Citroen GRAND C4 PICASSO RHD 2017 2.G Owner's Manual

139
Automatic gearbox
This gearbox offers two driving modes.
- a utomated mode for automatic
management of the gears by the gearbox,
without any action on the part of the driver,
-

m
anual mode for sequential gear changing
by the driver using the steering mounted
paddles.
P.
Pa

rk.
-

I
mmobilisation of the vehicle, parking brake
applied or released.
-

S
tarting the engine.
R.
R

everse.
-

R
eversing, vehicle stationary and engine at
idle.
N.
N

eutral.
-

I
mmobilisation of the vehicle, parking brake
applied.
-

S
tarting the engine.
D.
A

utomatic operation.
M.
M

anual operation with sequential changing
of the six gears.Gear selector lever
To select position P , move the gear
selector to the highest position
(towards
R )

, then push it for wards and
then to the left.
Only engage it when the vehicle is at a
complete stop. In this position, the front
wheels are locked. Ensure that the gear
selector is correctly positioned.
To move the gear selector, switch on
the ignition or start the engine.
If the battery is not sufficiently charged,
it is not possible to move the gear
selector. To come out of position P , move the
gear selector to the right to the desired
position, while keeping your foot on the
brake pedal.
It is possible to change from one mode
to the other at any time.
With the automated mode, you can
temporarily take control of the gear
changes at any time.
4
Driving

140
+. Control paddle for changing up, to the right of the steering wheel.
F

P
ull the " +" paddle towards you to change up.
-.
C

ontrol paddle for changing down, to the
left of the steering wheel.
F

P
ull the " -" paddle towards you to change
down.
Steering mounted control paddles
The steering mounted control paddles
cannot be used to select neutral or to
select or come out of reverse. When you move the gear selector, the symbol
corresponding to its position is displayed in the
instrument panel.
P.
Pa

rk.
R.
R
everse.
N.
N
eutral.
D.
D
rive (automatic operation).
1 to 6. Gears engaged in manual operation.
-.
I
nvalid value in manual operation.
Displays in the instrument panelMoving off
F With your foot on the brake pedal, select
position P or N .
F

S
tart the engine.
If P is displayed in the instrument panel,
although the gear selector is in another
position, place the gear selector in
position P to be able to start the engine.
F

W
ith the engine running, press the brake
pedal.
F

S
elect automated mode (position D ),
manual mode (position M) or reverse
(position R ).
If you do not press the
brake pedal to come out of
position P , this warning lamp
If these conditions are not met, there
is an audible signal accompanied by a
message.
or symbol appears in the instrument
panel, accompanied by the message
"Place automatic gearbox in position
P",
flashing of P in the instrument panel
and an audible signal.
Driving

141
F Check that the symbol displayed in the instrument panel agrees with the position
of the selector.
F

P
rogressively release the brake pedal.
F

I
f the parking brake is released, the vehicle
moves off.
I

f the parking brake is applied and
automatic operation is activated, accelerate
away.
Never press the accelerator and brake
pedals at the same time. Braking and
acceleration should be done only with
the right foot. Pressing both pedals
together risks damaging the gearbox. If the brake does not release
automatically, check that the front doors
are correctly closed. Never leave children unsupervised in
the vehicle when the engine is running.
When carrying out a maintenance
operation with the engine running, apply
the parking brake and select position P
.Never select position P or R unless the
vehicle is at a complete stop with the
brake applied.
When you want to engage reverse,
to avoid jolts, do not accelerate
immediately after engaging R
.
Changing into position R is
accompanied by an audible signal. Never select position N when driving.
If position N
is engaged in error when
moving, allow the engine to idle, then
engage position D to accelerate.
When the engine is running at idle,
brakes released, if position R
, D or M is
selected, the vehicle will move even if
the accelerator is not pressed.
4
Driving

142
Invalid value in manual operationThis symbol is displayed if a gear is
not engaged correctly (gear selector
between two positions).
You can temporarily take control of gear
changes using the

