ignition CITROEN DS3 CABRIO DAG 2015 Handbook (in English)

DS3_en_Chap03_ouvertures_ed01-2014
Following disconnection of the vehicle battery, replacement   of   the   remote   control   battery   or  
i

n   the   event   of   a   remote   control   malfunction,  
y

ou   can   no   longer   unlock,   lock   or   locate  
y

our vehicle.
F
 
F
irst   of   all,   use   the   key   in   the   lock   to   unlock  
o

r   lock   your   vehicle.
F
 
T
hen,   reinitialise   the   remote   control.
If
  the   problem   persists,   contact   a   CITROËN  
d

ealer   as   soon   as   possible.
Remote control problem
Reinitialisation
F Switch  off   the   ignition.
F  T urn   the   key   to   position   2 (Ignition).
F
 
P
ress   the   closed   padlock   immediately   for   a  
f

ew   seconds.
F
 
S
witch   off   the   ignition   and   remove   the   key  
f

rom   the   ignition   switch.
The
  remote   control   is   fully   operational   again.
changing the battery
Battery ref.: CR1620 / 3 volts.F  U nclip   the   casing   by   inserting   a   coin   at   the  
n

otch   and   rotating.
F
 
S
lide   the   flat   battery   out   of   its   location.
F

S
lide the new battery into its location
observing
  the   original   direction.
F
 
C
lip   the   casing   in   place,   then   the   chrome  
f

inisher.
F
 
R
einitialise   the   remote   control.
If the battery is flat, you are
informed
  by   lighting   of   this   warning  
l

amp   in   the   instrument   panel,   an   audible   signal  
a

nd   a   message   in   the   multifunction   screen.
F
 
U
nfold   the   key.
F
 
R
elease   the   chrome   finisher   by   pressing  
on
  lug   A.
F
 
M
aintain   pressure   on   lug   A   and   remove   the  
c

hrome   finisher   by   sliding   it   off   at   45°.

65
DS3_en_Chap03_ouvertures_ed01-2014
Do not throw the remote control batteries   away,   they   contain   metals  
w

hich   are   harmful   to   the   environment.
Take
  them   to   an   approved   collection  
po

int.Lost keys
Go to a CITROËN dealer with the vehicle's registration document, your personal identification   documents   and   if   possible   the   key   code   label.
The
  CITROËN   dealer   will   be   able   to   look   up   the   key   code   and   the   transponder   code  
r

equired   to   order   a   new   key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket   as   there   is   a   possibility   that   it   may   unlock   the   vehicle,   without   you   being   aware   of   it.
Do
  not   repeatedly   press   the   buttons   of   your   remote   control   out   of   range   and   out   of   sight   of  
y

our   vehicle.   You   run   the   risk   of   stopping   it   from   working   and   the   remote   control   would   have  
t

o   be   reinitialised.
No
  remote   control   can   operate   when   the   key   is   in   the   ignition   switch,   even   when   the   ignition  
i

s   switched   off,   except   for   reinitialisation.
Locking the vehicle
Driving with the doors locked may make access to the passenger compartment by the emergency   services   more   difficult   in   an   emergency.
As
  a   safety   precaution,   never   leave   children   alone   in   the   vehicle,   except   for   a   very   short   period.
In
  all   cases,   it   is   essential   to   remove   the   key   from   the   ignition   switch   when   leaving  
t

he vehicle.
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could c ause m alfunctions.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a CITROËN dealer, to ensure   that   only   your   keys   can   be   used   to   open   and   start   the   vehicle.
Access

DS3_en_Chap03_ouvertures_ed01-2014
1. driver's electric window switch.
2. P
assenger's electric window switch.
Window controlsSystem which opens or closes a window manually or automatically. It is fitted with anti-pinch protection on the driver's side.
T he electric window switches
remain
  operational   for   approximately  
4

5 seconds   after   the   ignition   is  
s

witched   off   or   until   a   door   is   opened.
If,
  during   this   period   of   45   seconds,   you  
o

pen   a   door   while   operating   a   window,  
t

he   window   stops.   The   window   switch  
w

ill then only be operative after the
ignition
  is   switched   on   again. F
 
P
ress   or   pull   the   switch.   The  
w

indow stops as soon as the
switch
  is   released.
Passenger's electric
window
There are two methods of operation:
driver's electric window
- manual modeF  P ress   or   pull   the   switch   without   passing  
t

he   point   of   resistance.   The   window  
s

tops   as   soon   as   the   switch   is   released.
-

a
utomatic mode
F
 
P
ress  
o
r  
p
ull  
t
he  
s
witch  
f
ully.  
T
he  
w
indow  
o

pens   or   closes   completely   when   the  
s

witch   is   released.
F
 
P
ressing   or   pulling   the   switch   again  
s

tops   the   movement   of   the   window.

