Citroen DS3 RHD 2015 1.G Owner's Guide
Manufacturer: CITROEN, Model Year: 2015, Model line: DS3 RHD, Model: Citroen DS3 RHD 2015 1.GPages: 387, PDF Size: 12.26 MB
Page 31 of 387

29
Warning/indicator lampis on Cause Action / Observations
Engine
autodiagnosis
system flashing.
The
 engine  management  system  has Â
a
 fault.Risk
 of  destruction  of  the  catalytic  converter.
Have
 it  checked  by  a  CITROËN  dealer  or  a  qualified Â
w
orkshop.
fixed. The
 emission  control  system  has  a Â
f
ault.
The warning lamp should go off when the engine is started.
I f  it  does  not  go  off,  contact  a  CITROËN  dealer  or  qualified w
orkshop  without  delay.
Low fuel level fixed. When  it  first  comes  on  there  remains  a
pproximately 5 litres of fuel in the
tank. You
 must  refuel  as  soon  as  possible  to  avoid  running o
ut  of  fuel.
This
 warning  lamp  will  come  on  every  time  the  ignition  is
 s
witched  on,  until  a  sufficient  addition  of  fuel  is  made.
Fuel
 tank  capacity:  approximately  50  litres  (petrol),
Â
4
6  litres  (Diesel)  or  33  litres  (LPG);  depending  on
 v
ersion:  approximately  30  litres  (petrol  or  Diesel).
Never
 continue  to  drive  until  you  run  out  of  fuel  as
 t
his  could  damage  the  emission  control  and  injection
 s
ystems.
Maximum coolant
temperature fixed.
The
Â
t
emperature Â
o
f Â
t
he Â
c
ooling Â
s
ystem Â
i
s  too  high.Stop
 as  soon  as  it  is  safe  to  do  so.
Wait
 until  the  engine  has  cooled  down  before  topping Â
u
p  the  level,  if  necessary.
If
 the  problem  persists,  contact  a  CITROËN  dealer  or Â
q
ualified
 w
orkshop.
Monitoring
Page 32 of 387

Warning/indicator lampis on Cause Action / Observations
Engine oil
pressure fixed.
There
 is  a  fault  with  the  engine Â
l
ubrication  system.You
 must  stop  as  soon  it  is  safe  to  do  so.
Park,
 switch  off  the  ignition  and  contact  a  CITROËN Â
d
ealer  or  a  qualified  workshop.
Battery charge fixed. The
 battery  charging  circuit  has  a  fault Â
(
dirty  or  loose  terminals,  slack  or  cut Â
a
lternator  belt,  ...).The
 warning  lamp  should  go  off  when  the  engine  is Â
s
tarted.
If
 it  does  not  go  off,  contact  a  CITROËN  dealer  or  a Â
q
ualified
 w
orkshop.
d
oor(s) open fixed
 if  the  speed  is Â
b
elow  6  mph  (10  km/h).A
 door  or  the  boot  is  still  open. Close  the  door  or  boot.
fixed
 and  accompanied Â
b
y  an  audible  signal  if Â
t
he  speed  is  above Â
6
 mph  (10  km/h).
Page 33 of 387

31
Airbagstemporarily. This  lamp  comes  on  for  a  few  seconds  w
hen  you  turn  on  the  ignition,  then Â
g
oes  off.This
 lamp  should  go  off  when  the  engine  is  started.
If  it  does  not  go  off,  contact  a  CITROËN  dealer  or  a Â
q
ualified
 w
orkshop.
fixed. One
 of  the  airbag  or  seat  belt Â
p
retensioner  systems  has  a  fault.Have
 it  checked  by  a  CITROËN  dealer  or  a  qualified Â
w
orkshop.
Warning
/indicator lampis on Cause Action / Observations
Seat belt not
fastened /
unfastened fixed
 then  flashing Â
a
ccompanied  by  an Â
inc
reasing
 a
udible
 s
ignal. The
 driver  and/or  the  front  passenger Â
h
as  not  fastened  or  has  unfastened Â
t
heir  seat  belt.Pull
 the  strap  then  insert  the  tongue  in  the  buckle.
Power steering fixed. The
 power  steering  has  a  fault. Drive  carefully  at  reduced  speed.
Have
 it  checked  by  a  CITROËN  dealer  or  a  qualified Â
w
orkshop.
Monitoring
Page 34 of 387

