ESP Citroen XSARA 2005 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine 203
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Tools.
[1]Camshaft pinion peg: (-).0194.A
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Disconnect the battery.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel, the plastic pins holding the splash-shield, the splash-shield itself.
A:Pegging on the manualgearbox.
B:Pegging on the automaticgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
B1BP2V3D
B1BP38VC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 203

Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Peg the crankshaft, using tool [2].
Suspend the engine, using a workshop hoist.
Remove the RH engine support, the upper timing cover.
Peg the camshaft pulleys, using tool [1].
NOTE:The pegs [1]should go in without forcing.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and tensioning
the timing belt
(see corresponding operation).
Refitting.
Remove tools [1]and [2].
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B1BP2V3D
B1BP38VC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 204

Downloaded from www.Manualslib.com manuals search engine 205
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Tools.
[1] Camshaft setting peg: (-).0194.B
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-) 0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Hub immobilising tool: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189.S2
Pliers for removing plastic pins: 7504-T
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking and setting the timing.
Removing.
Disconnect the negative terminal of the battery
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove the auxiliaries drive belt
(see corresponding operation).
Unclip and move aside the fuel supply hose from the timing cover.
Suspend the engine by means of a workshop hoist.
Remove the RH engine support and the timing cover (1).
Turn the engine by means of the screw (3)of the crankshaft pinion (2)to bring it to the pegging
position.
B1BP310C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 205

Downloaded from www.Manualslib.com manuals search engine 209
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFJ
Tensioning the timing belt.
Refitting (continued).
Remove the tools[1] and[2].
Rotate the crankshaftten times
(normal direction of rotation).
IMPERATIVE: No exterior pressure or action should be applied on the timing belt.
Peg the inlet camshaft pulley, using tool[1].
Checking.
Timing belt tension.
IMPERATIVE: Check the position of the index «a», it should be opposite the slot «f». If the position of the index «a» is not correct, repeat
the operations to tension the timing belt.
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 209

Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING THE VALVE TIMING
Engine: RFN
Tools.
[1]Camshaft setting peg: (-).0189.A
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking the timing.
Removing.
Disconnect the battery negative terminal.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel, the splash-shield and the upper timing cover.
A:Pegging on the manualgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging
position.
Peg the crankshaft, using tool [2].
Unclip the fuel supply hose from the timing cover.
B1BP36QD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 210

Downloaded from www.Manualslib.com manuals search engine 211
ENGINE
211
CHECKING THE VALVE TIMING
Engine: RFN
Checking the timing (continued).
Suspend the engine, using a workshop hoist.
Remove the engine support (2)and the timing cover (1).
Peg the camshaft pulleys, using tool [1].
NOTE:The pegs [1]should go in without forcing.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and tensioning
the timing belt
(see corresponding operation).
Complete the refitting.
B1EP1GTC
B1EP1GUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 211

Downloaded from www.Manualslib.com manuals search engine 212
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFN
Tools.
[1] Camshaft setting peg: (-).0189.A
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-) 0189.K
[4] Adaptor for angular tightening: 4069-T
[5]Hub immobilising tool: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189.S2
Pliers for removing plastic pins: 7504-T
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking and setting the timing.
Removing.
Disconnect the negative terminal of the battery
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove the auxiliaries drive belt
(see corresponding operation).Unclip and move aside the fuel supply hose from the timing cover.
Remove the timing cover (1).
Turn the engine by means of the screw (3)of the crankshaft pinion (2)to bring it to the pegging
position.
B1BP2V4C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 212

Downloaded from www.Manualslib.com manuals search engine 216
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFN
Tensioning the timing belt.
Refitting (continued).
Remove the tools[1] and[2].
Rotate the crankshaftten times
(normal direction of rotation).
IMPERATIVE: No exterior pressure or action should be applied on the timing belt.
Peg the inlet camshaft pulley, using tool[1].
Checking.
Timing belt tension.
IMPERATIVE: Check the position of the index «a», it should be opposite the slot «g». If the position of the index «a» is not correct,
repeat the operations to tension the timig belt.
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 216

Downloaded from www.Manualslib.com manuals search engine 217
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Tools.
[1]Camshaft setting peg: (-) 0189.A
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-).0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Tool for moving and locking the tensioner roller: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189 S2
Pliers for removing plastic pins: 7504-T
Checking the setting of the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The upper timing cover.
C4AP12TC
XSARA - XSARA PICASSO
Engines: 6FZ - RFN
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 217

Downloaded from www.Manualslib.com manuals search engine 218
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Checking the setting of the timing (continued).
A:Pegging on the manualgearbox.
B:Pegging on the automaticgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
Peg the crankshaft, using tool [2].
Peg the camshaft pulleys, using tool [3].
NOTE:The pegs[3]should go in without effort.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and
tensioning the timing belt
(see corresponding operation).
Refitting.
Remove tools [2]and [3].
Complete the refitting in reverse order to removal.
B1BP2V3D
B1EP1BAC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 218