display DACIA SOLENZA 2004 User Guide

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 48
Diagnostic – General
A
If tester is displayin g:
“The after-sale code does
no t correspond to the pre-
sented key. Check if the
code was correctly en-
tered and if a vehicle key was presented
”.
If tester is displayin g:
“UCH programming fail-
ure. K ey not in use on
this vehicle”. The entered c ode does not
correspond to the vehicle’s key, the key does not belong to t hat vehicle or it is new.
The ke y code does not
correspond with t he e ntere d code
(the key belongs to other vehicle).
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 49
Diagnostic – General
THE PROCEDURE OF
KEYS ASSIGNATION
IMPORTANT : if not all keys are available it
will be necessary to subsequently perform the
assignation procedure with all the keys.
Enter in dialogue with syste m “Anti-
starting” .
In menu ”Control menu”, “Spe cifi c
c ontrol” , validate line “SC028: Key program-
ming”. Tester is displaying: “Take off the key from
anti-the ft contact”.
Tester is displaying “Enter the after-sale
code” .
With contact set off, enter the after-sale se-
cret code ( 12 hexadecimal characters) and vali-
date it. Tester is displaying “Attenti on. Not pre-
se nted k eys will be not active. Re -launch
th e procedure in order to re-assign them”:
the programming is under way. Tester is displaying: “Insert key in anti-
theft contact and set the contact on, then
validate” : set the contact on using a vehicle key
or a new key. Tester is displaying: “No of programmed
keys 1” and “ take off the key from anti-
theft contact, then validate” .
Tester is proposing: “Do you wish to pro-
gram a new key ?”. In order to assign additional keys, set the con-
tact on few seconds using the vehicle’s others
keys that must be assigned (maximum four), then
validate. Tester is displaying: “2, 3, 4 programmed
keys” and “ take off th e key from anti-theft
contact”. ATTE NT I ON: t h es e on es mus t be t he
vehicle ’s old keys or new not coded keys.
Tester is displaying: “ Data entry in me mory”,
Cockpit Central Unit is coded and the keys are
a ssigned.Th is message will be displayed for few
seconds, then you may come out from the re-
a ssignation procedure
ATTENTION : the maximum admissible
interval between each operation is of 5 min-
utes otherwise the procedure is canceled.
Tester is displaying in this situation the
me ssage: “Pe r for ming co nditions not
ac c ompli shed”. T hi s me ss age is also
d isplayed in case of dialogue loss with the
Cockp it C entral Unit or in case of battery
supplying cutting off.
SPECI AL SI TUATIONS
If te ster is displaying:
“Coc kpit Central Unit is empty. Launch
the C ockpit Centra l Un it p rogrammi ng
procedure”, th en the Cockpit Central Unit is
no t used. It is impossible to assign keys to a
not coded Cockp it Central Unit.
“Per forming conditions not accom-
pli s hed ”, t he entere d code is not correct;
check and then start ag ain the code entering
procedure.
If the key does corres pond to the Cockpit
Central Unit of that vehicle, the tester is dis-
playing “Interrupted procedure: attention,
the keys assigned to the vehicle are the
on es that have been assigned before pro-
cedure s tarting. T he pr es ented k eys be-
fore proc edure interruptio n are not any-
more empty and can be only assigned to
th is vehicle” assigned.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 50
Diagnostic – General
THE PROCEDURE OF KEYS’ ASSIGNATION
Enter in dialogue with thesystem “Anti-starting”
Select menu
“ Control module” and
“Specific c ontrol”.
V alidate line “SC 028:
Key programming”.
Tester is displaying: “
take off the key from
anti-theft contact”
T ester is displaying Enter
The after-sale code”.
Enter th e code (12
hexadecimal characters
with capitals) then validate it
A
The procedure must be performed
only when contact is set off.
If tester is displayin g:
“Cockpit Central Unit is
empty Launch the Cockpit
Central Unit programming
procedure”.
Tester is displaying
“ P erformi ng conditions
no t accomplished ”. Cockpit Central Unit is new.
It is impossible to assign the
keys to a Cockpit Ce ntral Unit not coded.
The entere d code is wrong or
it s not correct.
Check and re-e nter the c ode.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 51
Diagnostic – General
Te s t e r i s displaying: “At te nti o n.
The non presented keys shall be not
active. Re-launch the p rocedure in
order to re-assign them”.
T ester is displaying: “ Insert
k ey in anti-theft c ontact, set
contact on, then validate”.
Insert a key in anti-theft con-
tact. The key m ust be new or belonging to this vehicle. This procedure is enabling the
decommissionin g of one key in
case of its loss, for instance
T ester is displaying: 1 key
Pr ogrammed”, “Take off the
k ey from anti-theft contact,
then validate”.
Tester is displaying: “ Do you
wish to program another key?”
Insert another new key or
belonging to this vehicle in the anti-theft contact.
Tester is displaying: “ 2,3,4 keys
p rogrammed” then “T ake off the
k ey from t he anti-theft contact, then
validate”.
T ester is displaying: “ Data
entry in memory”.
The keys are assigned to the
vehicle. Check if the vehicle is starting and if the doors get
blocked by means of all keys If tester
is displayin g:
“Interrupted procedure: at- tention, the vehicle’s as-
s igned keys are those that
w ere assigned before the
procedure launching. The
keys presented before the
procedure interruption are
no t anymore empty and can
be assigned only to this ve-
hicle”.
The vehicle may use maximum 4 keys. The key does not
correspond to the
UCH of this vehicle
vnx.su

