check engine Citroen JUMPER 2016 2.G Owner's Guide

140
jumper_en_Chap07_Verifications_ed01-2015
refilling / topping-up the
AdBlue® additive
Precautions to take
Use only AdBlue® additive that meets the
i

S
o
22241 standard.
The AdBlue
® additive is an urea-based
solution.
This liquid is non-flammable, colourless and
odourless.
To be kept in a cool area.
c

ontainers (5 or 10 litres) and
bottles

(1.89 litres) of AdBlue
®
Please check the use-by date.
r
ead the instructions on the label.
Ensure that you have a suitable filler pipe,
which may or may not be supplied with the
container. Park the vehicle
-

Before topping-up, ensure that the

vehicle is parked on a flat and level
surface.
Open the filler
- o pen the fuel filler flap.
-
T
urn the blue cap a 6
th of a turn anti-
clockwise.
-
r
emove the blue cap downwards.
top-up
-
o btain a bottle of AdBlue
®. After first
checking the use-by date, read carefully
the instructions on use on the label
before pouring the contents of the bottle
into your vehicle's AdBlue
® tank.
Important: if your vehicle's AdBlue
®
tank is completely empty - which is
confirmed by the alert messages and the
impossibility of starting the engine, you
must add at least 3.8 litres (so two 1.89 litre
bottles).
-

After emptying the bottle, wipe away any

spillage around the tank filler using a
damp cloth.
i

f any additive is split or splashed,
wash immediately with cold water or
wipe with a damp cloth.
i

f the additive has crystallised, clean it off
using a sponge and hot water.
AdBlue® additive

142
jumper_en_Chap08_Aide-rapide_ed01-2015
A. Positive metal point on your vehicle
B.
Slave battery
c

.
Earth on your vehicle
Make connections only to the points


indicated and illustrated above. Failure
to observe this instruction introduces
the risk of short-circuit!Starting from another battery
B
A
tt

E
r
Y
c
harging the battery using
a charger
- Connect the red cable to the metal
point
A then to the positive (+) terminal


of the slave battery B .
-

Connect one end of the green or black

cable to the negative (-) terminal of the
slave battery B .
-

Connect the other end of the green or

black cable to the earth point
c
on your

vehicle.
-
o perate the starter, let the engine run.
-

W
ait for the engine to return to idle, then
disconnect the cables. -
Go to the battery located in the front left
floor.
-

Disconnect the battery
.
-

Follow the instructions for use given by

the battery charger manufacturer.
-
r econnect starting with the negative (-)
terminal.
-

Check that the terminals and connectors

are clean.
i f they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
Discharged battery

143
jumper_en_Chap08_Aide-rapide_ed01-2015
Access to the battery
Unscrew the 6 access cover retaining
screws.
Lift off or remove completely the access
cover.
Press lever 1 downwards to spread the
clamp.
r

emove the terminal 2 from the negative (-)
post. The batteries contain harmful
substances such as sulphuric acid and
lead. They must be discarded in accordance
with the provisions of the law and must not,
in any circumstances, be discarded with
household waste.
Take used batteries to a special collection
point.
The charging operation must be carried
out in a ventilated area away from
naked flames or any possible sources of
sparks to eliminate the risk of explosion and
fire.
Do not attempt to charge a frozen battery: it
must first be thawed to eliminate the risks of
explosion.
i
f the battery has frozen, before
charging it have it checked by a specialist
who will check that the internal components
have not been damaged and that the
container is not cracked, which could mean
that there is a risk of a leak of toxic and
corrosive acid.
Proceed with a slow charge charge at low
current for a maximum pf about 24 hours to
avoid damaging the battery. Before disconnecting the battery, you must
wait for 2 minutes after switching off the
ignition.
n

ever disconnect a terminal when the
engine is running.
n
ever charge a battery without first
disconnecting the terminals.
Close the windows and doors before
disconnecting the battery.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems to be initialised.
i f slight difficulties
are experienced after this, please contact a
C
i T roën dealer or a qualified workshop.
Discharged battery
QUiCK HELP
8

146
jumper_en_Chap08_Aide-rapide_ed01-2015
FusesA (amps) Allocation
12 7.5
r

ight-hand dipped headlamp
13 7.5Left-hand dipped headlamp
31 5Engine compartment control unit relay - Dashboard control unit relay (i\
gnition switch +)
32 7.5Cabin lighting (battery +)
33 7.5Battery check sensor on Stop & Start version (battery +)
34 7.5Minibus interior lighting - Hazard warning lamps
36 10Audio system - Air conditioning controls - Alarm - Tachograph - Battery cut-off control unit - Additional
heating programmer (battery +)
37 7.5Brake lamp switch - Third brake lamp -
i nstrument panel (ignition +)
38 20Central door locking (battery +)
42 5ABS control unit and sensor - AS
r sensor - DSC sensor - Brake lamp switch
43 20Windscreen wiper motor (ignition switch +)
47 20Driver's electric window motor
48 20Passenger's electric window motor
49 5Parking sensors control unit - Audio system - Steering mounted controls - Centre and side switch panels\
-
Auxiliary switch panel - Battery cut-off control unit (ignition switch +)
50 7.5Airbags and pre-tensioners control unit
51 5Tachograph - Power steering control unit - Air conditioning -
r eversing lamps - Water in Diesel sensor -
Air
flow sensor (ignition switch +)
53 7.5
i