"
+ " and " -" steering mounted
control paddles. If the engine speed allows, the
instruction to change gear is acted on.
This function allows you to anticipate certain
situations such as overtaking another vehicle or
approaching a bend.
After a few moments with no action on the
control paddles, the gearbox manages the
gears automatically again.
Temporary manual control of the
gears
Manual mode
D and the gear engaged are displayed in the
instrument panel.
The gearbox operates in auto-active
mode, without any action from the driver. It
continuously selects the most appropriate gear
according to the following conditions:
-

o
ptimisation of fuel consumption,
-

d
riving style,
-

r
elief of the road,
-

v
ehicle load.
Automated mode
F Select position D .
For maximum acceleration, without touching
the gear selector, press the accelerator fully
down (kick down). The gearbox changes down
automatically and maintains the gear selected
until the maximum engine speed is reached.
When braking, the gearbox changes down
automatically for more effective engine braking.
When you take your foot off the accelerator
pedal suddenly, the gearbox does not change
up, so as to improve safety. F
Sel ect position M.
F

U
se the "+" and " -" steering mounted
control paddles to change gear.
The gears engaged are displayed successively
in the instrument panel.
When stationary or at very low speed, the
gearbox automatically engages 1st g e a r.
In manual mode, it is not necessary to release
the accelerator pedal when changing gear.
The change from one gear to another is only
effected if the conditions of vehicle speed and
engine speed allow; other wise the automatic
laws of operation are imposed temporarily.
If the engine speed is too high or too low,
the display of the gear selected flashes for a
few seconds, then the new gear engaged is
displayed.
It is possible to change mode at any
time, by moving the gear selector
from
D to M or the other way round.
Driving

143
Before switching off the engine, you can
change to position P or N to be in neutral.
In either case, apply the parking brake to
immobilise the vehicle, unless it is programmed
in automatic mode.
If the lever is not in position P, on opening the
driver's door or approximately 45 seconds after
switching off the ignition there is an audible
signal and a message appears:
F

m
ove the gear selector to position P; the
audible signal stops and the message
disappears.
Operating fault
Whenever parking, you must apply the parking
brake to immobilise the vehicle, if automatic
operation has been deactivated.
Parking the vehicle
In all circumstances, ensure that the
gear selector is in position P before
leaving your vehicle. In the event of a fault with the
gearbox, the service warning lamp
comes on in the instrument panel,
accompanied by a message and an
audible signal.
In this case the gearbox goes into back-up
mode and stays in 3
rd gear. You may then feel
a noticeable jolt when going from P to R and
from

N to R . This jolt does not present any risk
to the gearbox.
Do not exceed 60 mph (100 km/h) while also
observing legal speed limits.
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a battery failure, use the
chock to immobilise the vehicle.
4
Driving

144
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one or more gears.
You can follow this instruction without going
through the intermediate gears.
Gear efficiency indicator
System which reduces fuel consumption by recommending the most suitable gear.The system adapts its gear change
recommendation according to the
driving conditions (gradient, load, etc.)
and the demands of the driver (power,
acceleration, braking, etc.).
The system never suggests:
-

e
ngaging first gear,
-
enga

ging reverse gear,
-
c

hanging down.
The information appears in the instrument
panel in the form of an arrow.
On vehicles with a manual gearbox, the arrow
may be accompanied by the recommended
g e a r.
The gear engagement recommendations
must not be considered compulsory.
This is because the confi
guration of the
road, traffic density and safety remain
important factors in the choice of the best
g e a r.
The gear efficiency indicator system does not
replace the need for vigilance on the part of the
driver. With an automatic gearbox, the system is only active in manual mode.
On BlueHDi Diesel 135 and 150 versions with
manual gearbox, in certain driving conditions
the system may suggest changing into neutral
so that the engine can go into standby (STOP
mode with Stop & Start). In this case, N is
displayed in the instrument panel. Example:
This function cannot be deactivated.
-

Y
ou are in third gear.
-

Y
ou press the accelerator pedal.
-

T
he system may suggest that you engage
a higher gear.
Driving

145
Stop & Start
The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, etc.). The engine
restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Operation
Going into engine STOP
mode
This indicator lamp comes on in the instrument
panel and the engine goes into standby
automatically.
-
W
ith a manual gearbox, at speeds below
12 mph (20 km/h), or vehicle stationary
(with PureTech 130, THP 165 and
BlueHDi
100, 115 and 120 versions), when
you place the gear lever in neutral, and you
release the clutch pedal,
-