81
DS3_en_Chap04_confort_ed01-2014
Mirrors
Each fitted with an adjustable mirror glass permitting t he la teral r earward v ision n ecessary f

or   overtaking   or   parking.   They   can   also   be  
f

olded   for   parking   in   confined   spaces.
demisting - def rosting Adjustment
F Move control A
  to   the   right   or   to   the   left   to  s
elect   the   corresponding   mirror.
F

M
ove control B in all four directions to
adjust.
F

R
eturn control A   to   the   central   position.
door mirrors
The objects observed are, in reality, closer   than   they   appear.
Take
  this   into   account   in   order   to  
c

orrectly   judge   the   distance   of   vehicles  
a

pproaching   from   behind.
Folding
F From  outside:   lock   the   vehicle   using   the  r
emote   control   or   the   key.
F
 
F
rom   inside:   with   the   ignition   on,   pull   the  
c

ontrol A   in   the   central   position   rear wards.
Unfolding
F From  outside:   unlock   the   vehicle   using   the  r
emote   control   or   the   key.
F
 
F
rom   inside:   with   the   ignition   on,   pull   the  
c

ontrol A   in   the   central   position   rear wards.
If
 
t
he  
m
irrors  
a
re  
f
olded  
u
sing  
c
ontrol 
A,
they will not unfold when the vehicle is
unlocked.   Pull   again   on   control   A
.
The   folding   and   unfolding   of   the   door  
m

irrors   using   the   remote   control   can   be  
d

eactivated by a CITR
oË
N dealer or a
qualified
 w

orkshop.
Never
  fold   or   unfold   the   electric   folding  
m

irrors
 m
anually.
If your vehicle is fitted with heated
mirrors,
 
the
 
demisting-defrosting
 
o

perates
 
with
 
the
 
engine
 
running,
 
by
 
s

witching
 
on
 
the
 
heated
 
rear
 
screen
 
(

refer
 
to
 
the
 
"Rear
 
screen
 
demist-defrost"
 
pag

e).
comfort

99
DS3_en_Chap05_amenagement_ed01
Component which protects against sunlight from  t he  f ront  o r  t he  s ide,  a lso  e quipped  w ith  a n  
i

lluminated
 v
anity
 m
irror.
F
 
W
ith   the   ignition   on,   raise   the   concealing  
f

lap;   the   mirror   is   lit   automatically.
This
  sun   visor   is   also   equipped   with   a   ticket  
h

o l d e r.
Sun visor Illuminated g love 
b

ox
This can be used to hold a water bottle.
I ts   lid   has   a   location   for   storing   the   vehicle's  
han

dbook
 pa
ck.
F
 
T
o   open   the   glove   box,   raise   the   handle.
It
  is   lit   when   the   lid   is   opened.
It
  houses   the   front   passenger's   airbag  
d

eactivation switch A .
It provides access to the ventilation nozzle B ,
distributing
  the   same   air   as   the   vents   in   the  
p

assenger
 c
ompartment.
Centre armrest
Storage
F For  access   to   the   closed   storage   box,   lift  t
he   lever   to   open   the   lid.
F
 
F
or   access   to   the   open   storage   box   below  
t

he   armrest,   lift   the   complete   armrest  
t

owards   the   rear.
These
  can   be   used   for   portable   devices   (mobile  
p

hone,   MP3   player...)   which   can   be   connected  
t

o   the   USB   port   /   auxiliary   socket   or   charged  
f

rom   the   12   V   socket   in   the   centre   console.
Comfort
  and   storage   system   for   the   driver   and  
f

ront
 p
assenger.
Fittings

DS3_en_Chap06_conduite_ed01-2014
Operating fault
With the ignition on, if this warning lamp   comes   on   and   AUTO flashes,
accompanied
  by   an   audible   signal   and   a  
m

essage
 
in
  the   multifunction   screen,   this  
i

ndicates
 
a
 
gearbox   fault.
Have
 
it
 
checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w

orkshop.
Reinitialisation
(5-speed electronic
gearbox)
In exceptional circumstances, the g earbox   may   need   an   automatic  
r

einitialisation:   starting   and   gear  
c

hanging   are   no   longer   possible.
AUTO and - - appear in the
instrument
 pan

el.
AUTO and - -   appear   in   the   instrument   panel.
F Select position N.
F  P ress   the   brake   pedal.
F

W
ait for around 30 seconds until N or a
gear
  appears   in   the   instrument   panel.
F
 
M
ove   the   gear   lever   to   position   A, then to
position N .
F
 
W
ith   your   foot   still   on   the   brake   pedal,   start  
t

he
 eng
ine.
The
  gearbox   is   operational   again.
Following
  disconnection   of   the   battery,   it   is  
n

ecessary   to   reinitialise   the   gearbox.
F  
S
witch   on   the   ignition.
Follow   the   procedure   described   above.