Warning/indicator lampis on Cause Action / Observations
Under-inflation fixed,
 accompanied  by Â
a
n  audible  signal  and  a Â
m
essage.The
 pressure  in  one  or  more  tyres  is Â
t
oo  low.Check
 the  tyre  pressures  as  soon  as  possible.
This
 check  should  preferably  be  carried  out  when  the Â
t
yres  are  cold.
You
 must  reinitialise  the  system  after  the  adjustment  of Â
o
ne  or  more  tyre  pressures  and  after  changing  one  or Â
m
ore  wheels.
For
 more  information,  refer  to  the  "Under-inflation Â
d
etection"
 s
ection.
+ flashing
 then  fixed, Â
a
ccompanied  by  the Â
S
ervice  warning  lamp.The
 system  has  fault:  the  tyre Â
p
ressures  are  no  longer  monitored.Check
 the  tyre  pressures  as  soon  as  possible.
Have
 the  system  checked  by  a  CITROËN  dealer  or  a Â
q
ualified
 w
orkshop.
Page 35 of 387

33
Warning/indicator lampis on Cause Action / Observations
AdBlue
® additive
(BlueH
d i d iesel) fixed,
 on  switching  o
n  the  ignition, Â
a
ccompanied  by  an Â
a
udible  signal  and  a Â
m
essage  indicating Â
t
he
 r
emaining
 d
riving
 ra
nge. The
 remaining  driving  range  is  b
etween  350  miles  (600  km)  and Â
1
500 miles  (2400  km).Have
 the  AdBlue® additive tank topped up as soon a
s
Â
possible:
Â
go
Â
to
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop,
Â
or
Â
carry  out  this  operation  yourself  by Â
r
eferring
Â
to
Â
the
Â
corresponding  section.
+ flashing
 a
ssociated
 w
ith
 t
he
Â
SERVICE
Â
warning
 l
amp,
Â
accompanied
Â
by
 a
n
Â
audible
Â
signal
Â
and
 a
Â
message
Â
indicating
 t
he
 r
emaining
 d
riving
 ra
nge. The
Â
remaining
Â
driving
Â
range
Â
is
Â
b
etween
Â
0
Â
and
Â
350
Â
miles
Â
(600
Â
km). You
Â
must
Â
top-up the Â
Ad
Blue
® additive tank to avoid
a
breakdown :
Â
go
Â
to
Â
a
Â
CITROËN  dealer  or  a  qualified Â
w
orkshop,
Â
or
Â
carry
Â
out
Â
this
Â
operation  yourself  by Â
r
eferring
Â
to
Â
the
Â
corresponding
 section.
flashing,
Â
associated
Â
w
ith the SERVICE
warning
 lam
p,
 a
ccompanied
Â
by
Â
an
Â
a
udible
Â
signal
Â
and
Â
a
Â
m
essage
Â
indicating
Â
t
hat
Â
starting
Â
is
Â
p
revented. The
Â
AdBlue
® tank is empty: the s
tarting
Â
inhibition  system  required Â
b
y
Â
legislation  prevents  starting  of  the Â
e
ngine. To
 be  able  to  start  the  engine,  you  must  top-up the
AdBlue® additive tank: go to a CITROËN dealer or a q
ualified  workshop,  or  carry  out  this  operation  yourself Â
b
y
Â
referring  to  the  corresponding  section.
It is essential
Â
to  add  at  least  3.8  litres  of  AdBlue
® to
the
Â
additive
Â
tank.
Monitoring
Page 36 of 387

