of equivalent quality
and specification.
In order to optimise the operation of units
as important as those in the braking
system, CITROËN selects and offers very
specific products.
After washing the vehicle, dampness, or
in wintry conditions, ice can form on the
brake discs and pads: braking efficiency
may be reduced. Make light brake
applications to dry and defrost the brakes.
AdBlue® (BlueHDi
engines)System SCR
By using a fluid called AdBlue® containing
urea, a catalytic converter turns up to 85%
of nitrogen oxides (NOx) into nitrogen and
water, which are harmless to health and the
environment.
The AdBlue
® is contained in
a special tank holding about
22


litres.
Its capacity allows a driving range of around
6,000-9,000


miles (10,000-15,000

km). An
alert system is triggered automatically when
the remaining range reaches 1,500


miles
(2,400

km), i.e. once the reser ve level has been
reached.
Several alerts are triggered successively during
the remaining 1,500

miles (2,400 km) before
the tank is empty.
If the estimated distance travelled by your
vehicle between two ser vices is greater than
12,000

miles (20,000

km), it will be necessary
to top up the AdBlue.
To respect the environment and ensure
compliance with the new Euro 6

standard,
without adversely affecting the performance or
fuel consumption of Diesel engines, CITROËN
has taken the decision to equip its vehicles
with a system that associates SCR (Selective
Catalytic Reduction) with a particle filter (DPF)
for the treatment of exhaust gases.
Practical information

252
Never top up from an AdBlue® dispenser
reserved for heavy goods vehicles.
Recommendations on storage
AdBlue® freezes below around -11°C and
deteriorates above 25°C. It is recommended
that bottles or containers be stored in a cool
place and protected from direct sunlight.
Under these conditions, the fluid can be kept
for at least a year.
If the additive has frozen, it can be used once it
has completely thawed out. Never store bottles or containers of
AdBlue
® in your vehicle.
In winter, check that the temperature
of the vehicle is above -11°C. If not, in
freezing weather, the AdBlue
® cannot be
poured into the tank. Park your vehicle
somewhere warmer for a few hours before
topping up.
Procedure
The supply in a non-drip container or bottle
simplifies topping up. Containers are available
from a CITROËN dealer or a qualified
workshop.
In cold weather, before per forming the top-up
ensure that the temperature of the vehicle is
above -11°C. Other wise the AdBlue
® may be
frozen and so cannot be poured into its tank.
Park your vehicle in a warmer area for a few
hours to allow the top-up to be carried out.
F

B

efore topping up, ensure that the vehicle is
parked on a flat and level sur face.
F

S

witch off the ignition to stop the engine
and remove the key from the switch.
or
F

W

ith

K

eyless Entry and Starting, press the
" START/STOP " button to stop the engine. F

F
or access to the AdBlue
® tank, open the
left front door.
F

F

rom below, pull the black cover.
F

T

urn the blue cap a 6th of a turn anti-
clockwise.
F

L

ift off the cap.
Practical information

256
Other engines
F Fill the fuel tank with at least five litres of Diesel.
F

O
pen the bonnet.
F

I
f necessary, unclip the cover to access the
priming pump.
F

O
perate the priming pump repeatedly until
resistance is felt (there may be resistance at
the first press).
F

O
perate the starter to start the engine
(if the engine does not start at the first
attempt, wait around 15
seconds before
trying again).
F

I
f the engine does not start after a few
attempts, operate the priming pump again
then start the engine.
F

P
ut the cover in place and clip it in.
F

C
lose the bonnet.
Tool box
Access
The tool box is located under the left-hand front
seat.As a safety measure, bars 1
and 2 prevent
the box escaping from its housing, if it is
not correctly secured.
Removing
F Press latches A and slide them inwards to release the box.
F

L
ift the box slightly then pull it as far as it will
go to take it past bar 1 .
F

T
hen, lift the box upwards to take it past
bar 2 .
In the event of a breakdown

257
Opening
Storage
F Refit the cover on the box and clip fixings B.
F
P
osition the box with the front inclined
upwards.
F

T
o take it past bar 2 , push the box in and
down. F

T
o take it past bar 1
, raise the box slightly
then push it fully in.
F
O
nce the box is fully home
in its housing,
push it against the floor carpet then slide
latches A outwards to secure it.
Pull on the box to check that it is secure in
its housing.
With a temporary puncture
repair kit
F Unclip fixings B on the cover, then open it for access to the tools.
1.12
V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also
be used for adjusting tyre pressures.
2. Towing eye.
8
In the event of a breakdown

262
Removing the pipe and
cartridge
Be careful of fluid discharge.
The expiry date of the fluid is indicated on
the cartridge.
The sealant cartridge is designed for
single use; it must be replaced even if only
partly used.
After use, do not discard the cartridge into
the environment, take it to an authorised
waste disposal site or a CITROËN dealer.
Do not forget to obtain a new sealant
cartridge, available from CITROËN
dealers or from a qualified workshop.
Checking/adjusting tyre
pressures
F Turn pipe assembly 2 to the left until it
contacts the unit.
F

D
isconnect the connector 1 from the
cartridge by turning it a quarter turn anti-
clockwise.
F

P
ull pipe assembly 2 out slightly, then
disconnect connector 3
from the air intake
pipe by turning it a quarter turn anti-
clockwise. F

R
emove pipe assembly 2
.
F
K
eep the compressor vertical.
F
U
nscrew the cartridge 4 from the bottom.
To fit the new cartridge and new pipe, carry out
these operations in reverse order.
F