nstrument panel (battery +)
89 -
n

ot used
90 7.5Left-hand main beam
91 7.5
r

ight-hand main beam
92 7.5Left-hand front foglamp
93 7.5
r

ight-hand front foglamp
Failed fuse

148
jumper_en_Chap08_Aide-rapide_ed01-2015
Fuses in the engine
compartment
remove the nuts and tilt the box to access
the fuses.
r

efit the cover carefully after checking or
replacing fuses. Fuses
A (amps) Allocation
1 40ABS pump supply
2 50Diesel pre-heat unit
3 30
i
gnition switch - Starter motor
4 40Fuel heater
5 20/50Cabin ventilation with additional programmable heating
(battery +)
6 40/60Cabin fan maximum speed (battery +)
7 40/50/60 Cabin fan minimum speed (battery +)
8 40Cabin fan assembly (ignition switch +)
9 15
r
ear 12 V socket (battery +)
10 15Horn
11 -
n
ot used
14 15Front 12 V socket (battery +)
15 15Cigarette lighter (battery +)
16 -n
ot used
17 -
n

ot used
18 7.5Engine management control unit (battery +)
19 7.5Air conditioning compressor
20 30Screenwash/headlamp wash pump
21 15Fuel pump supply
22 -
n

ot used
23 30ABS electrovalves
24 7.5Auxiliary switch panel - Door mirror controls and folding
(ignition switch +)
30 15Door mirror heating
Failed fuse

161
jumper_en_Chap08_Aide-rapide_ed01-2015
PuncturE rEPAIr KItrepairing the tyre
- Apply the parking brake.
-
Unscrew the tyre valve cap, remove the

filling hose B and screw the ring E onto
the valve. -

Start the engine.
-
i nsert the connector G
into the nearest
power socket on the vehicle.
-

Switch on the compressor by placing the

switch F in position "I" (on),
-
i nflate the tyre to a pressure of 5 bar.
To obtain a more accurate reading, you are
advised to check the pressure value on the
pressure gauge H , with the compressor off.
-

Check that the switch
F on the
compressor is in position "0" (off).
This temporary puncture repair kit stowed
in a bag located in one of the front door
pockets.
It consists of:
-

a cartridge

A , containing the sealant
fluid, equipped with:
●

a filling hose

B ,
●

a sticker

c
indicating "max. 80 km/h",


which the driver must affix in full view
(on the dashboard) after repairing the
tyre,
-

a quick guide to use of the repair kit,
-


a compressor

d
equipped with a


pressure gauge and unions,
-

adaptors, for the inflation of various


items.
Puncture
QUiCK HELP
8

262
jumper_en_Chap11_Particularites_ed01-2015
WEIGHtS And tOWE d LOA d S ( KG )
For more information, refer to your registration certificate.
i

n each country, it is imperative that the towed loads authorised by
local legislation are complied with. To find out your vehicle's towing
capacities and its gross train weight, consult a franchised dealer.
The maximum authorised speed is reduced when towing (comply
with the legislation in force in your country).
With load transfer, the braked trailer weight can be increased,
on condition that the equivalent of this load is removed from the
vehicle so that the GTW is not exceeded. Warning: towing with a
lightly loaded towing vehicle may have an adverse effect on its road
holding.
The GTW and towed load values indicated are valid up to a
maximum altitude of 1000 metres; the towed load mentioned must
be reduced by 10 % for each additional 1000 metres.
High ambient temperatures may result in a reduction in the
performance of the vehicle in order to protect the engine; when the
ambient temperature is higher than 37 °C, limit the towed weight.
The kerb weight is equal to the weight without load + driver (75
kg) +
fuel tank filled to 90%. Before towing a trailer, check
that:
-

the nose weight on the

towbar ball does not exceed
the value (S) indicated on
the trailer's weights plate,
-

the maximum trailer weight

is less than the value
indicated on the trailer's
weights plate and the Gross
Vehicle Weight (GVW)
does not exceed the value
indicated on the vehicle's
weights plate.
-

in the case of a self-
supporting trailer

, the Gross
Train Weight must not
exceed the value indicated
on the vehicle's weights
plate.
General points
Tipper body