Warning/indicator lampis on Cause Action / Observations
+
+ SCR emissions
control system
(BlueH
d i d iesel)fixed,
 on  switching  on  the Â
i
gnition,  associated  with Â
t
he  SERVICE  and  engine Â
d
iagnostic  warning  lamps, Â
a
ccompanied  by  an  audible Â
s
ignal  and  a  message.A
 fault  with  the  SCR  emissions  control Â
s
ystem  has  been  detected.This
 alert  disappears  once  the  exhaust Â
e
missions  return  to  normal  levels.
flashing,
 on  switching  on Â
t
he  ignition,  associated  with Â
t
he  SERVICE  and  engine Â
d
iagnostic  warning  lamps, Â
a
ccompanied  by  an  audible Â
s
ignal  and  a  message Â
i
ndicating
 t
he
 r
emaining
 d
riving
 ra
nge. After
 confirmation  of  the  fault  with  the Â
e
missions  control  system,  you  can Â
d
rive  for  up  to  650  miles  (1  100  km) Â
b
efore  the  engine  starting  inhibition Â
s
ystem  is  triggered.Contact
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop  without delay, to avoid a
breakdown .
flashing,
 on  switching  on Â
t
he  ignition,  associated  with Â
t
he  SERVICE  and  engine Â
d
iagnostic  warning  lamps, Â
a
ccompanied  by  an  audible Â
s
ignal  and  a  message.You
 have  exceeded  the  authorised Â
d
riving  limit  following  confirmation Â
o
f  a  fault  with  the  emissions  control Â
s
ystem:  the  engine  starting  inhibition Â
s
ystem  prevents  starting  of  the Â
e
ngine.To
 be  able  to  start  the  engine,  you  must call
on
 a  CITROËN  dealer  or  a  qualified  workshop.
Page 37 of 387

35
With the engine running, when the needle is:
-  i n  zone  A,
 the  temperature  is  correct,
-
Â
i
n  zone  B,  the  temperature  is  too  high; Â
t
he central STOP
Â
warning  lamp  and  the Â
m
aximum  temperature  warning  lamp 1
come
 on  in  red,  accompanied  by  an Â
a
udible  signal  and  a  message  in  the Â
m
ultifunction
 s
creen.
You must stop as soon as it is safe to do so.
Wait
 a  few  minutes  before  switching  off  the Â
e
ngine.
Contact
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop.
Coolant temperature indicator
After driving for a few minutes, the temperature and  pressure  in  the  cooling  system  increase.
To
 top  up  the  level:
F
Â
w
ait  for  the  engine  to  cool  down,
F
u
nscrew the cap by two turns to allow the
pressure
 to  drop,
F
Â
w
hen  the  pressure  has  dropped,  remove Â
t
he cap,
F
Â
t
op  up  the  level  to  the  "MA X"  mark.
Monitoring
Page 38 of 387

System which informs the driver when the next  service  is  due,  in  accordance  with  the Â
ma
nufacturer's
 ser
vicing
 s
chedule.
Service indicator
Between 600 miles (1 000 km)
and 1 800 miles (3 000 km) remain
before the next service is due
For 5 seconds after the ignition is switched on, the  spanner  symbolising  the  service  operations Â
c
omes  on.  The  distance  recorder  display  line Â
i
ndicates  the  distance  remaining  before  the Â
n
ext  service  is  due.
Example:
Â
1  739  miles  (2  800  km)  remain Â
b
efore  the  next  service  is  due.
For
 5  seconds  after  the  ignition  is  switched  on, Â
t
he  screen  indicates:
5
 seconds  after  the  ignition  is  switched  on, Â
t
he spanner goes off ;
 the  distance  recorder Â
r
esumes  its  normal  operation.  The  screen  then Â
i
ndicates  the  total  distance.
For
Â
BlueHDi
Â
Diesel
Â
versions,
Â
the
Â
d
egree
Â
of
Â
deterioration
Â
of
Â
the
Â
engine
Â
oil
Â
i
s
Â
also
Â
taken
Â
into
Â
account
Â
(depending
Â
o
n
Â
the
Â
country
Â
of
Â
sale).
The
Â
point
Â
at
Â
which
Â
the
Â
next
Â
service
Â
is
Â
due
Â
is
Â
c
alculated
Â
from
Â
the
Â
last
Â
indicator
Â
zero
Â
reset,
Â
d
epending
Â
on
Â
the
Â
distance
Â
travelled
Â
and
Â
the
Â
t
ime
Â
elapsed
Â
since
Â
the
Â
last
Â
service.
More than 1 800 miles (3 000 km)
remain before the next service is
due
When the ignition is switched on, no service i nformation  appears  in  the  screen.
Page 39 of 387