86
86 - 1
AUTO RA DIO
The au to radio may be fitted in the versions: radio-tapes player and radio with CD player.
RADIO-TAPES P LAYER PRESENTATION
1. On/off key
2. Key for tape fast-forwards up to next song
3. Tape eject key
4. Tape inserting door
5. Keys for tape forwards/backwards
6. Multi-purpose key (audio source selection, sound adjustment, radio frequency selection, and
traffic information
7. Display
8. Keys for radio programs memorizing (key 1 is used also for DOLBY function in tape listenin g)
9. Multi-purpose key (after selecting one function, the adjustments in the areas +, - or > , < are
performed)
CD PLAYER PRESENTATION
1. On/off key
2. CD eject key
3. CD insert door
4. Multi-purpose key (audio source selection, sound adjustment, radio frequency selection, and
traffic information
5. Display
6. Key for radio programs memorizing (key 1 is also used for CD listening)
7. Multi-purpose key (after selecting one function, the adjustments in the areas +, - or > , < are
performed)
General
vnx.su

86
86 - 2
AUTO RA DIO
MAIN FUNCTIONS
Function “ON / OFF Logic”
The radio may operate also when engine is stopped, when contact key is on “S” position. In
this situation, after 20 minutes of operation, an acoustic signal will be heard and the radio will
automatically stop. If you wish that radio is not stopping, after you heard the acoustic signal, push
the red starting key (1) that is enabling the radio operation for another 20 minutes.
If the contact key is brought on position “M” or “A” and the radio is started by pushing the
key (1), after the contact is set off, the radio will automatically stop. At next setting of the contact
on the position “M” or “A”, the radio will automatically start on the program set before starting.
Adjustment of the acoustic volume
By pushing the keys + or -, the acoustic volume may be adjusted, reaching its increasing or
decreasing. The acoustic volume level will be displayed in the moment of its adjustment and may
be from 0 (minim) to 30 9maxim).
Sound correction
This function is enabling the boosting or decreasing of the high /low frequencies, as well as the
balancing of the right/left and rear/front acoustic level.
RAD I O
The radio device is of multiple frequencies range, c omplex and is allowing the programs
selection in frequency range long waves (UL), medium waves (UM or ultra-short (FM).
RDS system ( Radio data System)
This system is enabling mute data transmitting , in the same time with a FM radio station signal.
The radio may use this system that is bringing the following advantages:
- emitter name displaying;
- information regarding others radio emitters;
- emergency messages;
- automatic reactivation.
Radio frequency selecti on
In order to perform this, push the key “SRC” many times so that the desired radio frequency
is selected.
General
vnx.su

86
86 - 3
AUTO RA DIO
Radio tuning on a transmitter
The ra dio receiver is using three selection m odes that may be seen on the scre en and a p-
proached on the radio front side: -manually ( TUNER MANU )
- by pre-selection (TUNER PRESEL)
- in alphabetical order (LIST)
Program memorizing
Af ter the desired waves range has been selected (UL, UM or FM) and the transmitter
reception is established, its memorizing may be performed, by pushing on of the yes from 1 to 6,
for at least two seconds, when an acoustic signal confirming the memorizing is to be heard.
Thermal protection
If the radio tempera ture is too hi gh for an optimal opera tion, the volume i s automatically
reduced ( without modification of the volume on the display ).
Code protection
The radio i s protected by m eans of a four-digit c ode. This code i s introduced by the ra dio
keys at each battery disconnection.
Code introduction by means of the radio keys : in order to valid one digit introduction,
push the next key (see the Operation technical book). In case of a wrong code, t he ra dio i s getting bl ocked (one minute for the first e rror, two
minutes for the second error, four minutes for the third…)
Af ter first code introduction, some confi gurations must be programmed (see chapter”
configuration”). These are remaining programmed till battery disconnection.
REMARK: the return to the “wave jammer” mode is possible by simultaneously push-
ing of the keys 2 and 5 putting the radio under tension. Wait then for two minutes. Programming
OBSERVAT ION:
In order to select the operation area of the radio receiver, simultaneously push keys
2 and 5, putting so the radio under tension. Wait then for about two minutes. Introduce
the four digits code, then :
General
vnx.su