T
urn selector A to the "air"
position.
F

U
ncoil the white pipe G fully.
F

C
onnect the pipe to the tyre
valve.
You can also use the compressor, without
injecting sealant, to check and if necessary
adjust the tyre pressures .
In the event of a breakdown

270
Ty p e E
When each operation has been completed,
check the operation of the lighting.
Front lamps
Halogen headlamps
Xenon bulb: xenon bulbs must be changed by
a CITROËN dealer or a qualified workshop as
there is a risk of electrocution.For more information on Changing a bulb

and in particular the types of bulb, refer to the
corresponding section.
For H7 type bulbs with lugs, take care to
obser ve their correct installation so as to
ensure the best lighting performance.
1.
Sidelamps.
Ty p e A , W5W-5W
2. Main beam headlamps.
Ty p e C , H1- 55W
3. Dipped beam headlamps.
Ty p e C , H7- 5 5 W
4. Daytime running lamps.
Ty p e A , W21W LL-21W
5. Direction indicators.
Ty p e B , PY21W-21W (amber)
Xenon headlamps
For more information on Changing a bulb
and in particular the types of bulb, refer to the
corresponding section.
1. Main beam headlamps.
Ty p e C , H1- 55W
2. Dipped beam headlamps.
Ty p e E , D8S 25W
3. Direction indicators.
Ty p e B , PY21W-21W (amber)
In the event of a breakdown

271
Foglamps
Ty p e D, H11 - 5 5 W
Daytime running lamps/sidelamps
If fitted to your vehicle, contact a CITROËN
dealer or a qualified workshop for the
replacement of this type of LED lamp and light
guide.
A replacement kit for the LEDs is available from
CITROËN dealers.
Direction indicator side repeater
Ty p e A , W Y5W-5W (amber)
-
P
ush the repeater towards the rear and
disengage it.
-
W

hen refitting, engage the repeater towards
the front and then bring it towards the rear.
Amber coloured bulbs (direction indicators and
side repeaters) must be replaced with bulbs of
identical specification and colour.
Dipped beam headlamps
(halogen headlamps)
Ty p e C , H7- 5 5 W
When refitting the connector and bulb
in the lamp, push the assembly into its
housing until it clicks into place.
F

P
ress the upper clip on the cover then tip it
rear wards to remove it.
F

P
ress the lower clip on the electrical
connector and remove the assembly of
connector and bulb.
F

P
ull the bulb out and change it.
To refit, proceed in reverse order.
8
In the event of a breakdown

275
1.Brake lamps/sidelamps.
Ty p e B , P21/5W-21/5W
2. Direction indicators.
Ty p e B , PY21W-21W (amber)
3. Reversing lamps.
Ty p e B , P21W-21W
4. Foglamps/sidelamps.
Ty p e B , P21/4W-21/4W
For vehicles with interior trim, contact a
CITROËN dealer or a qualified workshop
to have the work done. F

I
dentify the failed bulb then open the rear
doors.
F
F
rom inside, remove the air vent, if your
vehicle has one.
F
F
rom outside, unscrew the two fixing
screws.
F
W
hile holding the lamp in place, press the
clip located on the inside then carefully
remove the lamp.
F

D
isconnect the electrical connector.F

S
pread the 3 lugs slightly, then extract the
bulb holder.
F
R
emove the failed bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F
R
eplace the bulb.
To refit, proceed in reverse order.
Rear lamps (side-hinged
rear doors)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
8
In the event of a breakdown

277
1.Brake lamps/sidelamps.
Ty p e B , P21/5W-21/5W
2. Direction indicators.
Ty p e B , PY21W-21W (amber)
3. Reversing lamps.
Ty p e B , P21W-21W
4. Foglamps/sidelamps.
Ty p e B , P21/4W-21/4W
For vehicles with interior trim, contact a
CITROËN dealer or a qualified workshop
to have the work done. F

I
dentify the defective bulb then open the
tailgate.
F
F
rom inside, remove the cover, if your
vehicle has one.
F
F
rom the outside, press the interior clips
of the plastic trim then tilt it outwards to
remove it.
F

U
nscrew the two lamp fixing screws.F

W
hile holding the lamp in place, press the
clip located on the inside then carefully
remove the lamp.
F
D
isconnect the electrical connector.
F
S
pread the 3 lugs slightly, then extract the
bulb holder.
Rear lamps (tailgate)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
8
In the event of a breakdown

278
To refit, proceed in reverse order.
Third brake lamp (tailgate)
Ty p e A, W5W-5W
F
O
pen the tailgate.
F

R
emove the failed bulb by pressing
lightly on it, then turning it a quarter turn
clockwise.
F
R
eplace the bulb.
F
U
nclip the trim at each end by turning it
upwards.
F P ull the trim to unclip the centre clips, then
remove it.
F

U
sing a screwdriver through the aperture,
push the lamp towards the outside.
F

D
isconnect the electrical connector.
F

R
emove the lamp.
F

T
urn the bulb holder a quarter turn anti-
clockwise.
F

C
hange the faulty bulb.
To refit, proceed in reverse order.
To refit the lamp and trim, press on them to clip
them in place.
Number plate lamps (tailgate)
Ty p e A , W5W-5W
F
I
nsert a thin screwdriver into one of the cut-
outs in the lens.
F

P
ush it outwards to unclip it.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place.
In the event of a breakdown