DS3_en_Chap06_conduite_ed01-2014
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
g

ear   lever   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   gear   lever   in
 t

he N
 

position   and   apply   the   parking   brake.
If the lever is not in position P
,
when the driver's door is opened or
approximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the lever to position P ;
 
the
 
m

essage
 d

isappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from   N to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact a CITR
oË

N dealer or a qualified
workshop
 
as   soon   as   possible.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
four
 
gears.
F

P

ush the lever towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the lever towards the -
 
sign
 
to
 
change
 
d

own
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or N 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to
 i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

DS3_en_Chap06_conduite_ed01-2014
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
Going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "E
cO
" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
you
 
p

ress
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
lever
 
i

n position N .
A
 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 d

uring
 
a
 
journey.
 
It
 
rests
 
itself
 t

o
 
zero
 
every
 
time
 
the
 
ignition
 
is
 s

witched
 
on
 
with
 
the
 
key. STOP
  mode   is   not   invoked   when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(10
  km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "EcO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

DS3_en_Chap06_conduite_ed01-2014
The system is reactivated automatically at   every   new   start   using   the   key.
Reactivation
This system requires a battery with a special specification   and   technology   (reference  
n

umbers   available   from   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop).
Fitting
  a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
In
 
the
 
event
 
of
 
a
 
fault
 
with
 
the
 
system,
 
the
 
"

E
cO O

FF"
 
switch
 
warning
 
lamp
 
flashes
 
then
 
c

omes
 
on
 
continuously.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
the
 
v

ehicle
 
may
 
stall.
 
All
 
of
 
the
 
instrument
 
panel
 
w

arning
 
lamps
 
come
 
on.
 
It
 
is
 
then
 
necessary
 
t

o
 
switch
 
off
 
the
 
ignition
 
and
 
start
 
the
 
engine
 
a

gain
 
using
 
the
 
key.
Operating fault Maintenance
Before doing anything under the b
onnet, deactivate the Stop & Start
system
  to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
The
  Stop   &   Start   system   makes   use  
o

f   advanced   technology.   All   work  
o

n   this   type   of   battery   must   be   done  
b

y a CITR
oË
N dealer or a qualified
workshop.
Press the "EcO O
FF"
 
switch
 
again.
The
 
system
 
is
 
active
 
again;
 
this
 
is
 
confirmed
 
b

y
 
the
 
switch
 
warning
 
lamp
 
going
 
off,
 
a

ccompanied
 
by
 
a
 
message
 
in
 
the
 
screen.

DS3_en_Chap06_conduite_ed01-2014
System which prevents the vehicle from exceeding   the   speed   programmed   by   the  
d

river.
When
  the   programmed   speed   limit   is   reached,  
p

ressing   the   accelerator   pedal   in   the   normal  
m

anner   no   longer   has   any   effect.
The
  speed   limiter   is   switched on
 m
anually:
 it r

equires   a   programmed   speed   of   at   least  
20
  mph   (30   km/h).
The
  speed   limiter   is   switched off
 
by   manual  
o

peration   of   the   control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly.
To
  return   to   the   programmed   speed,   simply  
s

low   down   to   a   speed   below   the   programmed  
s

peed.
The
 
p
rogrammed  
s
peed  
r
emains  
i
n  
t
he  
m
emory  
w

hen   the   ignition   is   switched   off.
Speed limiter
The speed limiter cannot, in any circumstances, replace   the   need   to   respect   speed   limits,   nor   can   it r

eplace   the   need   for   vigilance   on   the   part   of   the   driver.
The controls of this system are grouped together   on   stalk   A.
1.
 S

peed   limiter   mode   selection   thumb   wheel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 S

peed   limiter   on   /   off   button.
Steering mounted controls
The programmed information is grouped together   in   the   instrument   panel   screen.
5.
 S

peed   limiter   on   /   off   indication.
6.
 S

peed   limiter   mode   selection   indication.
7.
 P

rogrammed   speed   value.
displays in the instrument panel