86
86 - 5
AUTO RA DIO
OBSERVATION : the auto radio is provided with a sound tonality modification subject to
vehicle type. To modify that, see chapter “ configuration”.
Self-diagnostic
This mode is allowing some main functions controlling:
-speakers testing
by simultaneously pushing of 2 and 4 keys, the speakers are supplied one by one. The display
is enabling their location. - reception level testing ( afte r fr equency displaying)
by simultaneously pushing of 1 and 6 keys, the display is showing the radio reception criteria:
- 9 or letter = good reception
- 3 = defective signal
- 2 = stereo sound loosing
Keys testing
The introduction of this mode is performed by simultaneously pushing of 3 and on/off keys.
Each key pushing may be seen on display. The exit from this checking mode is automatic, after
all keys have been pushed.
General
vnx.su

86
86 - 6
AUTO RA DIO
TAPES PLAYER
This function is completely automatic, immediately after the tape is being inserted in the device
through the door provided for this purpose, the tape being oriented with the opening towards right.
Ta p e f a s t forwards
For this purpose, the “sau” key must be pressed. During tape rewinding, the radio may be heard
and on the display the name of the radio station or its frequency will be displayed. The stopping of
the fast forwards is to be performed by pushing on the key next to the one initially pushed. If during
a tape listening, you wish the listening of the other side, push simultaneou sly the key “si”. This tapes
player is an auto-reverse type, so when finishing listening one side of a tape, automatically the sense
will change and the listening of the other side will continue.
The MSS system is to be activated by pushing key “MSS”, enabling the fast forwards of the tape
till the ne xt song, does not matter t he playing sense in use. Deactivation of this function is to be
performed by pushing again key <>.
Noise reduction – Dolby B function
If you a re using recorded tapes with noise re duction t ype Dolby B, push key <<1>> for a n
optimal sound playing, on the display, Dolby symbol will appear.
Ta pes player
vnx.su

86
86 - 7
AUTO RA DIO
CD P LAYER
CD (compact disc) playing.
Insert the CD, with the recorded face downward, in the door located on the device front part.
The CD lecture is beginning with track number 1.
If the CD has been previously inserted, then you switch on listening to a radio station, in case
you wish to listen again to the CD, push key SRC and select CD. The CD playing will continue
from its last stop.
After listening the last CD track, the playing is continuing beginning with track no.1.
Observations:
- The CD playing may be interrupted by the receipted information if radio has been previously
programmed to operate” Emergency messages reception”.
- If you after inserting the CD, you hear an acoustic signal (bip), check if the CD is not dirty
or damaged.
Track selection
In order t o select the de sired t rack, push consequently > or < till you reach the searched
track. The CD lecture will continue from the selected track.
Fast forwards/back wards
Push key > or < and maintain it pushed, performing in this way, the forwards and consequently
backwards of the track listen in that moment.
CD tracks random playing
In order to activate this function, push ke y ( 1). After finishing random playing of all CD
tracks, the lecture will c ontinue until its stop controlling. If key > is pushed, passing to the next
track, random selected, will be performed. If key < is pushed, playing again of the existent track
will be performed. In order to return to the normal track playing ( successive playing), key (1) i s
to be pushed and to be maintained for few seconds.
CD eject.
After CD playing, if CD ejection is desired, push key (2) EJECT, placed on the left side of
the device front panel.
OBSERVATIONS:
This CD player is reading only CD audio parts. If on CD there are also non-audio parts, they
can not be red and on the display the track number followed by the message NO AUDIO will be
displayed.
If a CD without a ny audio t rack, i s inserted in CD player, this one will be refused and the
message NO AUDIO will be displayed on the screen.
This CD player is operating only with 12-cm diameter CD.
CD Player
vnx.su