37
Less than 600 miles (1 000 km)
remain before the next service is due
Example: 560  miles  (900  km)  remain  before  t
he  next  service  is  due.
For
 5  seconds  after  the  ignition  is  switched  on, Â
t
he  screen  indicates:
5
 seconds  after  the  ignition  is  switched  on, Â
t
he  distance  recorder  resumes  its  normal Â
ope
ration.
 T
he spanner remains on to
indicate
 that  a  service  must  be  carried  out Â
s
oon. 5
 seconds  after  the  ignition  is  switched  on, Â
t
he  distance  recorder  resumes  its  normal Â
ope
ration.
 T
he spanner remains on.
Service overdue
For 5 seconds after the ignition is switched on, the
s panner flashes to  indicate  that  the  service  must b
e  carried  out  as  soon  as  possible.
Example:
Â
the  service  is  overdue  by  180  miles
Â
(
300 Â km).
For
 5  seconds  after  the  ignition  is  switched  on,  the
 s
creen  indicates: For
 BlueHDi  Diesel  versions,  this  alert  m
ay  also  be  accompanied  by  the  fixed Â
i
llumination  of  the  service  warning  lamp Â
w
hen  the  ignition  is  on.
The
 distance  remaining  may  be Â
w
eighted  by  the  time  factor,  depending Â
o
n  the  driving  conditions.
Therefore,
 the  spanner  may  also  come Â
o
n  if  you  have  exceeded  the  period Â
s
ince  the  last  service,  indicated  in  the Â
ma
nufacturer's
 ser
vice
 s
chedule.
For
 BlueHDi  Diesel  versions,  the Â
s
panner  may  also  be  brought  on  earlier Â
t
han  expected,  depending  on  the Â
d
egree  of  deterioration  of  the  engine  oil Â
(
depending  on  the  country  of  sale).
The
 rate  of  deterioration  of  the  engine Â
o
il  depends  on  the  driving  conditions  in Â
w
hich  the  vehicle  is  used.
Monitoring
Page 40 of 387

Service indicator zero reset
After each service, the service indicator must be  reset  to  zero.
The
 procedure  for  resetting  to  zero  is  as Â
f
ollows:
F
Â
s
witch  off  the  ignition,
F
Â
p
ress  and  hold  the  trip  distance  recorder Â
z
ero reset button,
F
Â
s
witch Â
o
n Â
t
he Â
i
gnition; Â
t
he Â
d
istance Â
r
ecorder Â
d
isplay  begins  a  countdown,
F
Â
w
hen  the  display  indicates  "=0", release
the
 button;  the  spanner  disappears. Following
 this  operation,  if  you  wish  to Â
d
isconnect  the  battery,  lock  the  vehicle Â
a
nd  wait  at  least  five  minutes  for  the Â
z
ero  reset  to  be  taken  into  account.
Retrieving the service
information
You can access the service information at any t
ime.
F
Â
P
ress  the  trip  distance  recorder  zero  reset Â
b
utton.
 T
he  service  information  is  displayed  for  a Â
f
ew  seconds,  then  disappears.