Citroen DS5 2014 1.G Manual PDF

69Access

Safety anti-pinch

When the window rises and meets an obstacle,
it stops and immediately partially lowers again.
In the event of unwanted opening of the
window on closing, press the switch until the
window opens completely, then pull the switch
immediately until the window closes. Continue
to hold the switch for approximately one second
after the window has closed.
The safety anti-pinch function is not active
during this operation.


Deactivating the rear window
controls

Reinitialisation of the
electric windows

In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When operating the passenger electric
window switches, the driver must
ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.
Be aware of passengers or other
persons present when closing the
windows using the the electronic key
or the "Keyless Entry and Starting"
system.
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch function is not active
during these operations:


- lower the window completely, then raise
it, it will rise in steps of a few centimetres
each time the switch is pressed. Repeat
the operation until the window closes
completely,

- continue to press the switch for at least
one second after reaching this position,
window closed.
For the safety of your children, press
switch 5
to prevent operation of the
rear windows irrespective of their
position.
The warning lamp in the button comes on,
accompanied by a message confirming
activation. It remains on, as long as the child
lock is activated.
The interior controls for the rear doors are also
deactivated.
Opening the doors from the outside and
operation of the rear electric windows from the
driver's controls remain possible.

Cockpit glass roof

A tinted glass panoramic sur face to increase
the light and visibility in the passenger
compartment.
Fitted with three electric blinds to improve
temperature and noise related comfort. There are two options for opening and closing:


Electric blinds





Pull or press control, going beyond the
point of resistance.
One press opens or closes the blind
completely.
After a new action on the the control, the
blind continues moving for around 2 cm,
then stops.




Pull or press the control without going
beyond the point of resistance (for wards to
close and rear wards to open).
When you release the control, the blind
continues moving for around 2 cm, then
stops.

71Access

Safety anti-pinch


If the blind stops and immediately opens again
during a closing manoeuvre:



operate the control until the blind is fully
open,


then operate the control until the blind is
fully closed.

The safety anti-pinch function is not
operational during these operations.


If the blind meets an obstacle during
operation, you must reverse the
movement of the blind. To do this, press
the control concerned.
When the driver operates the blind
control, they must ensure that no one is
preventing correct closing of the blind.
The driver must ensure that passengers
use the blind correctly.
Be aware of children when operating
the blind.



Reinitialisation

If power to the blind is cut off while it is moving,
the safety anti-pinch must be reinitialised:



operate the control until the blind is fully
closed,


continue to press for at least 3 seconds. A
slight movement of the blind will then be
noticeable, confirming the reinitialisation.
In automatic mode and at the end of its travel,
if the blind meets an obstacle while closing it
stops and moves back slightly.

Fuel tank

Capacity of the tank: approximately 60 litres

.

Additions of fuel must be of at least 5 litres to
be registered by the fuel gauge.
Opening the filler cap may result in an inrush of
air. This vacuum is entirely normal and results
from the sealing of the fuel system.



Take care to select the pump that delivers
the correct fuel type for your vehicle's
engine (reminder on a label on the inside of
the filler flap).


Open the filler cap by turning it a 1/4 turn to
the left.


Remove the filler cap and hang it on its
carrier (on the filler flap).

Opening


If you have put in the wrong fuel for
your vehicle, you must have have
the tank drained and refilled with
the correct fuel before you star t the
engine.








With Stop & Start, never refuel with the
system in STOP mode; you must switch
off the ignition with the START/STOP
button.


Refuelling



Introduce the nozzle and push it in fully
(pushing open the non-return valve A
on
petrol vehicles).


Fill the tank (don't continue past the third
cut-off of the nozzle, as this may cause
malfunctions).


Refit the filler cap turning it a 1/4 turn to the
right.


Push the filler flap to close it.

Your vehicle is fitted with a catalytic converter
which reduces harmful emissions in the
exhaust gas.
The filler neck is narrower and allows only
petrol nozzles to be used.

For a petrol engine, the use of unleaded fuel
is
compulsory.



Press the switch
This switch remains active for a few minutes
after switching off the ignition. If necessary,
switch the ignition on again to reactivate it.

73Access

Low fuel level


When the low fuel level in the
tank is reached, this warning lamp
comes on in the instrument panel,
accompanied by an audible warning
and a message in the instrument
panel screen.
When it first comes on, around 6 litres of fuel
remain in the tank.
Until sufficient fuel has been added, this
warning lamp appears every time the ignition
is switched on, accompanied by an audible
signal and a message. This audible signal
and message are repeated with increasing
frequency as the fuel level drops and
approaches "0".
You must refuel as soon as possible to avoid
running out.


Fuel supply cut- of f

Your vehicle is equipped with a safety device
which cuts off the fuel supply in the event of a
collision. It remains possible to use a fuel can to
fill the tank.
In order to ensure a good flow of fuel,
do not place the nozzle of the fuel can
in direct contact with the flap of the
misfuel prevention device and pour
slowly.
















Misfuel prevention (Diesel) *

Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of
engine damage that can result from filling with the wrong fuel.
Located in the filler neck, the misfuel prevention device appears when the filler cap is removed.
When a petrol filler nozzle is introduced into the
fuel filler neck of your Diesel vehicle, it comes
into contact with the flap. The system remains
closed and prevents filling.

Do not persist but introduce a Diesel type
filler nozzle.




Operation



Travelling abroad

As Diesel fuel pump nozzles may be different
in other countries, the presence of the misfuel
prevention device may make refuelling
impossible.
Before travelling abroad, we recommend that
you check with the CITROËN dealer network,
whether your vehicle is suitable for the fuel
pumps in the country in which you want to
travel.


*
According to country of sale.

DIESEL










Quality of the fuel used for
petrol engines

The petrol engines are per fectly compatible
with E10 or E24 type petrol biofuels (containing
10 % or 24 % ethanol), conforming to European
standards EN 228 and EN 15376.
E85 type fuels (containing up to 85 % ethanol)
are reserved exclusively for vehicles marketed
for the use of this type of fuel (BioFlex
vehicles). The quality of the ethanol must
comply with European standard EN 15293.
For Brazil only, special vehicles are marketed
to run on fuels containing up to 100 % ethanol
(E100 type).













Quality of the fuel used for
Diesel engines

The Diesel engines are per fectly compatible
with biofuels which conform to current and
future European standards (Diesel fuel
which complies with standard EN 590 mixed
with a biofuel which complies with standard
EN 14214) available at the pumps (containing
up to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in certain Diesel
engines; however, this use is subject to strict
application of the special ser vicing conditions.
Contact a CITROËN dealer or a qualified
workshop.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or diluted,
domestic fuel...) is strictly prohibited (risk of
damage to the engine and fuel system).

75Access

003
Comfort

Front seats


Manual



1.
Adjustments to the height and angle
of
the head restraint

To raise it, pull upwards.
To lower it, press on the lug and the head
restraint at the same time.

2.
Adjustment of the backrest angle

Turn the wheel to adjust the angle of the
backrest.

3.
Adjustment of the seat height

Raise or lower the control lever the number
of times required to obtain the desired
position.

4.
For wards-backwards adjustment of the
seat position

Lift the control bar and slide the seat
for wards or backwards.

5.
Adjustment of the driver's lumbar
support

Turn the wheel to obtain the desired level
of lumbar support.


Before moving the seat backwards, ensure that there is nothing that might prevent the full
travel of the seat, so as to avoid the risk of of jamming the seat caused by the presence of
objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement
immediately.