Wi
th an automatic gearbox, with the
vehicle stationary, when you press the
brake pedal or place the gear selector lever
at position N .
If your vehicle is fitted with the system, a time
counter calculates the sum of the periods in
STOP mode during a journey. It resets itself to
zero every time the ignition is switched on with
the START/STOP button. Never refuel with the engine in STOP
mode; you must switch off the ignition
with the START/STOP button. For your comfort, during parking
manoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as
for example, braking, power steering...
Special cases: STOP mode not
available
STOP mode is not invoked when:
-
t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
the START/STOP button,
-

t
he electric parking brake is applied or
being applied,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is selected,
-

s
ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the
engine is needed for control of a system.
In this case, this indicator lamp flashes
for a few seconds then goes off.
This operation is perfectly normal.
Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
4
Driving

146
Going into engine START mode
This indicator lamp goes off and the
engine starts automatically.
-

W

ith a manual gearbox , when you fully
depress the clutch pedal.
-

W

ith an automatic gearbox :
●

g

ear selector in position D or M , when
you release the brake pedal,
●

o

r gear selector in position N and brake
pedal released, when you place the gear
selector at position D or M ,
●

o

r when you engage reverse. START mode is invoked automatically when:
-
y ou open the driver's door,
-

y
ou unfasten the driver's seat belt,
-

t
he speed of the vehicle exceeds 16 mph
(25 km/h) with a manual gearbox (2 mph
(3 km/h) with PureTech 130, THP 165 and
BlueHDi 100, 115 and 120 versions) and
2
mph (3 km/h) with an automatic gearbox,
-

t
he electric parking brake is being applied,
-

s
ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the
engine is needed for control of a system.
Special cases: START invoked
automaticallyIn some circumstances, such as the need to
maintain a comfortable temperature in the
passenger compartment, it may be necessary
to deactivate the Stop & Start system.
The system can be deactivated at any time,
once the ignition is on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is automatically
reactivated every time the ignition is switched on.
Manual deactivation/
reactivation
In this case this indicator lamp flashes
for a few seconds, then goes off.
This operation is perfectly normal. Select "Stop & Start" to deactivate the system.
This is confirmed by the illumination
of this indicator lamp.
Using the dynamic cruise control
deactivates the Stop & Start system.
Deactivation of Stop & Start is done in the
Driving
menu of the touch screen.
Select "Stop & Start" again to reactivate the
system. This is confirmed by the illumination
of this indicator lamp.
Driving

147
Operating fault
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a fault in STOP mode, the vehicle
may stall.
All of the instrument panel warning lamps come on.
Depending on version, an alert message may also
be displayed, asking you to place the gear selector
lever at position N and put your foot on the brake
pedal.
It is then necessary to switch off the ignition and
start the engine again using the "START/STOP"
button.
In the event of a fault with the system,
this indicator lamp flashes for a few
moments then comes on continuously,
accompanied by a message.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid the risk of injury related
to an automatic change to START
mode.
Driving on flooded roads
Before driving through a flooded road,
it is strongly recommended that you
deactivate the Stop & Start system.
For more information on Driving
advice
, particularly on flooded roads,
refer to the corresponding section. The Stop & Start system requires a
battery of advanced technology and
special characteristics.
All work on this type of battery must
only be done by a CITROËN dealer or a
qualified workshop.
For more information on the 12 V
battery
, refer to the corresponding
section.
4
Driving

148
Memorising speeds
Memorising
This function allows speeds to be saved, which can then be offered to set the two systems: the speed limiter (to limit the speed of the vehicle) or the
cruise control (for a vehicle cruising speed).
You can memorise up to six speed settings for each of the two systems. By default, some speed settings are already memorised.F

S
elect the system for which you want to
memorise new speed settings.
This function is accessible in the Driving
menu
of the touch screen.
F

Sel
ect the " Driving function " tab, then
" Speed settings ".
F

P
ress the button corresponding to the
speed setting you want to modify.
As a safety measure, the driver must
carry out these operations when
stationary.
F

E
nter the new value using the numerical
keypad and confirm.
Driving