display DACIA SOLENZA 2004 Owner's Manual
[x] Cancel search | Manufacturer: DACIA, Model Year: 2004, Model line: SOLENZA, Model: DACIA SOLENZA 2004Pages: 891, PDF Size: 14.84 MB
Page 650 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 10
Diagnostic – general
Configurationauto matic
auto matic Type of Cockpit
Central Unit
Only at N4
Only at N4
Denomination and symbol on CLIP tester
Ceiling lamp timing (LC021)
Radio-frequency function (LC089)
GENERAL CONFIGURATIONS OF THE COCKPIT CENTRAL UNIT
There are the following possible configurations of the cockpit Central Unit:
INT ERFACE BOX CONFIGURATION
Th is is performed by means of the CLIP tester, as follows:
〈 With the contact set on, enter in dialogue with the vehicle.
〈 Select and validate menu “ Interface box”
〈 In menu “Control module” , validate line “Configuration”.
〈 Select control : “CF716 : type N2” or
“CF010 : t ype N4”
〈 the following message shall be displayed: “Do you wish to continue?”
〈 Select “yes”, th e n p erf orm the automatic configuration.
- For Cockpit central Unit “base range” or “N2”
Configuration ce iling lamp with timer without
Con figuration ra d i o f r equency function without
- For Cockpit central Unit “high r ange” or “N4”
Configuration ce iling lamp with timer with
Con figuration ra d i o frequency function with
〈 Check then the configurations in menu “ Configuration reading”
vnx.su
Page 654 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 14
Diagnostic - Conformity checking
RECOMMENDATIONS Do not perform this conformity checking but after a competechecking by means of diagnostic tester. The values
displayed in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
1
2 Supply
Lighting PR002
: Battery voltage
ET002: +12 V after
c ontact
ET309: Right turning
information
ET310: L eft turning
information
ET291: H azard lights
information 12V < X
< 12,5V
Presen t
It is ACTIVE when
c ontrolling r ight
turning
It is ACTIVE when
controlling left turning
It is ACTIVE when
controlling hazard lights If problems occurring:
Perform a diagnostic of the charging circuit
If problems occurring: See state diagnostic
ET002
If is INACTIVE , see
state diagnostic ET309
If it is INACTIVE , see
state diagnostic ET310
If it is INACTIVE , see
state diagnostic ET291
No.
Function Par
ameter or state
Checking or action Visualization and
observations
Diagnos tic
vnx.su
Page 655 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 15
Diagnostic - Conformity checking
RECOMMENDATIONS Do not perform this conformity checking but after a competechecking by means of diagnostic tester. The values displayed
in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
3
4 Wiper
Opening ET213:
Windscreen
wiper timing
ET005: Windscreen
wiper fix point sto pping
ET192: : Front doors ACTIVE
, when
windscreen wi p e r
control in on timer
position
ACTIVE when
c ontrolling the wiper
on timer position, at
each wipe r stopping.
State OPEN when
opening the driver’s
doors If
it INACTIVE , see
state diagnostic ET213.
If problems occurring, apply the specific
diagnostic for
windscreen wiper fix point stopping failure DF119
If prob lems occurring: see
state diagnostic ET 192
No.
Function Par
ameter or state
Checking or action Visualization and
observations
Diagnos tic
vnx.su
Page 656 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 16
Diagnostic - Conformity checking
Do not perform this conformity checking but after a compete
checking by means of diagnostic tester. The values displayed
in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
RECOMMENDATIONS
Par ameter or state
Checking or action
ET010: Key RF valid
ET193: RF information
r eceived
ET012: source of last
r eceived co ntrol
ET105: Last received
c ontrol Visualization and
observations
State YES when
doors locking or
unlocking is done
using a remote control a ssigned to that UCH
.
State YES when
doors blocking/
unlocking is done using the remote
control
TRF when doors
locking/unloc king is
done u sing the remote
cont rol, CP E when
locking/unloc king is
done u sing the doors
central locking switch
UNL OCKI NG LOCK ING Diagnos tic
If problems occurring: see state diagnostic ET010
If problems occurring: see state diagnostic ET193
Nothing to notice
Nothing to notice
No.
1F unction
Opening
(ctd)
vnx.su
Page 657 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 17
Diagnostic – Conformity checking
At “N4” Cockpit Central Unit, some states and parameters are only displayed on the
scr een “Function test”. There are two function tests:
“Radio-Frequency”
“ET002: +12 volts after contact”
“ET193: RF received information”
“ET010: RF valid key”
“Doors management”
“ET192: front doors”
“ET105: last received control”
“ET012: source of last received control”
“ET216: CPE key”
vnx.su